ZHCSO20 may 2021 BQ25723
PRODUCTION DATA
- 1
- 1 特性
- 2 应用
- 3 说明
- 4 Revision History
- 5 Description (continued)
- 6 Device Comparison Table
- 7 Pin Configuration and Functions
- 8 Specifications
-
9 Detailed Description
- 9.1 Overview
- 9.2 Functional Block Diagram
- 9.3
Feature Description
- 9.3.1 Power-Up Sequence
- 9.3.2 Vmin Active Protection (VAP) with Battery only
- 9.3.3 Two-Level Battery Discharge Current Limit
- 9.3.4 Fast Role Swap Feature
- 9.3.5 CHRG_OK Indicator
- 9.3.6 Input and Charge Current Sensing
- 9.3.7 Input Voltage and Current Limit Setup
- 9.3.8 Battery Cell Configuration
- 9.3.9 Device HIZ State
- 9.3.10 USB On-The-Go (OTG)
- 9.3.11 Converter Operation
- 9.3.12 Inductance Detection Through IADPT Pin
- 9.3.13 Converter Compensation
- 9.3.14 Continuous Conduction Mode (CCM)
- 9.3.15 Pulse Frequency Modulation (PFM)
- 9.3.16 Switching Frequency and Dithering Feature
- 9.3.17 Current and Power Monitor
- 9.3.18 Input Source Dynamic Power Management
- 9.3.19 Input Current Optimizer (ICO)
- 9.3.20 Two-Level Adapter Current Limit (Peak Power Mode)
- 9.3.21 Processor Hot Indication
- 9.3.22
Device Protection
- 9.3.22.1 Watchdog Timer
- 9.3.22.2 Input Overvoltage Protection (ACOV)
- 9.3.22.3 Input Overcurrent Protection (ACOC)
- 9.3.22.4 System Overvoltage Protection (SYSOVP)
- 9.3.22.5 Battery Overvoltage Protection (BATOVP)
- 9.3.22.6 Battery Discharge Overcurrent Protection (BATOC)
- 9.3.22.7 Battery Short Protection (BATSP)
- 9.3.22.8 System Undervoltage Lockout (VSYS_UVP) and Hiccup Mode
- 9.3.22.9 Thermal Shutdown (TSHUT)
- 9.4 Device Functional Modes
- 9.5 Programming
- 9.6
Register Map
- 9.6.1 ChargeOption0 Register (I2C address = 01/00h) [reset = E70Eh]
- 9.6.2 ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]
- 9.6.3 ChargeVoltage Register (I2C address = 05/04h) [reset value based on CELL_BATPRESZ pin setting]
- 9.6.4 ChargerStatus Register (I2C address = 21/20h) [reset = 0000h]
- 9.6.5 ProchotStatus Register (I2C address = 23/22h) [reset = B800h]
- 9.6.6 IIN_DPM Register (I2C address = 25/24h) [reset = 4100h]
- 9.6.7 ADCVBUS/PSYS Register (I2C address = 27/26h)
- 9.6.8 ADCIBAT Register (I2C address = 29/28h)
- 9.6.9 ADCIIN/CMPIN Register (I2C address = 2B/2Ah)
- 9.6.10 ADCVSYS/VBAT Register (I2C address = 2D/2Ch)
- 9.6.11 ChargeOption1 Register (I2C address = 31/30h) [reset = 3300h]
- 9.6.12 ChargeOption2 Register (I2C address = 33/32h) [reset = 00B7]
- 9.6.13 ChargeOption3 Register (I2C address = 35/34h) [reset = 0434h]
- 9.6.14 ProchotOption0 Register (I2C address = 37/36h) [reset = 4A81h(2S~4s) 4A09(1S)]
- 9.6.15 ProchotOption1 Register (I2C address = 39/38h) [reset = 41A0h]
- 9.6.16 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]
- 9.6.17 ChargeOption4 Register (I2C address = 3D/3Ch) [reset = 0048h]
- 9.6.18 Vmin Active Protection Register (I2C address = 3F/3Eh) [reset = 006Ch(2s~4s)/0004h(1S)]
- 9.6.19 OTGVoltage Register (I2C address = 07/06h) [reset = 09C4h]
- 9.6.20 OTGCurrent Register (I2C address = 09/08h) [reset = 3C00h]
- 9.6.21 InputVoltage(VINDPM) Register (I2C address = 0B/0Ah) [reset =VBUS-1.28V]
- 9.6.22 VSYS_MIN Register (I2C address = 0D/0Ch) [reset value based on CELL_BATPRESZ pin setting]
- 9.6.23 IIN_HOST Register (I2C address = 0F/0Eh) [reset = 4100h]
- 9.6.24 ID Registers
- 10Application and Implementation
- 11Power Supply Recommendations
- 12Layout
- 13Device and Documentation Support
- 14Mechanical, Packaging, and Orderable Information
9.5.1.4 Byte Format
Every byte on the SDA line must be 8 bits long. The number of bytes to be transmitted per transfer is unrestricted. Each byte has to be followed by an Acknowledge bit. Data is transferred with the Most Significant Bit (MSB) first. If a target cannot receive or transmit another complete byte of data until it has performed some other function, it can hold the clock line SCL low to force the host into a wait state (clock stretching). Data transfer then continues when the target is ready for another byte of data and release the clock line SCL.
Figure 9-10 Data Transfer on the
I2C Bus