typical values at T_A = 25°C, VA19 = 1.9 V, VA11 = VD11 = 1.1 V, default full-scale voltage (FS_RANGE_A = FS_RANGE_B = 0xA000), input signal applied to INA± in single-channel modes, f_IN = 347 MHz, A_IN = –1 dBFS, f_CLK = maximum-rated clock frequency, filtered, 1-V_PP sine-wave clock, JMODE = 1, dither enabled with default settings, VA11, VD11 and VS11 noise suppression ON (EN_VA11_NOISE_SUPPR = EN_VD11_NOISE_SUPPR = EN_VS11_NOISE_SUPPR = 1), and background calibration (unless otherwise noted); SNR results exclude DC, HD2 to HD9 and interleaving spurs; SINAD, ENOB, and SFDR results exclude DC and fixed-frequency interleaving spurs

Figure 5-1 Input Amplitude vs Input Frequency

Figure 5-3 DNL vs ADC Code

Figure 5-5 DES Mode: Single Tone FFT at 347 MHz

Figure 5-7 DES Mode: Single Tone FFT at 2397 MHz

Figure 5-9 DES Mode: Single Tone FFT at 5597 MHz

each tone at -7 dBFS, 100MHz Tone Spacing

Figure 5-11 DES Mode: Two Tone FFT at 347 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-13 DES Mode: Two Tone FFT at 2397 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-15 DES Mode: Two Tone FFT at 5597 MHz

Figure 5-17 Dual Channel Mode: Single Tone FFT at 347 MHz

Figure 5-19 Dual Channel Mode: Single Tone FFT at 2397 MHz

Figure 5-21 Dual Channel Mode: Single Tone FFT at 5597 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-23 Dual Channel Mode: Two Tone FFT at 347 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-25 Dual Channel Mode: Two Tone FFT at 2397 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-27 Dual Channel Mode: Two Tone FFT at 5597 MHz

AIN = –1 dBFS

Figure 5-29 DES Mode: SNR vs Sample Rate and Input Frequency

AIN = –12 dBFS

Figure 5-31 DES Mode: SNR vs Sample Rate and Input Frequency

AIN = –6 dBFS

Figure 5-33 DES Mode: SFDR vs Sample Rate and Input Frequency

AIN = –1 dBFS

Figure 5-35 DES Mode: HD2 vs Sample Rate and Input Frequency

AIN = –6 dBFS

Figure 5-37 DES Mode: HD2 vs Sample Rate and Input Frequency

AIN = –1 dBFS

Figure 5-39 DES Mode: HD3 vs Sample Rate and Input Frequency

AIN = –12 dBFS

Figure 5-41 DES Mode: HD3 vs Sample Rate and Input Frequency

Figure 5-43 DES Mode: Fs/4 + F_IN vs Sample Rate and Input Frequency

AIN = –1 dBFS

Figure 5-45 Dual Channel Mode: SNR vs Sample Rate and Input Frequency

AIN = –12 dBFS

Figure 5-47 Dual Channel Mode: SNR vs Sample Rate and Input Frequency

AIN = –6 dBFS

Figure 5-49 Dual Channel Mode: SFDR vs Sample Rate and Input Frequency

JMODE 3, AIN = –80 dBFS

Figure 5-51 Dual Channel Mode: NSD and Input Frequency

AIN = –6 dBFS

Figure 5-53 Dual Channel Mode: HD2 vs Sample Rate and Input Frequency

AIN = –1 dBFS

Figure 5-55 Dual Channel Mode: HD3 vs Sample Rate and Input Frequency

AIN = –12 dBFS

Figure 5-57 Dual Channel Mode: HD3 vs Sample Rate and Input Frequency

Figure 5-59 DES Mode: SNR vs Input Amplitude and Frequency

Figure 5-61 DES Mode: SFDR vs Input Amplitude and Frequency

Figure 5-63 DES Mode: HD2 vs Input Amplitude and Frequency

Figure 5-65 DES Mode: HD3 vs Input Amplitude and Frequency

Figure 5-67 DES Mode: Fs/2 - F_IN vs Input Amplitude and Frequency

Figure 5-69 DES Mode: Fs/4 + F_IN vs Input Amplitude and Frequency

Figure 5-71 DES Mode: Fs/4 - F_IN vs Input Amplitude and Frequency

Figure 5-73 Dual Channel Mode: SNR vs Input Amplitude and Frequency

Figure 5-75 Dual Channel Mode: SFDR vs Input Amplitude and Frequency

Figure 5-77 Dual Channel Mode: HD2 vs Input Amplitude and Frequency

Figure 5-79 Dual Channel Mode: HD3 vs Input Amplitude and Frequency

Figure 5-81 Dual Channel Mode: Fs/2 - F_IN vs Input Amplitude and Frequency

Figure 5-83 DES Mode: SNR vs Clock Amplitude

Figure 5-85 Dual Channel Mode: SNR vs Clock Amplitude

FG calibration at each temperature

Figure 5-87 DES Mode: SNR, SINAD and SFDR vs Temperature

FG calibration at each temperature

Figure 5-89 DES Mode: HD2, HD3 and Worst non-HD Spur vs Temperature

FG calibration at each temperature

Figure 5-91 Dual Channel Mode: SNR, SINAD and SFDR vs Temperature

FG calibration at each temperature

Figure 5-93 Dual Channel Mode: HD2, HD3 and Worst non-HD Spur vs Temperature

All supplies varied together

Figure 5-95 DES Mode: SNR, SINAD and SFDR vs Supply Voltage

All supplies varied together

Figure 5-97 Dual Channel Mode: SNR, SINAD and SFDR vs Supply Voltage

Figure 5-99 SNR, SFDR and SINAD vs Input Common Mode Voltage

each tone at -7dBFS

Figure 5-101 DES Mode: IMD3 vs Input Frequency

each tone at -7dBFS

Figure 5-103 DES Mode: IMD3 vs Tone Spacing

Figure 5-105 DES Mode: Two Tone SFDR vs Input Amplitude

Figure 5-107 Dual Chanel Mode: IMD3 vs Input Amplitude

Figure 5-109 Dual Chanel Mode: Two Tone SFDR vs Input Frequency

Dual channel mode, JMODE 3

Figure 5-2 Crosstalk vs Input Frequency

Figure 5-4 INL vs ADC Code

Figure 5-6 DES Mode: Single Tone FFT at 897 MHz

Figure 5-8 DES Mode: Single Tone FFT at 4197 MHz

Figure 5-10 DES Mode: Single Tone FFT at 7997 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-12 DES Mode: Two Tone FFT at 897 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-14 DES Mode: Two Tone FFT at 4197 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-16 DES Mode: Two Tone FFT at 7997 MHz

Figure 5-18 Dual Channel Mode: Single Tone FFT at 897 MHz

Figure 5-20 Dual Channel Mode: Single Tone FFT at 4197 MHz

Figure 5-22 Dual Channel Mode: Single Tone FFT at 7997 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-24 Dual Channel Mode: Two Tone FFT at 897 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-26 Dual Channel Mode: Two Tone FFT at 4197 MHz

each tone at -7 dBFS, 100 MHz Tone Spacing

Figure 5-28 Dual Channel Mode: Two Tone FFT at 7997 MHz

AIN = –6 dBFS

Figure 5-30 DES Mode: SNR vs Sample Rate and Input Frequency

AIN = –1 dBFS

Figure 5-32 DES Mode: SFDR vs Sample Rate and Input Frequency

AIN = –12 dBFS

Figure 5-34 DES Mode: SFDR vs Sample Rate and Input Frequency

JMODE 1, AIN = –80 dBFS

Figure 5-36 DES Mode: NSD vs Input Frequency

AIN = –12 dBFS

Figure 5-38 DES Mode: HD2 vs Sample Rate and Input Frequency

AIN = –6 dBFS

Figure 5-40 DES Mode: HD3 vs Sample Rate and Input Frequency

Figure 5-42 DES Mode: Fs/2 - F_IN vs Sample Rate and Input Frequency

Figure 5-44 DES Mode: Fs/4 - F_IN vs Sample Rate and Input Frequency

AIN = –6 dBFS

Figure 5-46 Dual Channel Mode: SNR vs Sample Rate and Input Frequency

AIN = –1 dBFS

Figure 5-48 Dual Channel Mode: SFDR vs Sample Rate and Input Frequency

AIN = –12 dBFS

Figure 5-50 Dual Channel Mode: SFDR vs Sample Rate and Input Frequency

AIN = –1 dBFS

Figure 5-52 Dual Channel Mode: HD2 vs Sample Rate and Input Frequency

AIN = –12 dBFS

Figure 5-54 Dual Channel Mode: HD2 vs Sample Rate and Input Frequency

AIN = –6 dBFS

Figure 5-56 Dual Channel Mode: HD3 vs Sample Rate and Input Frequency

Figure 5-58 Dual Channel Mode: Fs/2 - F_IN vs Sample Rate and Input Frequency

Figure 5-60 DES Mode: SNR vs Input Amplitude and Dither

Figure 5-62 DES Mode: SFDR vs Input Amplitude and Dither

Figure 5-64 DES Mode: HD2 vs Input Amplitude and Dither

Figure 5-66 DES Mode: HD3 vs Input Amplitude and Dither

Figure 5-68 DES Mode: Fs/2 - F_IN vs Input Amplitude and Dither

Figure 5-70 DES Mode: Fs/4 + F_IN vs Input Amplitude and Dither

Figure 5-72 DES Mode: Fs/4 - F_IN vs Input Amplitude and Dither

Figure 5-74 Dual Channel Mode: SNR vs Input Amplitude and Dither

Figure 5-76 Dual Channel Mode: SFDR vs Input Amplitude and Dither

Figure 5-78 Dual Channel Mode: HD2 vs Input Amplitude and Dither

Figure 5-80 Dual Channel Mode: HD3 vs Input Amplitude and Dither

Figure 5-82 Dual Channel Mode: Fs/2 - F_IN vs Input Amplitude and Dither

Figure 5-84 DES Mode: SFDR vs Clock Amplitude

Figure 5-86 Dual Channel Mode: SFDR vs Clock Amplitude

FG25 is calibrated at 25°C and held at other temperatures, other modes recalibrated at each temperature

Figure 5-88 DES Mode: SNR vs Temperature and Calibration Mode

FG25 is calibrated at 25°C and held at other temperatures, other modes recalibrated at each temperature

Figure 5-90 DES Mode: SFDR vs Temperature and Calibration Mode

FG25 is calibrated at 25°C and held at other temperatures, other modes recalibrated at each temperature

Figure 5-92 Dual Channel Mode: SNR vs Temperature and Calibration Mode

FG25 is calibrated at 25°C and held at other temperatures, other modes recalibrated at each temperature

Figure 5-94 Dual Channel Mode: SFDR vs Temperature and Calibration Mode

All supplies varied together

Figure 5-96 DES Mode: HD2, HD3 and Worst non-HD Spur vs Supply Voltage

All supplies varied together

Figure 5-98 Dual Channel Mode: HD2, HD3 and Worst non-HD Spur vs Supply Voltage

Figure 5-100 Fs/2 - F_IN and Fs/4 ± F_IN vs Input Common Mode Voltage

Figure 5-102 DES Mode: IMD3 vs Input Amplitude

each tone at -7dBFS

Figure 5-104 DES Mode: Two Tone SFDR vs Input Frequency

each tone at -7dBFS

Figure 5-106 Dual Chanel Mode: IMD3 vs Input Frequency

Figure 5-108 Dual Chanel Mode: IMD3 vs Tone Spacing

Figure 5-110 Dual Chanel Mode: Two Tone SFDR vs Input Amplitude

All modes capable of FS = 10.4GSPS

Figure 5-111 DES Mode: I_VA19 vs JMODE at 10.4GSPS

All modes capable of FS = 10.4GSPS

Figure 5-112 DES Mode: I_VA11 vs JMODE at 10.4GSPS

All modes capable of FS = 10.4GSPS

Figure 5-113 DES Mode: I_VD11 vs JMODE at 10.4GSPS

All modes capable of FS = 10.4GSPS

Figure 5-114 DES Mode: Power Dissipation vs JMODE at 10.4GSPS

All modes capable of FS = 5.2GSPS

Figure 5-115 Dual Channel Mode: I_VA19 vs JMODE at 5.2GSPS

All modes capable of FS = 5.2GSPS

Figure 5-116 Dual Channel Mode: I_VA11 vs JMODE at 5.2GSPS

All modes capable of FS = 5.2GSPS

Figure 5-117 Dual Channel Mode: I_VD11 vs JMODE at 5.2GSPS

All modes capable of FS = 5.2GSPS

Figure 5-118 Dual Channel Mode: Power Dissipation vs JMODE at 5.2GSPS

At maximum possible sample rate per Table 6-23

Figure 5-119 Other Modes with Lower Maximum F_S: I_VA19 vs JMODE

At maximum possible sample rate per Table 6-23

Figure 5-120 Other Modes with Lower Maximum F_S: I_VA11 vs JMODE

At maximum possible sample rate per Table 6-23

Figure 5-121 Other Modes with Lower Maximum F_S: I_VD11 vs JMODE

At maximum possible sample rate per Table 6-23

Figure 5-122 Other Modes with Lower Maximum F_S: Power Dissipation vs JMODE

independent of JMODE

Figure 5-123 DES Mode: I_VA19 vs Sample Rate

JMODE 1

Figure 5-125 DES Mode: I_VD11 vs Sample Rate

JMODE 30

Figure 5-127 DES Mode: I_VD11 vs Sample Rate

JMODE 1

Figure 5-129 DES Mode: Power Dissipation vs Sample Rate

JMODE 30

Figure 5-131 DES Mode: Power Dissipation vs Sample Rate

independent of JMODE

Figure 5-133 Dual Channel Mode: I_VA19 vs Sample Rate

JMODE 3

Figure 5-135 Dual Channel Mode: I_VD11 vs Sample Rate

JMODE 31

Figure 5-137 Dual Channel Mode: I_VD11 vs Sample Rate

JMODE 3

Figure 5-139 Dual Channel Mode: Power Dissipation vs Sample Rate

JMODE 31

Figure 5-141 Dual Channel Mode: Power Dissipation vs Sample Rate

Figure 5-143 Power Dissipation vs Temperature

Figure 5-145 Background Calibration Core Transition (AC Signal - zoomed)

Figure 5-147 Background Calibration Core Transition (DC Signal - zoomed)

Figure 5-149 Pulse Overdrive Recovery Zoomed

Figure 5-151 Sinewave Overdrive Recovery

independent of JMODE

Figure 5-124 DES Mode: I_VA11 vs Sample Rate

JMODE 21

Figure 5-126 DES Mode: I_VD11 vs Sample Rate

JMODE 61

Figure 5-128 DES Mode: I_VD11 vs Sample Rate

JMODE 21

Figure 5-130 DES Mode: Power Dissipation vs Sample Rate

JMODE 61

Figure 5-132 DES Mode: Power Dissipation vs Sample Rate

independent of JMODE

Figure 5-134 Dual Channel Mode: I_VA11 vs Sample Rate

JMODE 11

Figure 5-136 Dual Channel Mode: I_VD11 vs Sample Rate

JMODE 59

Figure 5-138 Dual Channel Mode: I_VD11 vs Sample Rate

JMODE 11

Figure 5-140 Dual Channel Mode: Power Dissipation vs Sample Rate

JMODE 59

Figure 5-142 Dual Channel Mode: Power Dissipation vs Sample Rate

Figure 5-144 Background Calibration Core Transition (AC Signal)

Figure 5-146 Background Calibration Core Transition (DC Signal)

Figure 5-148 Pulse Overdrive Recovery

Figure 5-150 Sinewave Overdrive Recovery