ZHCSOI5 October   2021 ADC12DJ1600 , ADC12QJ1600 , ADC12SJ1600

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 说明（续）
  5. 5 Revision History
  6. 6 Device Comparison
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Thermal Information
    5. 8.5  Electrical Characteristics: DC Specifications
    6. 8.6  Electrical Characteristics: Power Consumption
    7. 8.7  Electrical Characteristics: AC Specifications
    8. 8.8  Timing Requirements
    9. 8.9  Switching Characteristics
    10. 8.10 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Analog Input
        1. 9.3.1.1 Analog Input Protection
        2. 9.3.1.2 Full-Scale Voltage (VFS) Adjustment
        3. 9.3.1.3 Analog Input Offset Adjust
        4. 9.3.1.4 ADC Core
          1. 9.3.1.4.1 ADC Theory of Operation
          2. 9.3.1.4.2 ADC Core Calibration
          3. 9.3.1.4.3 Analog Reference Voltage
          4. 9.3.1.4.4 ADC Over-range Detection
          5. 9.3.1.4.5 Code Error Rate (CER)
      2. 9.3.2 Temperature Monitoring Diode
      3. 9.3.3 Timestamp
      4. 9.3.4 Clocking
        1. 9.3.4.1 Converter PLL (C-PLL) for Sampling Clock Generation
        2. 9.3.4.2 LVDS Clock Outputs (PLLREFO±, TRIGOUT±)
        3. 9.3.4.3 Optional CMOS Clock Outputs (ORC, ORD)
        4. 9.3.4.4 SYSREF for JESD204C Subclass-1 Deterministic Latency
          1. 9.3.4.4.1 SYSREF Capture for Multi-Device Synchronization and Deterministic Latency
          2. 9.3.4.4.2 SYSREF Position Detector and Sampling Position Selection (SYSREF Windowing)
      5. 9.3.5 JESD204C Interface
        1. 9.3.5.1  Transport Layer
        2. 9.3.5.2  Scrambler
        3. 9.3.5.3  Link Layer
        4. 9.3.5.4  8B or 10B Link Layer
          1. 9.3.5.4.1 Data Encoding (8B or 10B)
          2. 9.3.5.4.2 Multiiframes and the Local Multiframe Clock (LMFC)
          3. 9.3.5.4.3 Code Group Synchronization (CGS)
          4. 9.3.5.4.4 Initial Lane Alignment Sequence (ILAS)
          5. 9.3.5.4.5 Frame and Multiframe Monitoring
        5. 9.3.5.5  64B or 66B Link Layer
          1. 9.3.5.5.1 64B or 66B Encoding
          2. 9.3.5.5.2 Multiblocks, Extended Multiblocks and the Local Extended Multiblock Clock (LEMC)
            1. 9.3.5.5.2.1 Block, Multiblock and Extended Multiblock Alignment using Sync Header
              1. 9.3.5.5.2.1.1 Cyclic Redundancy Check (CRC) Mode
              2. 9.3.5.5.2.1.2 Forward Error Correction (FEC) Mode
          3. 9.3.5.5.3 Initial Lane Alignment
          4. 9.3.5.5.4 Block, Multiblock and Extended Multiblock Alignment Monitoring
        6. 9.3.5.6  Physical Layer
          1. 9.3.5.6.1 SerDes Pre-Emphasis
        7. 9.3.5.7  JESD204C Enable
        8. 9.3.5.8  Multi-Device Synchronization and Deterministic Latency
        9. 9.3.5.9  Operation in Subclass 0 Systems
        10. 9.3.5.10 Alarm Monitoring
          1. 9.3.5.10.1 Clock Upset Detection
          2. 9.3.5.10.2 FIFO Upset Detection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Low Power Mode and High Performance Mode
      2. 9.4.2 JESD204C Modes
        1. 9.4.2.1 JESD204C Transport Layer Data Formats
        2. 9.4.2.2 64B or 66B Sync Header Stream Configuration
        3. 9.4.2.3 Redundant Data Mode (Alternate Lanes)
      3. 9.4.3 Power-Down Modes
      4. 9.4.4 Test Modes
        1. 9.4.4.1 Serializer Test-Mode Details
        2. 9.4.4.2 PRBS Test Modes
        3. 9.4.4.3 Clock Pattern Mode
        4. 9.4.4.4 Ramp Test Mode
        5. 9.4.4.5 Short and Long Transport Test Mode
          1. 9.4.4.5.1 Short Transport Test Pattern
        6. 9.4.4.6 D21.5 Test Mode
        7. 9.4.4.7 K28.5 Test Mode
        8. 9.4.4.8 Repeated ILA Test Mode
        9. 9.4.4.9 Modified RPAT Test Mode
      5. 9.4.5 Calibration Modes and Trimming
        1. 9.4.5.1 Foreground Calibration Mode
        2. 9.4.5.2 Background Calibration Mode
        3. 9.4.5.3 Low-Power Background Calibration (LPBG) Mode
      6. 9.4.6 Offset Calibration
      7. 9.4.7 Trimming
    5. 9.5 Programming
      1. 9.5.1 Using the Serial Interface
      2. 9.5.2 SCS
      3. 9.5.3 SCLK
      4. 9.5.4 SDI
      5. 9.5.5 SDO
      6. 9.5.6 Streaming Mode
      7. 9.5.7 SPI_Register_Map Registers
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 Light Detection and Ranging (LiDAR) Digitizer
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
          1. 10.2.1.2.1 Analog Front-End Requirements
          2. 10.2.1.2.2 Calculating Clock and SerDes Frequencies
        3. 10.2.1.3 Application Curves
    3. 10.3 Initialization Set Up
  11. 11Power Supply Recommendations
    1. 11.1 Power Sequencing
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
    2. 13.2 接收文档更新通知
    3. 13.3 支持资源
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 术语表
  14. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息
9.3.5.5.2.1.1 Cyclic Redundancy Check (CRC) Mode

The cyclic redundancy check (CRC) mode is available to allow detection of potential bit errors during transmission. Support for the 12-bit word CRC-12 mode is required by JESD204C, while a 3-bit word CRC-3 mode is optional. The device does not support the CRC-3 mode and therefore this section is specific to the CRC-12 mode only. The transmitter computes the CRC-12 parity bits from the scrambled data bits of the 32 blocks of a multiblock. The 12-bit CRC parity word is then transmitted in the sync header stream of the next multiblock. The receiver computes the 12-bit parity word of the received multiblock and compares it against the received 12-bit parity word of the next multiblock. A difference indicates that there is at least one error in the received data bits or in the received 12-bit parity word. The minimum latency to the detection of a bit error in the first data bit of a multiblock is 46 blocks. Enable CRC-12 mode by setting SHMODE to 0.

The mapping of the sync header stream when using the CRC-12 mode is shown in Table 9-10. CRC[x] corresponds to bit x of the 12-bit CRC word. Cmd[x] corresponds to bit x of the 7 bit command word, which are always set to 0s in the device. The 00001 bit sequence at the end of the sync header stream is the pilot signal that is used to identify the end of a multiblock. The 1s that occur throughout the sync header ensure that the pilot signal can only be seen at the end of the sync header, allowing multiblock alignment after only a single multiblock has been received. EoEMB is the end-of-extended-multiblock bit, which is set to 1 for the last multiblock of an extended multiblock.

Table 9-10 Sync Header Stream Bit Mapping for CRC-12 Mode
BitFunctionBitFunctionBitFunctionBitFunction
0CRC[11]8CRC[5]16Cmd[6]24Cmd[2]
1CRC[10]9CRC[4]17Cmd[5]25Cmd[1]
2CRC[9]10CRC[3]18Cmd[4]26Cmd[0]
31111191270
4CRC[8]12CRC[2]20Cmd[3]280
5CRC[7]13CRC[1]211290
6CRC[6]14CRC[0]22EoEMB300
71151231311

The CRC-12 encoder takes in a multiblock of 32 scrambled blocks (2048 bits) and computes the 12-bit parity word using the generator polynomial given by Equation 10. The polynomial is sufficient to detect all 2-bit errors in a multiblock, spanning any distance, and burst error sequences of up to 12-bits in length. The probability of not detecting a 3-bit error spanning any distance in a multiblock is approximately 0.004%.

Equation 10. 0x987 == x12+x9+x8+x3+x2+x+1

The full parity bit generation for CRC-12 is shown in Figure 9-9. The input is a 2048 bit sequence, built from the 32 scrambled blocks of a multiblock (sync header is not included). The 12-bit parity word, CRC[11:0], is taken from the Sx blocks after the full 2048 bit sequence is processed. The Sx blocks are initialized with 0s before processing each multiblock. For more information on the CRC-12 parity word generation, refer to the JESD204C standard.

GUID-4F4CE4D0-8CC1-4628-8B49-8C5544537BAA-low.gifFigure 9-9 CRC-12 Parity Bit Generator
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |