SLUSFQ0 November   2024 BQ27Z758

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configurations and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
      1. 5.5.1 Supply Current
      2. 5.5.2 Common Analog (LDO, LFO, HFO, REF1, REF2, I-WAKE)
      3. 5.5.3 Battery Protection (CHG, DSG)
      4. 5.5.4 Cell Sensing Output (BAT_SP, BAT_SN)
      5. 5.5.5 Gauge Measurements (ADC, CC, Temperature)
      6. 5.5.6 Flash Memory
    6. 5.6 Digital I/O: DC Characteristics
    7. 5.7 Digital I/O: Timing Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  BQ27Z758 Processor
      2. 6.3.2  Battery Parameter Measurements
        1. 6.3.2.1 Coulomb Counter (CC) and Digital Filter
        2. 6.3.2.2 ADC Multiplexer
        3. 6.3.2.3 Analog-to-Digital Converter (ADC)
        4. 6.3.2.4 Internal Temperature Sensor
        5. 6.3.2.5 External Temperature Sensor Support
      3. 6.3.3  Power Supply Control
      4. 6.3.4  ENAB Pin
      5. 6.3.5  Bus Communication Interface
      6. 6.3.6  Low Frequency Oscillator
      7. 6.3.7  High Frequency Oscillator
      8. 6.3.8  1.8-V Low Dropout Regulator
      9. 6.3.9  Internal Voltage References
      10. 6.3.10 Overcurrent in Discharge Protection
      11. 6.3.11 Overcurrent in Charge Protection
      12. 6.3.12 Short-Circuit Current in Discharge Protection
      13. 6.3.13 Primary Protection Features
      14. 6.3.14 Battery Sensing
      15. 6.3.15 Gas Gauging
      16. 6.3.16 Zero Volt Charging (ZVCHG)
      17. 6.3.17 Charge Control Features
      18. 6.3.18 Authentication
    4. 6.4 Device Functional Modes
      1. 6.4.1 Lifetime Logging Features
      2. 6.4.2 Configuration
        1. 6.4.2.1 Coulomb Counting
        2. 6.4.2.2 Cell Voltage Measurements
        3. 6.4.2.3 Auto Calibration
        4. 6.4.2.4 Temperature Measurements
  8. 7 Applications and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 Design Requirements (Default)
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Changing Design Parameters
      3. 7.2.3 Calibration Process
      4. 7.2.4 Gauging Data Updates
        1. 7.2.4.1 Application Curve
  9. 8 Power Supply Requirements
  10. 9 Layout
    1. 9.1 Layout Guidelines
    2. 9.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Third-Party Products Disclaimer
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 Receiving Notification of Documentation Updates
    4. 10.4 Support Resources
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 Glossary
  12. 11Revision History
  13. 12Mechanical, Orderable, and Packaging Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • YAH|15
散热焊盘机械数据 (封装 | 引脚)
订购信息

4 Pin Configurations and Functions

BQ27Z758 Pinout Diagram Figure 4-1 Pinout Diagram
Table 4-1 Pin Functions
PIN DESCRIPTION
NAME NO. TYPE(1)
CHG A1 AO Charge FET (CHG) driver
DSG A2 AO Discharge FET (DSG) driver. Connect a series 10-MΩ typical resistor (RDSG) between DSG pin and PACK+ positive terminal.
PACK A3 IA Pack input voltage sensing pin. Connect a series 5-kΩ typical resistor (RPACK) between PACK pin and PACK+ positive terminal.
VDD B1 P LDO regulator input. Connect a 1-µF typical capacitor (CVDD) between VDD and VSS. Place the capacitor close to the gauge.
BAT B2 IA Battery voltage measurement sense input
BAT_SP B3 OA Cell sense output, positive
BAT_SN C3 OA Cell sense output, negative
TS C1 IA Thermistor input to ADC with internal 18-kΩ pullup resistor
GPO/TS1 C2 I/O General purpose output.
Optional TS1 ADC input channel with internal 18-kΩ pullup resistor
VSS D1 P Device ground
ENAB D2 I Active low digital input with weak internal pullup to VDD. If enabled for ultra-low power SHELF mode, driving this signal low will enable the device to wake up.
SDA D3 I/O Digital input, open drain output for I2C serial data. Use with a typical 10-kΩ pullup resistor.
SCL E3 I/O Digital input, open drain output for I2C serial clock. Use with a typical 10-kΩ pullup resistor.
SRP E1 IA This is the positive analog input pin connected to the internal coulomb-counter peripheral for integrating a small voltage between SRP (positive side) and SRN (negative side).
SRN E2 IA This is the negative analog input pin connected to the internal coulomb-counter peripheral for integrating a small voltage between SRP (positive side) and SRN (negative side).
(1) I/O = Digital input/output, IA = Analog input, AO= Analog output, P = Power connection
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |