ZHCSJL4A February   2019  – March 2019 BQ25883

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1.     简化原理图
  4. 4 修订历史记录
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Device Power-On-Reset
      2. 8.3.2  Device Power Up from Battery without Input Source
      3. 8.3.3  Device Power Up from Input Source
        1. 8.3.3.1 Poor Source Qualification
        2. 8.3.3.2 Input Source Type Detection
          1. 8.3.3.2.1 D+/D– Detection Sets Input Current Limit
          2. 8.3.3.2.2 Force Input Current Limit Detection
        3. 8.3.3.3 Power Up REGN Regulator (LDO)
        4. 8.3.3.4 Converter Power Up
      4. 8.3.4  Input Current Optimizer (ICO)
      5. 8.3.5  Buck Mode Operation from Battery (OTG)
      6. 8.3.6  Power Path Management
        1. 8.3.6.1 Narrow VDC Architecture
        2. 8.3.6.2 Dynamic Power Management
        3. 8.3.6.3 Supplement Mode
      7. 8.3.7  Battery Charging Management
        1. 8.3.7.1 Autonomous Charging Cycle
        2. 8.3.7.2 Battery Charging Profile
        3. 8.3.7.3 Charging Termination
        4. 8.3.7.4 Thermistor Qualification
          1. 8.3.7.4.1 JEITA Guideline Compliance in Charge Mode
          2. 8.3.7.4.2 Cold/Hot Temperature Window in OTG Buck Mode
        5. 8.3.7.5 Charging Safety Timer
      8. 8.3.8  Integrated 16-Bit ADC for Monitoring
      9. 8.3.9  Status Outputs
        1. 8.3.9.1 Power Good Indicator (PG)
        2. 8.3.9.2 Charging Status Indicator (STAT)
        3. 8.3.9.3 Interrupt to Host
      10. 8.3.10 Input Current Limit on ILIM Pin
      11. 8.3.11 Voltage and Current Monitoring
        1. 8.3.11.1 Voltage and Current Monitoring in Boost Mode
          1. 8.3.11.1.1 Input Over-Voltage Protection
          2. 8.3.11.1.2 Input Under-Voltage Protection
          3. 8.3.11.1.3 System Over-Voltage Protection
          4. 8.3.11.1.4 System Over-Current Protection
        2. 8.3.11.2 Voltage and Current Monitoring in OTG Buck Mode
          1. 8.3.11.2.1 VBUS Over-voltage Protection
          2. 8.3.11.2.2 VBUS Over-Current Protection
      12. 8.3.12 Thermal Regulation and Thermal Shutdown
        1. 8.3.12.1 Thermal Protection in Boost Mode
        2. 8.3.12.2 Thermal Protection in OTG Buck Mode
      13. 8.3.13 Battery Protection
        1. 8.3.13.1 Battery Over-Voltage Protection (BATOVP)
        2. 8.3.13.2 Battery Over-Discharge Protection
      14. 8.3.14 Serial Interface
        1. 8.3.14.1 Data Validity
        2. 8.3.14.2 START and STOP Conditions
        3. 8.3.14.3 Byte Format
        4. 8.3.14.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 8.3.14.5 Slave Address and Data Direction Bit
        6. 8.3.14.6 Single Write and Read
        7. 8.3.14.7 Multi-Write and Multi-Read
    4. 8.4 Device Functional Modes
      1. 8.4.1 Host Mode and Default Mode
    5. 8.5 Register Maps
      1. 8.5.1  Battery Voltage Regulation Limit Register (Address = 00h) [reset = A0h]
        1. Table 10. REG00 Register Field Descriptions
      2. 8.5.2  Charger Current Limit Register (Address = 01h) [reset = 5Eh]
        1. Table 11. REG01 Register Field Descriptions
      3. 8.5.3  Input Voltage Limit Register (Address = 02h) [reset = 84h]
        1. Table 12. REG02 Register Field Descriptions
      4. 8.5.4  Input Current Limit Register (Address = 03h) [reset = 39h ]
        1. Table 13. REG03 Register Field Descriptions
      5. 8.5.5  Precharge and Termination Current Limit Register (Address = 04h) [reset = 22h]
        1. Table 14. REG04 Register Field Descriptions
      6. 8.5.6  Charger Control 1 Register (Address = 05h) [reset = 9Dh]
        1. Table 15. REG05 Register Field Descriptions
      7. 8.5.7  Charger Control 2 Register (Address = 06h) [reset = 7Dh]
        1. Table 16. REG06 Register Field Descriptions
      8. 8.5.8  Charger Control 3 Register (Address = 07h) [reset = 02h]
        1. Table 17. REG07 Register Field Descriptions
      9. 8.5.9  Charger Control 4 Register (Address = 08h) [reset = 0Dh]
        1. Table 18. REG08 Register Field Descriptions
      10. 8.5.10 OTG Control Register (Address = 09h) [reset = F6h]
        1. Table 19. REG09 Register Field Descriptions
      11. 8.5.11 ICO Current Limit in Use Register (Address = 0Ah) [reset = XXh]
        1. Table 20. REG0A Register Field Descriptions
      12. 8.5.12 Charger Status 1 Register (Address = 0Bh) [reset = XXh]
        1. Table 21. REG0B Register Field Descriptions
      13. 8.5.13 Charger Status 2 Register (Address = 0Ch) [reset = XXh]
        1. Table 22. REG0C Register Field Descriptions
      14. 8.5.14 NTC Status Register (Address = 0Dh) [reset = 0Xh]
        1. Table 23. REG0D Register Field Descriptions
      15. 8.5.15 FAULT Status Register (Address = 0Eh) [reset = XXh]
        1. Table 24. REG0E Register Field Descriptions
      16. 8.5.16 Charger Flag 1 Register (Address = 0Fh) [reset = 00h]
        1. Table 25. REG0F Register Field Descriptions
      17. 8.5.17 Charger Flag 2 Register (Address = 10h) [reset = 00h]
        1. Table 26. REG10 Register Field Descriptions
      18. 8.5.18 FAULT Flag Register (Address = 11h) [reset = 00h]
        1. Table 27. REG11 Register Field Descriptions
      19. 8.5.19 Charger Mask 1 Register (Address = 12h) [reset = 00h]
        1. Table 28. REG12 Register Field Descriptions
      20. 8.5.20 Charger Mask 2 Register (Address = 13h) [reset = 00h]
        1. Table 29. REG13 Register Field Descriptions
      21. 8.5.21 FAULT Mask Register (Address = 14h) [reset = 00h]
        1. Table 30. REG14 Register Field Descriptions
      22. 8.5.22 ADC Control Register (Address = 15h) [reset = 30h]
        1. Table 31. REG15 Register Field Descriptions
      23. 8.5.23 ADC Function Disable Register (Address = 16h) [reset = 00h]
        1. Table 32. REG16 Register Field Descriptions
      24. 8.5.24 IBUS ADC 1 Register (Address = 17h) [reset = 00h]
        1. Table 33. REG17 Register Field Descriptions
      25. 8.5.25 IBUS ADC 0 Register (Address = 18h) [reset = 00h]
        1. Table 34. REG18 Register Field Descriptions
      26. 8.5.26 ICHG ADC 1 Register (Address = 19h) [reset = 00h]
        1. Table 35. REG19 Register Field Descriptions
      27. 8.5.27 ICHG ADC 0 Register (Address = 1Ah) [reset = 00h]
        1. Table 36. REG1A Register Field Descriptions
      28. 8.5.28 VBUS ADC 1 Register (Address = 1Bh) [reset = 00h]
        1. Table 37. REG1B Register Field Descriptions
      29. 8.5.29 VBUS ADC 0 Register (Address = 1Ch) [reset = 00h]
        1. Table 38. REG1C Register Field Descriptions
      30. 8.5.30 VBAT ADC 1 Register (Address = 1Dh) [reset = 00h]
        1. Table 39. REG1D Register Field Descriptions
      31. 8.5.31 VBAT ADC 0 Register (Address = 1Eh) [reset = 00h]
        1. Table 40. REG1E Register Field Descriptions
      32. 8.5.32 VSYS ADC 1 Register (Address = 1Fh) [reset = 00h]
        1. Table 41. REG1F Register Field Descriptions
      33. 8.5.33 VSYS ADC 0 Register (Address = 20h) [reset = 00h]
        1. Table 42. REG20 Register Field Descriptions
      34. 8.5.34 TS ADC 1 Register (Address = 21h) [reset = 00h]
        1. Table 43. REG21 Register Field Descriptions
      35. 8.5.35 TS ADC 0 Register (Address = 22h) [reset = 00h]
        1. Table 44. REG22 Register Field Descriptions
      36. 8.5.36 TDIE ADC 1 Register (Address = 23h) [reset = 00h]
        1. Table 45. REG23 Register Field Descriptions
      37. 8.5.37 TDIE ADC 0 Register (Address = 24h) [reset = 00h]
        1. Table 46. REG24 Register Field Descriptions
      38. 8.5.38 Part Information Register (Address = 25h) [reset = 18h]
        1. Table 47. REG25 Register Field Descriptions
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Inductor Selection
        2. 9.2.2.2 Input (VBUS / PMID) Capacitor
        3. 9.2.2.3 Output (VSYS) Capacitor
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12器件和文档支持
    1. 12.1 器件支持
      1. 12.1.1 第三方米6体育平台手机版_好二三四免责声明
    2. 12.2 文档支持
      1. 12.2.1 相关文档
    3. 12.3 接收文档更新通知
    4. 12.4 社区资源
    5. 12.5 商标
    6. 12.6 静电放电警告
    7. 12.7 术语表
  13. 13机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.5 Electrical Characteristics

VVBUS_UVLO_RISING< VVBUS < VVBUS_OV, TJ = -40°C to+125°C, and TJ = 25°C for typical values (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
QUIESCENT CURRENTS
IBAT Battery discharge current (BAT) VBAT = 9 V, No VBUS, SCL, SDA = 0 V or 1.8 V, TJ=25C, ADC Disabled 12 14 µA
VBAT = 9 V, No VBUS, SCL, SDA = 0 V or 1.8 V, TJ < 85C, ADC Disabled 12 20 µA
IVBUS_HIZ Input supply current (VBUS) in HIZ VBUS = 5 V, High-Z Mode, no battery, ADC Disabled, 25℃ 30 38 µA
VBUS = 5 V, High-Z Mode, no battery, ADC Disabled, <85℃ 30 48 µA
IVBUS Input supply current (VBUS) VBUS = 5 V, VBAT = 7.6 V, converter not switching 1.5 3 mA
VBUS = 5 V, VBAT = 7.6 V, converter switching, ISYS = 0A 3 mA
IBAT_OTG Battery discharge current in OTG mode VBAT = 8.4 V, OTG Buck Mode, IVBUS = 0A, converter switching 3 mA
VBUS/VBAT POWER UP
VVBUS_OP VBUS operating range 3.9 6.2 V
VVBUS_UVLO_RISING VBUS rising for active I2C, no battery VBUS rising 3.3 3.65 V
VVBUS_OV VBUS over-voltage rising threshold VBUS rising 6.2 6.6 V
VBUS over-voltage falling threshold VBUS falling 5.9 6.4 V
VBAT_UVLO_RISING Battery for active I2C VBAT rising 3.7 4 4.42 V
VPOORSRC_FALLING Bad adapter detection threshold VBUS falling below VPOORSRC_FALLING 3.7 V
IPOORSRC Bad adapter detection current source 15 mA
VSYS Typical System Regulation Voltage ISYS = 0A, VBAT = 8.80 V > SYS_MIN[3:0], Charge Disabled (EN_CHG = 0) VBAT+0.1 V
ISYS = 0A, VBAT < SYS_MIN[3:0], Charge Disabled (EN_CHG = 0) VSYS_MIN+0.2 V
VSYS_MIN System Regulation Voltage VBAT < SYS_MIN[3:0] = 0010, Charge Disabled (EN_CHG = 0) 6.2 6.4 V
BATTERY CHARGER
VREG_RANGE Typical charge voltage regulation range 6.8 9.2 V
VREG_STEP Typical charge voltage step 10 mV
VREG_ACC Charge voltage VREG = 8.40 V, TJ = 0°C to 85°C, 8.35 8.4 8.44 V
ICHG_RANGE Charge current regulation range 100 2200 mA
ICHG_STEP Charge current regulation step 50 mA
ICHG_ACC Fast Charge current regulation accuracy ICHG = 1000 mA, VBAT = 6.2 V or 7.6 V, TJ = 0°C to 85°C -7.5 7.5 %
ICHG_ACC Fast Charge current regulation accuracy ICHG = 500mA, VBAT = 6.2 V or 7.6 V, TJ = 0°C to 85°C -15 15 %
ICHG_ACC Fast Charge current regulation accuracy ICHG = 250 mA, VBAT = 6.2 V or 7.6 V, TJ = 0°C to 85°C -25 25 %
IPRECHG_RANGE Precharge current range 50 800 mA
IPRECHG_STEP Typical precharge current step 50 mA
IPRECHG_ACC Precharge current accuracy VBAT = 5.2 V, IPRECHG = 200 mA, TJ = 25°C 170 237 mA
VBAT = 5.2 V, IPRECHG = 200 mA, TJ = 0°C to 85°C 150 245 mA
ITERM_RANGE Termination current range 50 800 mA
ITERM_STEP Typical termination current step 50 mA
ITERM_ACC Termination current accuracy ICHG = 1.5A, ITERM = 150 mA, TJ = 25°C 143 157 mA
ICHG = 1.5A, ITERM = 150 mA, TJ = 0°C to 85°C 120 180 mA
ICHG = 1.5A, ITERM = 100 mA, TJ = 25°C 95 107 mA
ICHG = 1.5A, ITERM = 100 mA, TJ = 0°C to 85°C 65 125 mA
VBAT_SHORT_RISING Short Battery Voltage rising threshold
to start pre-charging 		VBAT rising 4.1 4.4 4.7 V
VBAT_SHORT_FALLING Short Battery Voltage falling
threshold to stop pre-charging 		VBAT falling 3.7 4 4.3 V
IBAT_SHORT Low Battery Voltage trickle charging current VBAT < 4.4 V 100 mA
VBAT_LOWV_RISING VBAT LOWV Rising threshold to start fast-charging VBAT rising, VBATLOW = 5.6 V 5.3 5.6 5.9 V
VBAT_LOWV_RISING VBAT LOWV Rising threshold to start fast-charging VBAT rising, VBATLOWV = 6.0 V 5.7 6 6.3 V
VBAT_LOWV_FALLING VBAT LOWV Falling threshold to stop fast-charging VBAT falling, VBATLOW = 5.6 V 4.9 5.2 5.5 V
VBAT_LOWV_FALLING VBAT LOWV Falling threshold to stop fast-charging VBAT falling, VBATLOWV = 6.0 V 5.3 5.6 5.9 V
VRECHG Recharge threshold below VREG  VBAT falling, VRECHG[1:0] = 01 200 mV
VBAT falling, VRECHG[1:0] = 10 300 mV
RON_QHS (Q2) High-side switching MOSFET on-resistance between SW and SYS (Q2) TJ =  25°C 32 34.2 mΩ
TJ = – 40°C to 125°C 32 46.5 mΩ
RON_QLS (Q3) Low-side switching MOSFET on-resistance between SW and GND (Q3) TJ = 25°C 42 45.8 mΩ
TJ = – 40°C to 125°C 42 62.5 mΩ
RON_QBAT (Q4) MOSFET on-resistance between SYS and BAT (Q4) TJ = 25°C 18 18.8 mΩ
TJ = – 40°C - 85°C 18 22.5 mΩ
IBAT_DISCHG BAT Discharge current source VBAT = 8V, EN_BAT_DISCHG = 1 8 11.5 16 mA
INPUT VOLTAGE / CURRENT REGULATION
VINDPM_RANGE Input voltage regulation range 3.9 5.5 V
VINDPM_STEP Input voltage regulation step 100 mV
VINDPM Input voltage limit VINDPM = 3.9 V 3.783 3.9 4.017 V
VINDPM = 4.4 V 4.268 4.4 4.532 V
IINDPM_RANGE Input current regulation range 500 3300 mA
IINDPM_STEP Input current regulation step 100 mA
IINDPM_ACC Input current regulation limit IINDPM = 500 mA 438 469 500 mA
IINDPM = 900 mA 765 832 900 mA
IINDPM = 2500 mA 2125 2312 2500 mA
IINDPM = 3000 mA 2550 2775 3000 mA
KILIM IINMAX = KILIM/RILIM Input Current regulation by ILIM pin = 1.5A 1012 1098 1185 A x Ω
RON_QBLK (Q1) Blocking MOSFET on-resistance between VBUS and PMID (QBLK) TJ = 25°C 33 36.8 mΩ
TJ = – 40°C to 125°C 33 50 mΩ
VD+D-_600MVSRC D+/D- Voltage Source (600 mV) 500 600 700 mV
ID+_10UASRC D+ Current Source (10 µA) VD + = 200 mV, 7 10 14 µA
ID+D-_100UASNK D+/D- Current Sink (100 µA) VD + = 500 mV, 50 100 150 µA
VD+D-_0P325 D+/D- Comparator Threshold for Secondary Detection D + pin Rising 250 400 mV
RD-_19K D- Resistor to Ground (19 kΩ) VD- = 500 mV, 14.25 24.8 kΩ
VD+_0P8 D+ Comparator Threshold for Data Contact Detection D + pin Rising 800 mV
VD+D-_1P2 D+/D- Threshold for  Non-standard adapter 1.05 1.35 V
VD+D-_2P0 D+/D- Comparator Threshold for  Non-standard adapter 1.85 2.15 V
VD+D-_2P8 D+/D- Threshold for  Non-standard adapter 2.55 2.85 V
ID+D-_LKG D+/D- Leakage Current HiZ -1 1 µA
VBAT_OVP_RISING Battery over-voltage rising threshold VBAT rising, as percentage of VREG 102.7 104 105 %
VBAT_OVP_FALLING Battery over-voltage falling threshold VBAT falling, as percentage of VREG 101 102 103.3 %
THERMAL REGULATION AND THERMAL SHUTDOWN
TREG Junction temperature regulation accuracy TREG = 120°C 120 °C
TSHUT_RISING Thermal Shutdown Rising threshold Temperature Increasing 150 °C
Thermal Shutdown Falling threshold Temperature Decreasing 120 °C
JEITA THERMISTOR COMPARATOR (BOOST MODE)
VT1 TS pin voltage rising. T1 (0°C) threshold, Charge suspended below this temperature. As Percentage to REGN 72.75 73.25 73.75 %
VT1_HYS TS pin voltage falling. Charge re-enabled to ICHG/2 and VREG above this temperature As Percentage to REGN 1.3 %
VT2 TS pin voltage rising. T2 (10°C) threshold, charge set to ICHG/2 and VREG below this temperature As Percentage to REGN 67.75 68.25 68.75 %
VT2_HYS TS pin voltage falling. Charge set to ICHG and VREG above this temperature As Percentage to REGN 1.2 %
VT3 TS pin voltage falling. T3 (45°C) threshold, charge set to ICHG and 8.1 V above this temperature. As Percentage to REGN 44.25 44.75 45.25 %
VT3_HYS TS pin voltage rising. Charge set to ICHG and VREG below this temperature As Percentage to REGN 1 %
VT5 TS pin voltage falling. T5 (60°C) threshold, charge suspended above this temperature. As Percentage to REGN 33.875 34.375 34.875 %
VT5_HYS TS pin voltage rising. Charge set to ICHG and 8.1 V below this temperature As Percentage to REGN 1.35 %
VBCOLD0 Cold Temperature Threshold 0, TS pin Voltage Rising Threshold As Percentage to REGN, BCOLD = 0 (Approx. – 10°C w/ 103AT) 76.5 77 77.5 %
VBCOLD0_HYS Cold Temperature Threshold 0, TS pin Voltage Falling Threshold As Percentage to REGN 1 %
VBCOLD1 Cold Temperature Threshold 1, TS pin Voltage Rising Threshold As Percentage to REGN, BCOLD = 1 (Approx. – 20°C w/ 103AT) 79.5 80 80.5 %
VBCOLD1_HYS Cold Temperature Threshold 1, TS pin Voltage Falling Threshold As Percentage to REGN 1 %
VBHOT0 Hot Temperature Threshold 0, TS pin Voltage Falling Threshold As Percentage to REGN, BHOT[1:0] = 01 (Approx. 55°C w/ 103AT) 37.25 37.75 38.25 %
VBHOT0_HYS Hot Temperature Threshold 0, TS pin Voltage Rising Threshold As Percentage to REGN 3 %
VBHOT1 Hot Temperature Threshold 1, TS pin Voltage falling Threshold As Percentage to REGN, BHOT[1:0] = 00 (Approx. 60°C w/ 103AT) 33.875 34.375 34.875 %
VBHOT1_HYS Hot Temperature Threshold 1, TS pin Voltage rising Threshold As Percentage to REGN 3 %
VBHOT2 Hot Temperature Threshold 2, TS pin Voltage falling Threshold As Percentage to REGN, BHOT[1:0] = 10 (Approx. 65°C w/ 103AT) 30.75 31.25 31.75 %
VBHOT2_HY2 Hot Temperature Threshold 2, TS pin Voltage rising Threshold As Percentage to REGN 3 %
BOOST MODE CONVERTER
FSW PWM switching frequency Oscillator frequency 1.35 1.5 1.65 MHz
VOTG_BAT Battery voltage exiting OTG mode VBAT falling 5.85 6 6.15 V
VOTG_RANGE Typical OTG Buck mode voltage regulation range 4.5 5.5 V
VOTG_STEP Typical OTG Buck mode voltage regulation step 100 mV
VOTG_ACC OTG Buck mode voltage regulation accuracy IVBUS = 0A, OTG_VLIM = 5.1 V -3 3 %
IOTG_RANGE Typical OTG Buck mode current regulation range 2 A
IOTG_STEP Typical OTG Buck mode current regulation step 100 mA
IOTG_ACC OTG Buck mode current regulation accuracy OTG_ILIM = 2A -15 -7.5 0 %
IOTG_ACC OTG Buck mode current regulation accuracy OTG_ILIM = 1A -15 -7.5 0 %
VOTG_OVP OTG Buck mode over-voltage threshold 5.8 6 V
REGN LDO
VREGN REGN LDO output voltage VVBUS = 5 V, IREGN = 20 mA 4.7 4.8 5.15 V
IREGN REGN LDO current limit VVBUS = 5 V, VREGN = 3.8 V 50 mA
Analog-to-Digital Converter (ADC)
tADC_CONV Conversion time, each measurement ADC_SAMPLE[1:0] = 11 24 ms
ADC_SAMPLE[1:0] = 10 12 ms
ADC_SAMPLE[1:0] = 01 6 ms
ADC_SAMPLE[1:0] = 00 3 ms
ADCRES Effective resolution ADC_SAMPLE[1:0] = 11 14 15 bits
ADC_SAMPLE[1:0] = 10 13 14 bits
ADC_SAMPLE[1:0] = 01 12 13 bits
ADC_SAMPLE[1:0] = 00 10 12 bits
Integral Nonlinearity 16-bit, Best Fit (Char only) ±6.6 LSB
Differential Nonlinearity 16-bit, No Missing Codes (Char only) ±1 LSB
Offset Error 16-bit, Post-Calibration ±1.8 ±4.2 LSB
Offset Error Drift 16-bit, Post-Calibration 0.02 0.01 LSB/°C
Gain Error 16-bit ±131 ±492 LSB
Gain Error Drift 16-bit 2 4.5 LSB/°C
Effective input resistance 8 MΩ
ADC MEASUREMENT RANGES AND LSB
IBUS_ADC_RANGE ADC BUS current range 0 4 A
IBUS_ADC_LSB ADC BUS current LSB 1 mA
IBAT_ADC_RANGE ADC BAT current range 0 4 A
IBAT_ADC_LSB ADC BAT current LSB 1 mA
VBUS_ADC_RANGE ADC BUS voltage range 0 6.5 V
VBUS_ADC_LSB ADC BUS voltage LSB 1 mV
VSYS_ADC_RANGE ADC SYS voltage range 0 10 V
VSYS_ADC_LSB ADC SYS voltage LSB 1 mV
VBAT_ADC_RANGE ADC BAT voltage range 0 10 V
VBAT_ADC_LSB ADC BAT voltage LSB 1 mV
VCELLTOP_ADC_RANGE ADC MID voltage range 0 5 V
VCELLTOP_ADC_LSB ADC MID voltage LSB 1 mV
VCELLBOT_ADC_RANGE ADC MID voltage range 0 5 V
VCELLBOT_ADC_LSB ADC MID voltage LSB 1 mV
VTS_ADC_RANGE ADC TS voltage range 20 80 %
VTS_ADC_LSB ADC TS voltage LSB 0.098 %
VTDIE_ADC_RANGE ADC Die temperature range 0 150 °C
VTDIE_ADC_LSB ADC Die temperature LSB 0.5 °C
I2C INTERFACE (SCL, SDA)
VIH Input high threshold level, SDA and SCL Pull-up rail 1.8 V 1.3 V
VIL Input low threshold level Pull-up rail 1.8 V 0.4 V
VOL Output low threshold level Sink current = 5 mA 0.4 V
IBIAS High level leakage current Pull-up rail 1.8 V 1 uA
VIH_SDA Input high threshold level, SDA Pull-up rail 1.8 V 1.3 V
VIL_SDA Input low threshold level Pull-up rail 1.8 V 0.4 V
VOL_SDA Output low threshold level Sink current = 5 mA 0.4 V
IBIAS_SDA High level leakage current Pull-up rail 1.8 V 1 uA
VIH_SCL Input high threshold level, SDA Pull-up rail 1.8 V 1.3 V
VIL_SCL Input low threshold level Pull-up rail 1.8 V 0.4 V
VOL_SCL Output low threshold level Sink current = 5 mA 0.4 V
IBIAS_SCL High level leakage current Pull-up rail 1.8 V 1 uA
LOGIC I/O PIN (/CE, PSEL)
VIH Input high threshold level 1.3 V
VIL Input low threshold level 0.4 V
IIN_BIAS High level leakage current Pull-up rail 1.8 V 1 uA
LOGIC O PIN (/INT, /PG, STAT)
VOL Output low threshold level Sink current = 5 mA 0.4 V
IOUT_BIAS High level leakage current Pull-up rail 1.8 V 1 µA
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |