ZHCSJZ9B june   2019  – august 2023 BQ25155

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 说明（续）
  7. 6 Device Key Default Settings
  8. 7 Pin Configuration and Functions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Linear Charger and Power Path
        1. 9.3.1.1 Battery Charging Process
          1. 9.3.1.1.1 Pre-Charge
          2. 9.3.1.1.2 Fast Charge
          3. 9.3.1.1.3 Pre-Charge to Fast Charge Transitions and Charge Current Ramping
          4. 9.3.1.1.4 Termination
        2. 9.3.1.2 JEITA and Battery Temperature Dependent Charging
        3. 9.3.1.3 Input Voltage Based Dynamic Power Management (VINDPM) and Dynamic Power Path Management (DPPM)
        4. 9.3.1.4 Battery Supplement Mode
      2. 9.3.2  Protection Mechanisms
        1. 9.3.2.1 Input Over-Voltage Protection
        2. 9.3.2.2 Safety Timer and I2C Watchdog Timer
        3. 9.3.2.3 Thermal Protection and Thermal Charge Current Foldback
        4. 9.3.2.4 Battery Short and Over Current Protection
        5. 9.3.2.5 PMID Short Circuit
      3. 9.3.3  ADC
        1. 9.3.3.1 ADC Operation in Active Battery Mode and Low Power Mode
        2. 9.3.3.2 ADC Operation When VIN Present
        3. 9.3.3.3 ADC Measurements
        4. 9.3.3.4 ADC Programmable Comparators
      4. 9.3.4  VDD LDO
      5. 9.3.5  Load Switch/LDO Output and Control
      6. 9.3.6  PMID Power Control
      7. 9.3.7  System Voltage (PMID) Regulation
      8. 9.3.8  MR Wake and Reset Input
        1. 9.3.8.1 MR Wake or Short Button Press Functions
        2. 9.3.8.2 MR Reset or Long Button Press Functions
      9. 9.3.9  14-Second Watchdog for HW Reset
      10. 9.3.10 Faults Conditions and Interrupts ( INT)
        1. 9.3.10.1 Flags and Fault Condition Response
      11. 9.3.11 Power Good ( PG) Pin
      12. 9.3.12 External NTC Monitoring (TS)
        1. 9.3.12.1 TS Thresholds
      13. 9.3.13 External NTC Monitoring (ADCIN)
      14. 9.3.14 I2C Interface
        1. 9.3.14.1 F/S Mode Protocol
    4. 9.4 Device Functional Modes
      1. 9.4.1 Ship Mode
      2. 9.4.2 Low Power
      3. 9.4.3 Active Battery
      4. 9.4.4 Charger/Adapter Mode
      5. 9.4.5 Power-Up/Down Sequencing
    5. 9.5 Register Map
      1. 9.5.1 I2C Registers
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Input (IN/PMID) Capacitors
        2. 10.2.2.2 VDD, LDO Input and Output Capacitors
        3. 10.2.2.3 TS
        4. 10.2.2.4 Recommended Passive Components
      3. 10.2.3 Application Curves
  12. 11Power Supply Recommendations
  13. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  14. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 第三方米6体育平台手机版_好二三四免责声明
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 接收文档更新通知
    4. 13.4 支持资源
    5. 13.5 静电放电警告
    6. 13.6 Trademarks
    7. 13.7 术语表
  15. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

9.3.10.1 Flags and Fault Condition Response

Table 9-5 below details the BQ25155 behavior when a fault condition occurs.

Table 9-5 Interrupt Triggers and Fault Condition Response
FAULT / FLAGDESCRIPTIONINTERRUPT TRIGGER BASED ON STATUS BIT CHANGECHARGER BEHAVIORCHARGER SAFETY TIMERLS/LDO BEHAVIORPMID BEHAVIORNOTES
CHRG_CV_FLAGSet when charger enters Constant Voltage operationRising EdgeEnabledNo effectN/AIN powered if VIN is valid
CHARGE_DONE_FLAGSet when charger reaches terminationRising EdgePaused- Charging resumes with VIN or CE toggle or when VRCH is reachedResetN/AIN powered if VIN is valid
IINLIM_ACTIVE_FLAGSet when Input Current Limit loop is activeRising EdgeEnabled. Reduced charge current.Doubled if option is enabledN/AIN powered VIN powered unless supplement mode condition is met.
VDPPM_ACTIVE_FLAGSet when DPPM loop is activeRising EdgeEnabled. Reduced charge current.Doubled if option is enabledN/AVIN powered unless supplement mode condition is met.
VINDPM_ACTIVE_FLAGSet when VINDPM loop is activeRising EdgeEnabled. Reduced charge current.Doubled if option is enabledN/AVIN powered unless supplement mode condition is met.
THERMREG_ACTIVESet when Thermal Charge Current Foldback (Thermal Regulation) loop is activeRising EdgeEnabled. Reduced charge current.Doubled if option is enabledN/AVIN powered unless supplement mode condition is met.
VIN_PGOOD_FLAGSet when VIN changes PGOOD statusRising and Falling EdgeIf VIN_PGOOD_STAT is low, charging is disabled.ResetN/AVIN powered (if VIN_PGOOD_STAT=1) unless PMID_MODE is not 00.Interrupt will not be sent if device powers up with VIN_PGOOD condition and VBAT < VBATUVLO
VIN_OVP_FAULT_FLAGSet when VIN > VOVPRising EdgeCharging is paused until condition disappearsResetN/ABAT powered
BAT_OCP_FAULT_FLAGSet when IBAT > IBATOCPRising EdgeDisabled (BAT only condition)N/AN/ADisconnect BAT
BAT_UVLO_FAULT_FLAGSet when VBAT < VBATUVLORising EdgeEnabledNo effectN/AIN powered of VIN is valid
TS_COLD_FLAGSet when VTS > VTS_COLDRising EdgeCharging paused until condition is clearedPausedN/AIN powered of VIN is valid
TS_COOL_FLAGSet when VTS_COLD > VTS > VTS_COOLRising EdgeEnabled. Reduced charge current.Doubled if option is enabledN/AIN powered of VIN is valid
TS_WARM_FLAGSet when VTS_HOT < VTS < VTS_WARMRising EdgeEnabled. Reduce battery regulation voltage.No effectN/AIN powered of VIN is valid
TS_HOT_FLAGSet when VTS < VHOTRising EdgeCharging paused until condition is clearedPausedN/AIN powered of VIN is valid
ADC_READY_FLAGSet when ADC conversion is completedRising EdgeN/AN/AN/AN/A
COMP1_ALARM_FLAGSet when ADC measurement meets programmed conditionRising EdgeN/AN/AN/AN/A
COMP2_ALARM_FLAGSet when ADC measurement meets programmed conditionRising EdgeN/AN/AN/AN/A
COMP3_ALARM_FLAGSet when ADC measurement meets programmed conditionRising EdgeN/AN/AN/AN/A
TS_OPEN_FLAGSet when VTS > VTS_OPENRising EdgeCharging is paused until condition disappearsPausedN/AN/A
WD_FAULT_FLAGSet when I2C watchdog timer expiresRising EdgeEnabledN/AN/AN/A
SAFETY_TMR_FAULT_FLAGSet when safety Timer expires. Cleared after VIN or CE toggleRising EdgeDisabled until VIN or CE toggleReset after flag is clearedN/AIN powered of VIN is valid
LS_LDO_OCP_FAULT_FLAGSet when LDO output current exceeds OCP conditionRising EdgeN/AN/AEnabled (host must take action to disable the LDO if desired)N/A
MRWAKE1_TIMEOUT_FLAGSet when MR is low for at least tWAKE1Rising EdgeN/AN/AN/AN/A
MRWAKE2_TIMEOUT_FLAGSet when MR is low for at least tWAKE2Rising EdgeN/AN/AN/AN/A
MRRESET_WARN_FLAGSet when MR is low for at least tRESETWARNRising EdgeN/AN/AN/AN/A
TSHUTNo flag. Die temperature exceeds thermal shutdown threshold is reachedN/ADisabledDisabledDisabledDisabled
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |