ZHCSTD7A December   2021  – November 2023 BQ79631-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 说明（续）
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Measurement System
        1. 8.3.1.1 Voltage Measurement System
          1. 8.3.1.1.1 Main ADC
            1. 8.3.1.1.1.1 VS Voltage Measurements
              1. 8.3.1.1.1.1.1 Analog Front End
              2. 8.3.1.1.1.1.2 VS Channel Measurements
              3. 8.3.1.1.1.1.3 Post-ADC Digital LPF
              4. 8.3.1.1.1.1.4 SRP and SRN Measurements
            2. 8.3.1.1.1.2 Temperature Measurements
              1. 8.3.1.1.1.2.1 DieTemp1 Measurement
              2. 8.3.1.1.1.2.2 GPIOs and TSREF Measurements
            3. 8.3.1.1.1.3 Main ADC Operation Control
              1. 8.3.1.1.1.3.1 Operation Modes and Status
          2. 8.3.1.1.2 AUX ADC
            1. 8.3.1.1.2.1 AUX Voltage Measurements
              1. 8.3.1.1.2.1.1 AUX Analog Front End
              2. 8.3.1.1.2.1.2 AUX Channel Measurements
            2. 8.3.1.1.2.2 AUX Temperature Measurements
              1. 8.3.1.1.2.2.1 DieTemp2 Measurement
              2. 8.3.1.1.2.2.2 AUX GPIO Measurements
            3. 8.3.1.1.2.3 MISC Measurements
            4. 8.3.1.1.2.4 AUX ADC Operation Control
          3. 8.3.1.1.3 Synchronization Between MAIN and AUX ADC Measurements
        2. 8.3.1.2 Current Sense ADC
      2. 8.3.2 OVUV Detection
        1. 8.3.2.1 OVUV Operation Modes
        2. 8.3.2.2 OVUV Control and Status
          1. 8.3.2.2.1 OVUV Control
          2. 8.3.2.2.2 OVUV Status
      3. 8.3.3 Power Supplies
        1. 8.3.3.1 AVAO_REF and AVDD_REF
        2. 8.3.3.2 LDOIN
        3. 8.3.3.3 AVDD
        4. 8.3.3.4 DVDD
        5. 8.3.3.5 CVDD and NEG5V
        6. 8.3.3.6 TSREF
      4. 8.3.4 GPIO Configuration
      5. 8.3.5 Communication, OTP, Diagnostic Control
        1. 8.3.5.1 Communication
          1. 8.3.5.1.1 Serial Interface
            1. 8.3.5.1.1.1 UART Physical Layer
              1. 8.3.5.1.1.1.1 UART Transmitter
              2. 8.3.5.1.1.1.2 UART Receiver
              3. 8.3.5.1.1.1.3 COMM CLEAR
            2. 8.3.5.1.1.2 Command and Response Protocol
              1. 8.3.5.1.1.2.1 Transaction Frame Structure
                1. 8.3.5.1.1.2.1.1 Frame Initialization Byte
                2. 8.3.5.1.1.2.1.2 Device Address Byte
                3. 8.3.5.1.1.2.1.3 Register Address Bytes
                4. 8.3.5.1.1.2.1.4 Data Bytes
                5. 8.3.5.1.1.2.1.5 CRC Bytes
                6. 8.3.5.1.1.2.1.6 Calculating Frame CRC Value
                7. 8.3.5.1.1.2.1.7 Verifying Frame CRC
              2. 8.3.5.1.1.2.2 Transaction Frame Examples
                1. 8.3.5.1.1.2.2.1 Single Device Read/Write
                2. 8.3.5.1.1.2.2.2 Stack Read/Write
                3. 8.3.5.1.1.2.2.3 Broadcast Read/Write
                4. 8.3.5.1.1.2.2.4 Broadcast Write Reverse Direction
          2. 8.3.5.1.2 Daisy-Chain Interface
            1. 8.3.5.1.2.1 Daisy-Chain Transmitter and Receiver Functionality
            2. 8.3.5.1.2.2 Daisy-Chain Protocol
          3. 8.3.5.1.3 Start Communication
            1. 8.3.5.1.3.1 Identify Base and Stack
            2. 8.3.5.1.3.2 Auto-Addressing
              1. 8.3.5.1.3.2.1 Setting Up the Device Addresses
              2. 8.3.5.1.3.2.2 Setting Up COMM_CTRL[STACK_DEV] and [TOP_STACK]
              3. 8.3.5.1.3.2.3 Storing Device Address to OTP
            3. 8.3.5.1.3.3 Synchronize Daisy-Chain DLL
            4. 8.3.5.1.3.4 Ring Communication
          4. 8.3.5.1.4 Communication Timeout
            1. 8.3.5.1.4.1 Short Communication Timeout
            2. 8.3.5.1.4.2 Long Communication Timeout
          5. 8.3.5.1.5 Communication Debug Mode
          6. 8.3.5.1.6 Multidrop Configuration
          7. 8.3.5.1.7 SPI Master
          8. 8.3.5.1.8 SPI Loopback
        2. 8.3.5.2 Fault Handling
          1. 8.3.5.2.1 Fault Status Hierarchy
            1. 8.3.5.2.1.1 Debug Registers
          2. 8.3.5.2.2 Fault Masking and Reset
            1. 8.3.5.2.2.1 Fault Masking
            2. 8.3.5.2.2.2 Fault Reset
          3. 8.3.5.2.3 Fault Signaling
            1. 8.3.5.2.3.1 Fault Status Transmitting in ACTIVE Mode
            2. 8.3.5.2.3.2 Fault Status Transmitting in SLEEP Mode
            3. 8.3.5.2.3.3 Heartbeat and Fault Tone
        3. 8.3.5.3 Nonvolatile Memory
          1. 8.3.5.3.1 OTP Page Status
          2. 8.3.5.3.2 OTP Programming
        4. 8.3.5.4 Diagnostic Control/Status
          1. 8.3.5.4.1 Power Supplies Check
            1. 8.3.5.4.1.1 Power Supply Diagnostic Check
            2. 8.3.5.4.1.2 Power Supply BIST
          2. 8.3.5.4.2 Thermal Shutdown and Warning Check
            1. 8.3.5.4.2.1 Thermal Shutdown
            2. 8.3.5.4.2.2 Thermal Warning
          3. 8.3.5.4.3 Oscillators Watchdog
          4. 8.3.5.4.4 OTP Error Check
            1. 8.3.5.4.4.1 OTP CRC Test and Faults
            2. 8.3.5.4.4.2 OTP Margin Read
            3. 8.3.5.4.4.3 Error Check and Correct (ECC) OTP
          5. 8.3.5.4.5 OVUV Detection Check
            1. 8.3.5.4.5.1 Parity Check
            2. 8.3.5.4.5.2 OVUV DAC Check
            3. 8.3.5.4.5.3 OVUV Protector BIST
          6. 8.3.5.4.6 Diagnostic Through ADC Comparison
            1. 8.3.5.4.6.1 VS Voltage Measurement Check
            2. 8.3.5.4.6.2 Temperature Measurement Check
            3. 8.3.5.4.6.3 VS and AUX Open Wire Check
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power Modes
        1. 8.4.1.1 SHUTDOWN Mode
          1. 8.4.1.1.1 Exit SHUTDOWN Mode
          2. 8.4.1.1.2 Enter SHUTDOWN Mode
        2. 8.4.1.2 SLEEP Mode
          1. 8.4.1.2.1 Exit SLEEP Mode
          2. 8.4.1.2.2 Enter SLEEP Mode
        3. 8.4.1.3 ACTIVE Mode
          1. 8.4.1.3.1 Exit ACTIVE Mode
          2. 8.4.1.3.2 Enter ACTIVE Mode From SHUTDOWN Mode
          3. 8.4.1.3.3 Enter ACTIVE Mode From SLEEP Mode
      2. 8.4.2 Device Reset
      3. 8.4.3 Ping and Tone
        1. 8.4.3.1 Ping
        2. 8.4.3.2 Tone
        3. 8.4.3.3 Ping and Tone Propagation
    5. 8.5 Register Maps
      1. 8.5.1 OTP Shadow Register Summary
      2. 8.5.2 Read/Write Register Summary
      3. 8.5.3 Read-Only Register Summary
      4. 8.5.4 Register Field Descriptions
        1. 8.5.4.1  Device Addressing Setup
          1. 8.5.4.1.1 DIR0_ADDR_OTP
          2. 8.5.4.1.2 DIR1_ADDR_OTP
          3. 8.5.4.1.3 CUST_MISC1 through CUST_MISC8
          4. 8.5.4.1.4 DIR0_ADDR
          5. 8.5.4.1.5 DIR1_ADDR
        2. 8.5.4.2  Device ID and Scratch Pad
          1. 8.5.4.2.1 PARTID
          2. 8.5.4.2.2 DEV_REVID
          3. 8.5.4.2.3 DIE_ID1 through DIE_ID9
        3. 8.5.4.3  General Configuration and Control
          1. 8.5.4.3.1  DEV_CONF
          2. 8.5.4.3.2  PWR_TRANSIT_CONF
          3. 8.5.4.3.3  COMM_TIMEOUT_CONF
          4. 8.5.4.3.4  TX_HOLD_OFF
          5. 8.5.4.3.5  STACK_RESPONSE
          6. 8.5.4.3.6  COMM_CTRL
          7. 8.5.4.3.7  CONTROL1
          8. 8.5.4.3.8  CONTROL2
          9. 8.5.4.3.9  CUST_CRC_HI
          10. 8.5.4.3.10 CUST_CRC_LO
          11. 8.5.4.3.11 CUST_CRC_RSLT_HI
          12. 8.5.4.3.12 CUST_CRC_RSLT_LO
        4. 8.5.4.4  Operation Status
          1. 8.5.4.4.1 DIAG_STAT
          2. 8.5.4.4.2 ADC_STAT1
          3. 8.5.4.4.3 ADC_STAT2
          4. 8.5.4.4.4 GPIO_STAT
          5. 8.5.4.4.5 DEV_STAT
        5. 8.5.4.5  ADC Configuration and Control
          1. 8.5.4.5.1  ADC_CONF1
          2. 8.5.4.5.2  ADC_CONF2
          3. 8.5.4.5.3  MAIN_ADC_CAL1
          4. 8.5.4.5.4  MAIN_ADC_CAL2
          5. 8.5.4.5.5  AUX_ADC_CAL1
          6. 8.5.4.5.6  AUX_ADC_CAL2
          7. 8.5.4.5.7  CS_ADC_CAL1
          8. 8.5.4.5.8  CS_ADC_CAL2
          9. 8.5.4.5.9  ADC_CTRL1
          10. 8.5.4.5.10 ADC_CTRL2
          11. 8.5.4.5.11 ADC_CTRL3
        6. 8.5.4.6  ADC Measurement Results
          1. 8.5.4.6.1  VS16_HI/LO
          2. 8.5.4.6.2  VS15_HI/LO
          3. 8.5.4.6.3  VS14_HI/LO
          4. 8.5.4.6.4  VS13_HI/LO
          5. 8.5.4.6.5  VS12_HI/LO
          6. 8.5.4.6.6  VS11_HI/LO
          7. 8.5.4.6.7  VS10_HI/LO
          8. 8.5.4.6.8  VS9_HI/LO
          9. 8.5.4.6.9  VS8_HI/LO
          10. 8.5.4.6.10 VS7_HI/LO
          11. 8.5.4.6.11 VS6_HI/LO
          12. 8.5.4.6.12 VS5_HI/LO
          13. 8.5.4.6.13 VS4_HI/LO
          14. 8.5.4.6.14 VS3_HI/LO
          15. 8.5.4.6.15 VS2_HI/LO
          16. 8.5.4.6.16 VS1_HI/LO
          17. 8.5.4.6.17 CSAUX_HI/LO
          18. 8.5.4.6.18 TSREF_HI/LO
          19. 8.5.4.6.19 GPIO1_HI/LO
          20. 8.5.4.6.20 GPIO2_HI/LO
          21. 8.5.4.6.21 GPIO3_HI/LO
          22. 8.5.4.6.22 GPIO4_HI/LO
          23. 8.5.4.6.23 GPIO5_HI/LO
          24. 8.5.4.6.24 GPIO6_HI/LO
          25. 8.5.4.6.25 GPIO7_HI/LO
          26. 8.5.4.6.26 GPIO8_HI/LO
          27. 8.5.4.6.27 DIETEMP1_HI/LO
          28. 8.5.4.6.28 DIETEMP2_HI/LO
          29. 8.5.4.6.29 AUX_IN_HI/LO
          30. 8.5.4.6.30 AUX_GPIO_HI/LO
          31. 8.5.4.6.31 AUX_PWR_HI/LO
          32. 8.5.4.6.32 AUX_REFL_HI/LO
          33. 8.5.4.6.33 AUX_VBG2_HI/LO
          34. 8.5.4.6.34 AUX_AVAO_REF_HI/LO
          35. 8.5.4.6.35 AUX_AVDD_REF_HI/LO
          36. 8.5.4.6.36 AUX_OV_DAC_HI/LO
          37. 8.5.4.6.37 AUX_UV_DAC_HI/LO
          38. 8.5.4.6.38 AUX_VCM1_HI/LO
          39. 8.5.4.6.39 REFH_HI/LO
          40. 8.5.4.6.40 DIAG_MAIN_HI/LO
          41. 8.5.4.6.41 DIAG_AUX_HI/LO
          42. 8.5.4.6.42 CURRENT_HI/MID/LO
        7. 8.5.4.7  Protector Configuration and Control
          1. 8.5.4.7.1 OV_THRESH
          2. 8.5.4.7.2 UV_THRESH
          3. 8.5.4.7.3 UV_DISABLE1
          4. 8.5.4.7.4 UV_DISABLE2
          5. 8.5.4.7.5 OVUV_CTRL
        8. 8.5.4.8  GPIO Configuration
          1. 8.5.4.8.1 GPIO_CONF1
          2. 8.5.4.8.2 GPIO_CONF2
          3. 8.5.4.8.3 GPIO_CONF3
          4. 8.5.4.8.4 GPIO_CONF4
        9. 8.5.4.9  SPI Master
          1. 8.5.4.9.1 SPI_CONF
          2. 8.5.4.9.2 SPI_EXE
          3. 8.5.4.9.3 SPI_TX3, SPI_TX2, and SPI_TX1
          4. 8.5.4.9.4 SPI_RX3, SPI_RX2, and SPI_RX1
        10. 8.5.4.10 Diagnostic Control
          1. 8.5.4.10.1 DIAG_OTP_CTRL
          2. 8.5.4.10.2 DIAG_COMM_CTRL
          3. 8.5.4.10.3 DIAG_PWR_CTRL
          4. 8.5.4.10.4 DIAG_COMP_CTRL1
          5. 8.5.4.10.5 DIAG_COMP_CTRL2
          6. 8.5.4.10.6 DIAG_COMP_CTRL3
          7. 8.5.4.10.7 DIAG_COMP_CTRL4
          8. 8.5.4.10.8 DIAG_PROT_CTRL
        11. 8.5.4.11 Fault Configuration and Reset
          1. 8.5.4.11.1 FAULT_MSK1
          2. 8.5.4.11.2 FAULT_MSK2
          3. 8.5.4.11.3 FAULT_RST1
          4. 8.5.4.11.4 FAULT_RST2
        12. 8.5.4.12 Fault Status
          1. 8.5.4.12.1  FAULT_SUMMARY
          2. 8.5.4.12.2  FAULT_COMM1
          3. 8.5.4.12.3  FAULT_COMM2
          4. 8.5.4.12.4  FAULT_COMM3
          5. 8.5.4.12.5  FAULT_OTP
          6. 8.5.4.12.6  FAULT_SYS
          7. 8.5.4.12.7  FAULT_PROT1
          8. 8.5.4.12.8  FAULT_PROT2
          9. 8.5.4.12.9  FAULT_OV1
          10. 8.5.4.12.10 FAULT_OV2
          11. 8.5.4.12.11 FAULT_UV1
          12. 8.5.4.12.12 FAULT_UV2
          13. 8.5.4.12.13 FAULT_COMP_GPIO
          14. 8.5.4.12.14 FAULT_COMP_VSAUX1
          15. 8.5.4.12.15 FAULT_COMP_VSAUX2
          16. 8.5.4.12.16 FAULT_COMP_VSOW1
          17. 8.5.4.12.17 FAULT_COMP_VSOW2
          18. 8.5.4.12.18 FAULT_COMP_AUXOW1
          19. 8.5.4.12.19 FAULT_COMP_AUXOW2
          20. 8.5.4.12.20 FAULT_COMP_MISC
          21. 8.5.4.12.21 FAULT_PWR1
          22. 8.5.4.12.22 FAULT_PWR2
          23. 8.5.4.12.23 FAULT_PWR3
        13. 8.5.4.13 Debug Control and Status
          1. 8.5.4.13.1  DEBUG_CTRL_UNLOCK
          2. 8.5.4.13.2  DEBUG_COMM_CTRL1
          3. 8.5.4.13.3  DEBUG_COMM_CTRL2
          4. 8.5.4.13.4  DEBUG_COMM_STAT
          5. 8.5.4.13.5  DEBUG_UART_RC
          6. 8.5.4.13.6  DEBUG_UART_RR_TR
          7. 8.5.4.13.7  DEBUG_COMH_BIT
          8. 8.5.4.13.8  DEBUG_COMH_RC
          9. 8.5.4.13.9  DEBUG_COMH_RR_TR
          10. 8.5.4.13.10 DEBUG_COML_BIT
          11. 8.5.4.13.11 DEBUG_COML_RC
          12. 8.5.4.13.12 DEBUG_COML_RR_TR
          13. 8.5.4.13.13 DEBUG_UART_DISCARD
          14. 8.5.4.13.14 DEBUG_COMH_DISCARD
          15. 8.5.4.13.15 DEBUG_COML_DISCARD
          16. 8.5.4.13.16 DEBUG_UART_VALID_HI/LO
          17. 8.5.4.13.17 DEBUG_COMH_VALID_HI/LO
          18. 8.5.4.13.18 DEBUG_COML_VALID_HI/LO
          19. 8.5.4.13.19 DEBUG_OTP_SEC_BLK
          20. 8.5.4.13.20 DEBUG_OTP_DED_BLK
        14. 8.5.4.14 OTP Programming Control and Status
          1. 8.5.4.14.1 OTP_PROG_UNLOCK1A through OTP_PROG_UNLOCK1D
          2. 8.5.4.14.2 OTP_PROG_UNLOCK2A through OTP_PROG_UNLOCK2D
          3. 8.5.4.14.3 OTP_PROG_CTRL
          4. 8.5.4.14.4 OTP_ECC_TEST
          5. 8.5.4.14.5 OTP_ECC_DATAIN1 through OTP_ECC_DATAIN9
          6. 8.5.4.14.6 OTP_ECC_DATAOUT1 through OTP_ECC_DATAOUT9
          7. 8.5.4.14.7 OTP_PROG_STAT
          8. 8.5.4.14.8 OTP_CUST1_STAT
          9. 8.5.4.14.9 OTP_CUST2_STAT
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Base Device Application Circuit
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1  PACK+ and FUSE Measurement
          2. 9.2.1.2.2  Insulation Measurement
          3. 9.2.1.2.3  LINK+/- Measurement
          4. 9.2.1.2.4  CHARGE+/– Measurement
          5. 9.2.1.2.5  Overcurrent Detection Scheme Using OVUV Comparators
          6. 9.2.1.2.6  Unused Pins
          7. 9.2.1.2.7  Current Sense Input
          8. 9.2.1.2.8  VPWR and External NPN
          9. 9.2.1.2.9  Power Supplies, Reference Input
          10. 9.2.1.2.10 GPIO For Thermistor Inputs
          11. 9.2.1.2.11 UART, NFAULT
          12. 9.2.1.2.12 Daisy-Chain Isolation
            1. 9.2.1.2.12.1 Devices Connected on the Same PCB
            2. 9.2.1.2.12.2 Devices Connected on Different PCBs
        3. 9.2.1.3 Application Curve
      2. 9.2.2 Daisy Device Application Circuit
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Ground Planes
      2. 11.1.2 Bypass Capacitors for Power Supplies and Reference
      3. 11.1.3 Voltage Sensing
      4. 11.1.4 Daisy-Chain Communication
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 第三方米6体育平台手机版_好二三四免责声明
    2. 12.2 接收文档更新通知
    3. 12.3 支持资源
    4. 12.4 Trademarks
    5. 12.5 静电放电警告
    6. 12.6 术语表
  14. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6 Pin Configuration and Functions

GUID-20210809-SS0I-PKVP-QGFG-ZNRXW8NBFDCF-low.svg Figure 6-1 PAP Package 64-Pin HTQFP Top View
Table 6-1 Pin Functions
PIN TYPE DESCRIPTION
NAME NO.
VPWR 1 P Power supply input
NPNB 48 P Connect to the base of an external NPN transistor.
LDOIN 47 P 6-V preregulated analog power supply input/sense pin. Connect to the emitter of the external NPN transistor and connect a 0.1-µF decoupling capacitor to AVSS.
AVDD 38 P 5-V regulated output. AVDD supplies the internal analog circuits. Bypass AVDD with a capacitor to AVSS.
AVSS 39 GND Analog ground. Ground connection for internal analog circuits. Connect DVSS, CVSS, REFHM, and AVSS externally. All ground pins must not be left unconnected.
NEG5V 44 P Negative 5-V charge pump used for daisy-chain and Main ADC. Connect with a capacitor to AVSS.
DVDD 49 P 1.8-V regulated output. DVDD supplies the internal digital circuits. Bypass DVDD with a capacitor to DVSS.
DVSS 50 GND Digital ground. Ground connection for internal digital logics. Connect DVSS, CVSS, REFHM, and AVSS externally. All ground pins must not be left unconnected.
CVDD 45 P 5-V daisy-chain communication and I/Os power supply. CVDD supplies the stack daisy-chain communication transceiver circuit and the I/O pins. This power supply also supports an additional 10-mA external load in ACTIVE and SLEEP modes. Bypass CVDD with a capacitor to CVSS.
CVSS 46 GND Daisy-chain communication ground. Ground connection for internal daisy-chain transceivers. Connect DVSS, CVSS, REFHM, and AVSS externally. All ground pins must not be left unconnected.
TSREF 51 P 5-V bias voltage for thermistor. Connect TSREF to the top of the thermistor resistor divider network to the GPIOs when they are configured for thermistor temperature monitoring. Bypass TSREF with a capacitor to AVSS.
REFHP 37 P Precision reference output pin. Bypass with a capacitor to REFHM.
REFHM 36 GND Precision reference ground. Ground connection for the internal precision reference. Connect DVSS, CVSS, REFHM, and AVSS externally. All ground pins must not be left unconnected.
VS16 3 I Differential voltage sense input.
VS15 5 I Differential voltage sense input.
VS14 7 I Differential voltage sense input.
VS13 9 I Differential voltage sense input.
VS12 11 I Differential voltage sense input.
VS11 13 I Differential voltage sense input.
VS10 15 I Differential voltage sense input.
VS9 17 I Differential voltage sense input.
VS8 19 I Differential voltage sense input.
VS7 21 I Differential voltage sense input.
VS6 23 I Differential voltage sense input.
VS5 25 I Differential voltage sense input.
VS4 27 I Differential voltage sense input.
VS3 29 I Differential voltage sense input.
VS2 31 I Differential voltage sense input.
VS1 33 I Differential voltage sense input.
VS0 35 I Differential voltage sense input.
NC 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 NC Unused pin, must be tied to VPWR.
SRP 64 I Current sense input

With SRP and SRN connecting across a low-side shunt resistor, the differential SRP-SRN is measured by current sense ADC.
SRN 63 I Current sense input

With SRP and SRN connecting across a low-side shunt resistor, the differential SRP-SRN is measured by current sense ADC.
RX 52 I UART receiver input. Pullup to CVDD with an external resistor and connect the device RX to the TX output of the host MCU.

If unused (for example for stack devices), connect RX to CVDD.
TX 53 O UART transmitter output. Connect device TX to RX input of the host MCU and shall be pulled up from the host side.

If unused (for example for stack devices), leave it floating.
COMHP 43 I/O Vertical bi-directional communication interface for daisy-chain connection. High-side (north side) differential I/O. Shall connect to the low-side (south side) COMLP and COMLN of the lower adjacent device in the daisy-chain configuration. If unused, connect COMHP and COMHN with a 1-kΩ resistor.
COMHN 42 I/O
COMLP 40 I/O Vertical bi-directional communication interface for daisy-chain connection. Low-side (south side) differential I/O. Shall connect to the high-side (north side) COMHP and COMHN of the upper adjacent device in the daisy-chain configuration. If unused, connect COMHP and COMHN with a 1-kΩ resistor.
COMLN 41 I/O
NFAULT 62 O Fault indication output. Active low.

If used on the base device, pull up NFAULT to CVDD with a pullup resistor and connect NFAULT to host MCU GPIO. If unused, leave it unconnected.
GPIO1 61 I/O General purpose input/output, configuration options are:
  • For external thermistor connection, connect thermistor to the pin and pull up to TSREF. Used as input to ADC.
  • For external DC voltage measurement, configured as input to ADC.
  • Generic digital input/output.
  • Use as I/O for SPI master.
GPIO2 60 I/O
GPIO3 59 I/O
GPIO4 58 I/O
GPIO5 57 I/O
GPIO6 56 I/O
GPIO7 55 I/O
GPIO8 54 I/O
AUX0 34 I Differential voltage sense input.
AUX1 32 I Differential voltage sense input.
AUX2 30 I Differential voltage sense input.
AUX3 28 I Differential voltage sense input.
AUX4 26 I Differential voltage sense input.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |