ZHCSIJ5C August   2018  – June 2019 ADS9224R , ADS9234R

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1.     Device Images
      1.      典型应用图
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics: ADS92x4R
    6. 6.6  Electrical Characteristics: ADS9224R
    7. 6.7  Electrical Characteristics: ADS9234R
    8. 6.8  Timing Requirements
    9. 6.9  Switching Characteristics
    10. 6.10 Typical Characteristics: ADS9224R
    11. 6.11 Typical Characteristics: ADS9234R
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Converter Modules
        1. 7.3.1.1 Analog Input With Sample-and-Hold
        2. 7.3.1.2 ADC Transfer Function
      2. 7.3.2 Internal Reference Voltage
      3. 7.3.3 Reference Buffers
      4. 7.3.4 REFby2 Buffer
      5. 7.3.5 Data Averaging
        1. 7.3.5.1 Averaging of Two Samples
        2. 7.3.5.2 Averaging of Four Samples
    4. 7.4 Device Functional Modes
      1. 7.4.1 ACQ State
      2. 7.4.2 CNV State
      3. 7.4.3 Reset or Power-Down
        1. 7.4.3.1 Reset
        2. 7.4.3.2 Power-Down
      4. 7.4.4 Conversion Control and Data Transfer Frame
        1. 7.4.4.1 Conversion Control and Data Transfer Frame With Zero Cycle Latency (Zone 1 Transfer)
        2. 7.4.4.2 Conversion Control and Data Transfer Frame With Wide Read Cycle (Zone 2 Transfer)
    5. 7.5 READY/STROBE Output
      1. 7.5.1 READY Output
      2. 7.5.2 STROBE Output
    6. 7.6 Programming
      1. 7.6.1 Output Data Word
      2. 7.6.2 Data Transfer Protocols
        1. 7.6.2.1 Protocols for Reading From the Device
          1. 7.6.2.1.1 Legacy, SPI-Compatible Protocols (SPI-xy-S-SDR)
          2. 7.6.2.1.2 SPI-Compatible Protocols With Bus Width Options and Single Data Rate (SPI-xy-D-SDR and SPI-xy-Q-SDR)
          3. 7.6.2.1.3 SPI-Compatible Protocols With Bus Width Options and Double Data Rate (SPI-x1-S-DDR, SPI-x1-D-DDR, SPI-x1-Q-DDR)
          4. 7.6.2.1.4 Clock Re-Timer (CRT) Protocols (CRT-S-SDR, CRT-D-SDR, CRT-Q-SDR, CRT-S-DDR, CRT-D-DDR, CRT-Q-DDR)
          5. 7.6.2.1.5 Parallel Byte Protocols (PB-xy-AB-SDR, PB-xy-AA-SDR)
        2. 7.6.2.2 Device Setup
          1. 7.6.2.2.1 Single Device: All Enhanced-SPI Options
          2. 7.6.2.2.2 Single Device: Minimum Pins for a Standard SPI Interface
        3. 7.6.2.3 Protocols for Configuring the Device
      3. 7.6.3 Reading and Writing Registers
    7. 7.7 Register Maps
      1. 7.7.1 ADS92x4R Registers
        1. 7.7.1.1 DEVICE_STATUS Register (Offset = 0h) [reset = 0h]
          1. Table 12. DEVICE_STATUS Register Field Descriptions
        2. 7.7.1.2 POWER_DOWN_CFG Register (Offset = 1h) [reset = 0h]
          1. Table 13. POWER_DOWN_CFG Register Field Descriptions
        3. 7.7.1.3 PROTOCOL_CFG Register (Offset = 2h) [reset = 0h]
          1. Table 14. PROTOCOL_CFG Register Field Descriptions
        4. 7.7.1.4 BUS_WIDTH Register (Offset = 3h) [reset = 0h]
          1. Table 15. BUS_WIDTH Register Field Descriptions
        5. 7.7.1.5 CRT_CFG Register (Offset = 4h) [reset = 0h]
          1. Table 16. CRT_CFG Register Field Descriptions
        6. 7.7.1.6 OUTPUT_DATA_WORD_CFG Register (Offset = 5h) [reset = 0h]
          1. Table 17. OUTPUT_DATA_WORD_CFG Register Field Descriptions
        7. 7.7.1.7 DATA_AVG_CFG Register (Offset = 6h) [reset = 0h]
          1. Table 18. DATA_AVG_CFG Register Field Descriptions
        8. 7.7.1.8 REFBY2_OFFSET Register (Offset = 7h) [reset = 0h]
          1. Table 19. REFBY2_OFFSET Register Field Descriptions
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 ADC Input Driver
        1. 8.1.1.1 Charge-Kickback Filter
      2. 8.1.2 Input Amplifier Selection
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
      1. 10.1.1 Signal Path
      2. 10.1.2 Grounding and PCB Stack-Up
      3. 10.1.3 Decoupling of Power Supplies
      4. 10.1.4 Reference Decoupling
      5. 10.1.5 Differential Input Decoupling
    2. 10.2 Layout Example
  11. 11器件和文档支持
    1. 11.1 器件支持
      1. 11.1.1 开发支持
    2. 11.2 相关文档
    3. 11.3 相关链接
    4. 11.4 接收文档更新通知
    5. 11.5 社区资源
    6. 11.6 商标
    7. 11.7 静电放电警告
    8. 11.8 Glossary
  12. 12机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.4.4.2 Conversion Control and Data Transfer Frame With Wide Read Cycle (Zone 2 Transfer)

In this mode of conversion control and data transfer, the device starts conversion on the rising edge of CONVST. The CONVST pin can be pulled low after a minimum time of tWH_CONVST. After a time of tD_CONVST_CS (see tD_CONVST_CS for zone 2 transfer in the Specifications section), the host must pull CS low and provide clocks on the SCLK pin to read the data in zone 2. As shown in Figure 45, a zone 2 transfer provides more read time (tread). The read time available for reading data is maximized when tD_CONVST_CS is set to the minimum permissible value. The data for the previous sample (sample N-1) is provided by the device on the SDO pins. After all bits are read, the host can pull the CS pin high to end the data transfer frame. After pulling CS high, the host can pull the CONVST pin high to start the next conversion. In this mode of conversion control, a minimum time of tCYCLE (see tCYCLE for zone 2 transfer in the Specifications section) is required between two adjacent rising edges of the CONVST signal. The host must keep the SDI pin low (NOP0) or high (NOP1) for conversion control and for getting conversion results from the device.

ADS9224R ADS9234R timing-conv-zone2-sbas876.gif
1. The READY output is not required for zone 2 data transfer. The STROBE output is required only for clock re-timer (CRT) protocols. See the READY/STROBE Output section for details.
2. For tREAD with different data transfer protocols; see the Protocols for Reading From the Device section.
3. fSample = 1 / tcycle.
Figure 45. Conversion Control and Data Transfer Frame With Wide Read Cycle (Zone 2 Transfer)

NOTE

For optimum performance with zone 2 transfer, TI recommends masking the READY output by setting the READY_MASK bit in the OUTPUT_DATA_WORD_CFG register and using a data transfer protocol with a bus width of more than 2 SDOs or the parallel byte protocol to keep [tD_CONVST_CS + tREAD] below 150 ns. See the Protocols for Reading From the Device section for details on different protocols for reading the data.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |