ZHCSQZ8A May   2022  – December 2022 ADS1285

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements: 1.65 V ≤ IOVDD ≤ 1.95 V and 2.7 V ≤ IOVDD ≤ 3.6 V
    7. 6.7 Switching Characteristics: 1.65V ≤ IOVDD ≤ 1.95V and 2.7 V ≤ IOVDD ≤ 3.6 V
    8. 6.8 Timing Diagrams
    9. 6.9 Typical Characteristics
  7. 7 Parameter Measurement Information
    1. 7.1 Noise Performance
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Analog Input
      2. 8.3.2 PGA and Buffer
        1. 8.3.2.1 Programmable Gain Amplifier (PGA)
        2. 8.3.2.2 Buffer Operation (PGA Bypass)
      3. 8.3.3 Voltage Reference Input
      4. 8.3.4 IOVDD Power Supply
      5. 8.3.5 Modulator
        1. 8.3.5.1 Modulator Overdrive
      6. 8.3.6 Digital Filter
        1. 8.3.6.1 Sinc Filter Section
        2. 8.3.6.2 FIR Filter Section
        3. 8.3.6.3 Group Delay and Step Response
          1. 8.3.6.3.1 Linear Phase Response
          2. 8.3.6.3.2 Minimum Phase Response
        4. 8.3.6.4 HPF Stage
      7. 8.3.7 Clock Input
      8. 8.3.8 GPIO
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power Modes
      2. 8.4.2 Power-Down Mode
      3. 8.4.3 Reset
      4. 8.4.4 Synchronization
        1. 8.4.4.1 Pulse-Sync Mode
        2. 8.4.4.2 Continuous-Sync Mode
      5. 8.4.5 Sample Rate Converter
      6. 8.4.6 Offset and Gain Calibration
        1. 8.4.6.1 OFFSET Register
        2. 8.4.6.2 GAIN Register
        3. 8.4.6.3 Calibration Procedure
    5. 8.5 Programming
      1. 8.5.1 Serial Interface
        1. 8.5.1.1 Chip Select (CS)
        2. 8.5.1.2 Serial Clock (SCLK)
        3. 8.5.1.3 Data Input (DIN)
        4. 8.5.1.4 Data Output (DOUT)
        5. 8.5.1.5 Data Ready (DRDY)
      2. 8.5.2 Conversion Data Format
      3. 8.5.3 Commands
        1. 8.5.3.1  Single Byte Command
        2. 8.5.3.2  WAKEUP: Wake Command
        3. 8.5.3.3  STANDBY: Software Power-Down Command
        4. 8.5.3.4  SYNC: Synchronize Command
        5. 8.5.3.5  RESET: Reset Command
        6. 8.5.3.6  Read Data Direct
        7. 8.5.3.7  RDATA: Read Conversion Data Command
        8. 8.5.3.8  RREG: Read Register Command
        9. 8.5.3.9  WREG: Write Register Command
        10. 8.5.3.10 OFSCAL: Offset Calibration Command
        11. 8.5.3.11 GANCAL: Gain Calibration Command
    6. 8.6 Register Map
      1. 8.6.1 Register Descriptions
        1. 8.6.1.1 ID/SYNC: Device ID, SYNC Register (Address = 00h) [Reset = xxxx0000b]
        2. 8.6.1.2 CONFIG0: Configuration Register 0 (Address = 01h) [Reset = 12h]
        3. 8.6.1.3 CONFIG1: Configuration Register 1 (Address = 02h) [Reset = 00h]
        4. 8.6.1.4 HPF0, HPF1: High-Pass Filter Registers (Address = 03h, 04h) [Reset = 32h, 03h]
        5. 8.6.1.5 OFFSET0, OFFSET1, OFFSET2: Offset Calibration Registers (Address = 05h, 06h, 07h) [Reset = 00h, 00h, 00h]
        6. 8.6.1.6 GAIN0, GAIN1, GAIN2: Gain Calibration Registers (Address = 08h, 09h, 0Ah) [Reset = 00h, 00h, 40h]
        7. 8.6.1.7 GPIO: Digital Input/Output Register (Address = 0Bh) [Reset = 000xx000b]
        8. 8.6.1.8 SRC0, SRC1: Sample Rate Converter Registers (Address = 0Ch, 0Dh) [Reset = 00h, 80h]
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 Analog Power Supplies
      2. 9.3.2 Digital Power Supply
      3. 9.3.3 Grounds
      4. 9.3.4 Thermal Pad
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 接收文档更新通知
    2. 10.2 支持资源
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 术语表
  11. 11Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • RHB|32
散热焊盘机械数据 (封装 | 引脚)
订购信息

9.3.3 Grounds

The ADC has two ground pins, AGND and DGND. Connect the AGND and DGND pins together at the ADC to a single ground plane using short direct connections.

千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |