ZHCSNB9 february   2021 BQ25300

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 说明（续）
  7. 6 Device Comparison Table
  8. 7 Pin Configuration and Functions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Device Power Up
        1. 9.3.1.1 Power-On-Reset (POR)
        2. 9.3.1.2 REGN Regulator Power Up
        3. 9.3.1.3 Charger Power Up
        4. 9.3.1.4 Charger Enable and Disable by EN Pin
        5. 9.3.1.5 Device Unplugged from Input Source
      2. 9.3.2 Battery Charging Management
        1. 9.3.2.1 Battery Charging Profile
        2. 9.3.2.2 Precharge
        3. 9.3.2.3 Charging Termination
        4. 9.3.2.4 Battery Recharge
        5. 9.3.2.5 Charging Safety Timer
        6. 9.3.2.6 Thermistor Temperature Monitoring
      3. 9.3.3 Charging Status Indicator (STAT)
      4. 9.3.4 Protections
        1. 9.3.4.1 Voltage and Current Monitoring
          1. 9.3.4.1.1 Input Over-Voltage Protection
          2. 9.3.4.1.2 Input Voltage Dynamic Power Management (VINDPM)
          3. 9.3.4.1.3 Input Current Limit
          4. 9.3.4.1.4 Cycle-by-Cycle Current Limit
        2. 9.3.4.2 Thermal Regulation and Thermal Shutdown
        3. 9.3.4.3 Battery Protection
          1. 9.3.4.3.1 Battery Over-Voltage Protection (VBAT_OVP)
          2. 9.3.4.3.2 Battery Short Circuit Protection
        4. 9.3.4.4 ICHG Pin Open and Short Protection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Disable Mode, HiZ Mode, Sleep Mode, Charge Mode, Termination Mode, and Fault Mode
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 Typical Application
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
          1. 10.2.1.2.1 Charge Voltage Settings
          2. 10.2.1.2.2 Charge Current Setting
          3. 10.2.1.2.3 Inductor Selection
          4. 10.2.1.2.4 Input Capacitor
          5. 10.2.1.2.5 Output Capacitor
        3. 10.2.1.3 Application Curves
      2. 10.2.2 Typical Application with External Power Path
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
        3. 10.2.2.3 Application Curves
  12. 11Power Supply Recommendations
  13. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  14. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 第三方米6体育平台手机版_好二三四免责声明
    2. 13.2 接收文档更新通知
    3. 13.3 支持资源
    4. 13.4 Trademarks
    5. 13.5 静电放电警告
    6. 13.6 术语表
  15. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.5 Electrical Characteristics

VVBUS_UVLOZ < VVBUS < VVBUS_OVP and VVBUS > VBAT + VSLEEP, L=2.2µH, TJ = -40°C to +125°C, and TJ = 25°C for typical values (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
QUIESCENT CURRENT
IVBUS_REVS VBUS reverse current from BAT/SW to VBUS TJ = -40°C - 85°C VBAT = VSW = 4.5V, VBUS is shorted to GND, measure VBUS reverse current 0.07 3 µA
IQ_VBUS_DIS VBUS leakage current in disable mode TJ = -40°C - 85°C VBUS = 5V, VBAT = 4V, charger is disabled, /EN is pulled high 3.5 4.25 µA
IQ_BAT_HIZ BAT and SW pin leakage current in HiZ mode TJ = -40°C - 65°C VBAT = VSW = 4.5V, VBUSfloating 0.17 1 µA
VBUS POWER UP
VVBUS_OP VBUS operating range 4.1 17.0 V
VVBUS_UVLOZ VBUS power on reset VBUS rising 3.0 3.80 V
VVBUS_UVLOZ_HYS VBUS power on reset hysteresis VBUS falling 250 mV
VVBUS_LOWV A condition to turnon REGN VBUS rising, REGN turns on, VBAT = 3.2V 3.8 3.90 4.00 V
VVBUS_LOWV_HYS A condition to turnon REGN, hysteresis VBUS falling, REGN turns off, VBAT = 3.2V 300 mV
VSLEEP Enter sleep mode threshold VBUS falling, VBUS - VBAT, VVBUS_LOWV < VBAT < VBATREG 30 60 100 mV
VSLEEPZ Exit sleep mode threshold VBUS rising, VBUS - VBAT, VVBUS_LOWV < VBAT < VBATREG 110 157 295 mV
VVBUS_OVP_RISE VBUS overvoltage rising threshold VBUS rising, converter stops switching 17.00 17.40 17.80 V
VVBUS_OVP_HYS VBUS overvoltage falling hysteresis VBUS falling, converter stops switching 750 mV
MOSFETS
RDSON_Q1 Top reverse blocking MOSFET on-resistance between VBUS and PMID (Q1) VREGN = 5V 40 65 mΩ
RDSON_Q2 High-side switching MOSFET on-resistance between PMID and SW (Q2) VREGN = 5V 50 82 mΩ
RDSON_Q3 Low-side switching MOSFET on-resistance between SW and GND (Q3) VREGN = 5V 45 72 mΩ
BATTERY CHARGER
VBATREG Charge voltage regulation VSET pin floating, TJ = -40°C to +85°C 3.582 3.6 3.618 V
Connect VSET pin to 51kΩ resistor, TJ = -40°C to +85°C 4.13 4.15 4.170 V
Connect VSET pin to 10kΩ resistor, TJ = -40°C to +85°C 4.179 4.200 4.221 V
VSET pin is grounded, TJ = -40°C to +85°C 4.03 4.050 4.070 V
ICHG Charge current regulation ICHG set at 1.72A with RICHG = 23.2kΩ 1.55 1.72 1.89 A
ICHG set at 1.0A with RICHG = 40.2kΩ 0.90 1.00 1.10 A
ICHG set at 0.5A with RICHG = 78.7kΩ 0.40 0.50 0.60 A
ITERM Termination current regulation ICHG = 1.72A, 10% of ICHG, RICHG = 23.2kΩ 138 172 206 mA
ICHG = 1.0A, 10% of ICHG, RICHG = 40.2kΩ 70 100 130 mA
ICHG = 0.5A, ITERM = 63mA, RICHG = 78.7kΩ 33 63 93 mA
IPRECHG Precharge current ICHG = 1.72A, 10% of ICHG, RICHG = 23.2kΩ 115 172 225 mA
ICHG = 1.0A, 10% of ICHG, RICHG = 40.2kΩ 50 100 150 mA
ICHG = 0.5A, RICHG = 78.7kΩ 28 63 98 mA
VBAT_SHORT_RISE VBAT short rising threshold Short to precharge 2.05 2.20 2.35 V
VBAT_SHORT_FALL VBAT short falling threshold Precharge to short 1.85 2.00 2.15 V
IBAT_SHORT Battery short current VBAT < VBAT_SHORT_FALL, 25 35 46 mA
VBAT_LOWV_RISE Rising threshold Precharge to fast charge 2.90 3.00 3.10 V
VBAT_LOWV_FALL Falling threshold Fast charge to precharge 2.60 2.70 2.80 V
VRECHG_HYS Recharge hysteresis below VBATREG VBAT falling 110 160 216 mV
INPUT VOLTAGE / CURRENT REGULATION
VINDPM_MIN Minimum input voltage regulation VBAT = 3.5V, measured at PMID pin 3.9 4.00 4.1 V
VINDPM Input voltage regulation VBAT = 4V, measured at PMID pin, VINDPM = 1.085*VBAT+ 0.025V 4.27 4.37 4.47 V
IINDPM_3A Input current regulation VBUS = 5V 3.00 3.35 3.70 A
BATTERY OVER-VOLTAGE PROTECTION
VBAT_OVP_RISE
Battery overvoltage rising threshold

 VBAT rising, as percentage of VBATREG (VBATREG = 4.15V) 104.0 %
VBAT_OVP_RISE Battery overvoltage rising threshold VBAT rising, as percentage of VBATREG 101.9 103.5 105.0 %
VBAT_OVP_FALL Battery overvoltage falling threshold VBAT falling, as percentage of VBATREG 100.0 101.6 103.1 %
CONVERTER PROTECTION
VBTST_REFRESH Bootstrap refresh comparator threshold (VBTST - VSW) when LSFET refresh pulse is requested, VBUS = 5V 2.7 3 3.3 V
IHSFET_OCP HSFET cycle by cycle over current limit threshold 5.2 6.2 6.7 A
STAT INDICATION
ISTAT_SINK STAT pin sink current 6 mA
FBLINK2 STAT pin blink frequency 1 Hz
FBLINK_DUTY STAT pin blink duty cycle 50 %
THERMAL REGULATION AND THERMAL SHUTDOWN
TREG Junction temperature regulation accuracy 111 120 133 °C
TSHUT Thermal Shutdown Rising threshold Temperature increasing 150 °C
Thermal Shutdown Falling threshold Temperature decreasing 125 °C
BUCK MODE OPERATION
FSW PWM switching frequency SW node frequency 1.02 1.20 1.38 MHz
DMAX Maximum PWM Duty Cycle 97.0 %
REGN LDO
VREGN_UVLO REGN UVLO VVBUS rising 3.85 V
VREGN REGN LDO output voltage VVBUS = 5V, IREGN = 0 to 16mA 4.20 5.0 V
VREGN REGN LDO output voltage VVBUS = 12V, IREGN = 16mA 4.50 5.40 V
ICHG SETTING
VICHG ICHG pin regulated voltage 993 998 1003 mV
RICHG_SHORT_FALL Resistance to disable charge 1.00 kΩ
RICHG_OPEN_RISE Resistance to disable charge 565 kΩ
RICHG Programmable resistance at ICHG VBUS = 5V, resistance decrease 11.70 250 kΩ
RICHG_HIGH ICHG setting resistor threshold to clamp precharge and termination current to 63mA RICHG > RICHG_HIGH 60.0 65.0 70.0 kΩ
KICHG Charge current ratio ICHG set at 1.72A with RICHG = 23.2kΩ, VBAT = 3.8V, VBUS = 5V, ICHG = KICHG / RICHG 36000 40000 44000 AxΩ
ICHG set at 1.0A with RICHG = 40.2kΩ, VBAT = 3.8V, VBUS = 5V, ICHG = KICHG / RICHG 36000 40280 44000 AxΩ
ICHG set at 0.5A with RICHG = 78.7kΩ, VBAT = 3.8V, VBUS = 5V, ICHG = KICHG / RICHG 32000 40700 48000 AxΩ
JEITA THERMISTOR COMPARATORS
COLD/HOT THERMISTOR COMPARATOR
VT1% TCOLD (0°C) threshold, charge suspended if thermistor temperature is below T1 VTS rising, as percentage to VREGN 72.68 73.5 74.35 %
VT1% VTS falling As Percentage to VREGN 70.68 71.5 72.33 %
VT3% THOT (45°C) threshold, charge suspended if thermistor temperature is above T3 VTS falling, as percentage to VREGN 46.35 47.25 48.15 %
VT3% VTS Rising As percentage to VREGN 47.35 48.25 49.15 %
LOGIC I/O PIN CHARACTERESTICS (POL, EN)
VILO Input low threshold Falling 0.40 V
VIH Input high threshold Rising 1.3 V
IBIAS High-level leakage current at EN pin EN pin is pulled up to 1.8 V 1.0 µA
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |