ZHCSHI1H january   2018  – november 2020 CC1312R

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Functional Block Diagram
  5. 5 Revision History
  6. 6 Device Comparison
  7. 7 Terminal Configuration and Functions
    1. 7.1 Pin Diagram – RGZ Package (Top View)
    2. 7.2 Signal Descriptions – RGZ Package
    3. 7.3 Connections for Unused Pins and Modules
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Power Supply and Modules
    5. 8.5  Power Consumption - Power Modes
    6. 8.6  Power Consumption - Radio Modes
    7. 8.7  Nonvolatile (Flash) Memory Characteristics
    8. 8.8  Thermal Resistance Characteristics
    9. 8.9  RF Frequency Bands
    10. 8.10 861 MHz to 1054 MHz - Receive (RX)
    11. 8.11 861 MHz to 1054 MHz - Transmit (TX) 
    12. 8.12 861 MHz to 1054 MHz - PLL Phase Noise Wideband Mode
    13. 8.13 861 MHz to 1054 MHz - PLL Phase Noise Narrowband Mode
    14. 8.14 359 MHz to 527 MHz - Receive (RX)
    15. 8.15 359 MHz to 527 MHz - Transmit (TX) 
    16. 8.16 359 MHz to 527 MHz - PLL Phase Noise
    17. 8.17 143 MHz to 176 MHz - Receive (RX)
    18. 8.18 143 MHz to 176 MHz  - Transmit (TX) 
    19. 8.19 143 MHz to 176 MHz - PLL Phase Noise
    20. 8.20 Timing and Switching Characteristics
      1. 8.20.1 Reset Timing
      2. 8.20.2 Wakeup Timing
      3. 8.20.3 Clock Specifications
        1. 8.20.3.1 48 MHz Clock Input (TCXO)
        2. 8.20.3.2 48 MHz Crystal Oscillator (XOSC_HF)
        3. 8.20.3.3 48 MHz RC Oscillator (RCOSC_HF)
        4. 8.20.3.4 2 MHz RC Oscillator (RCOSC_MF)
        5. 8.20.3.5 32.768 kHz Crystal Oscillator (XOSC_LF)
        6. 8.20.3.6 32 kHz RC Oscillator (RCOSC_LF)
      4. 8.20.4 Synchronous Serial Interface (SSI) Characteristics
        1. 8.20.4.1 Synchronous Serial Interface (SSI) Characteristics
        2.       43
      5. 8.20.5 UART
        1. 8.20.5.1 UART Characteristics
    21. 8.21 Peripheral Characteristics
      1. 8.21.1 ADC
        1. 8.21.1.1 Analog-to-Digital Converter (ADC) Characteristics
      2. 8.21.2 DAC
        1. 8.21.2.1 Digital-to-Analog Converter (DAC) Characteristics
      3. 8.21.3 Temperature and Battery Monitor
        1. 8.21.3.1 Temperature Sensor
        2. 8.21.3.2 Battery Monitor
      4. 8.21.4 Comparators
        1. 8.21.4.1 Low-Power Clocked Comparator
        2. 8.21.4.2 Continuous Time Comparator
      5. 8.21.5 Current Source
        1. 8.21.5.1 Programmable Current Source
      6. 8.21.6 GPIO
        1. 8.21.6.1 GPIO DC Characteristics
    22. 8.22 Typical Characteristics
      1. 8.22.1 MCU Current
      2. 8.22.2 RX Current
      3. 8.22.3 TX Current
      4. 8.22.4 RX Performance
      5. 8.22.5 TX Performance
      6. 8.22.6 ADC Performance
  9. 9 Detailed Description
    1. 9.1  Overview
    2. 9.2  System CPU
    3. 9.3  Radio (RF Core)
      1. 9.3.1 Proprietary Radio Formats
    4. 9.4  Memory
    5. 9.5  Sensor Controller
    6. 9.6  Cryptography
    7. 9.7  Timers
    8. 9.8  Serial Peripherals and I/O
    9. 9.9  Battery and Temperature Monitor
    10. 9.10 µDMA
    11. 9.11 Debug
    12. 9.12 Power Management
    13. 9.13 Clock Systems
    14. 9.14 Network Processor
  10. 10Application, Implementation, and Layout
    1. 10.1 Reference Designs
    2. 10.2 Junction Temperature Calculation
  11. 11Device and Documentation Support
    1. 11.1 Tools and Software
      1. 11.1.1 SimpleLink™ Microcontroller Platform
    2. 11.2 Documentation Support
    3. 11.3 支持资源
    4. 11.4 Trademarks
    5. 11.5 静电放电警告
    6. 11.6 术语表
  12. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Packaging Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • RGZ|48
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.10 861 MHz to 1054 MHz - Receive (RX)

When measured on the CC1312REM-XD7793 reference design with Tc = 25 °C, VDDS = 3.0 V with
DC/DC enabled unless otherwise noted. All measurements are performed at the antenna input with a combined RX and TX path. All measurements are performed conducted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
General Parameters
Digital channel filter programmable receive bandwidth 4 4000 kHz
Data rate step size 1.5 bps
Spurious emissions 25 MHz to 1 GHz 868 MHz
Conducted emissions measured according to ETSI EN 300 220		 < -57 dBm
Spurious emissions 1 GHz to 13 GHz < -47 dBm
IEEE 802.15.4, 50 kbps, ±25 kHz Deviation, 2-GFSK, 100 kHz RX Bandwidth
Sensitivity BER = 10–2, 868 MHz –110 dBm
Saturation limit BER = 10–2, 868 MHz 10 dBm
Selectivity, ±200 kHz BER = 10–2, 868 MHz(1) 44 dB
Selectivity, ±400 kHz BER = 10–2, 868 MHz(1) 48 dB
Blocking, ±1 MHz BER = 10–2, 868 MHz(1) 57 dB
Blocking, ±2 MHz BER = 10–2, 868 MHz(1) 61 dB
Blocking, ±5 MHz BER = 10–2, 868 MHz(1) 67 dB
Blocking, ±10 MHz BER = 10–2, 868 MHz(1) 76 dB
Image rejection (image compensation enabled) BER = 10–2, 868 MHz(1) 39 dB
RSSI dynamic range Starting from the sensitivity limit  95 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
100 kbps, ±25 kHz Deviation, 2-GFSK, 137 kHz RX Bandwidth 
Sensitivity 100 kbps 1% PER, 127 byte payload, 868 MHz -104 dBm
Selectivity, ±200 kHz 1% PER, 127 byte payload, 868 MHz. Wanted signal at -96 dBm 31 dB
Selectivity, ±400 kHz 1% PER, 127 byte payload, 868 MHz. Wanted signal at -96 dBm 37 dB
Co-channel rejection 1% PER, 127 byte payload, 868 MHz. Wanted signal at -79 dBm -9 dB
200 kbps, ±50 kHz Deviation, 2-GFSK, 311 kHz RX Bandwidth
Sensitivity BER = 10–2, 868 MHz –103 dBm
Sensitivity BER = 10–2, 915 MHz –103 dBm
Selectivity, ±400 kHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 41 dB
Selectivity, ±800 kHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 47 dB
Blocking, ±2 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 55 dB
Blocking, ±10 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 67 dB
500 kbps, ±190 kHz Deviation, 2-GFSK, 1150 kHz RX Bandwidth
Sensitivity 500 kbps 1% PER, 127 byte payload, 915 MHz -94 dBm
Selectivity, ±1 MHz 1% PER, 127 byte payload, 915 MHz. Wanted signal at -88 dBm 14 dB
Selectivity, ±2 MHz 1% PER, 127 byte payload, 915 MHz. Wanted signal at -88 dBm 42 dB
Co-channel rejection 1% PER, 127 byte payload, 915 MHz. Wanted signal at -71 dBm -9 dB
1 Mbps, ±350 kHz Deviation, 2-GFSK, 2.2 MHz RX Bandwidth
Sensitivity BER = 10–2, 868 MHz -97 dBm
Sensitivity BER = 10–2, 915 MHz -96 dBm
Blocking, +2 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 43 dB
Blocking, -2 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 26 dB
Blocking, +10 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 54 dB
Blocking, -10 MHz BER = 10–2, 915 MHz. Wanted signal 3 dB above sensitivity limit. 48 dB
SimpleLink™ Long Range, 2.5/5 kbps (20 ksps), ±5 kHz Deviation, 2-GFSK, 34 kHz RX Bandwidth, FEC = 1:2, DSSS = 1:4/1:2
Sensitivity 2.5 kbps, BER = 10–2 , 868 MHz -121 dBm
Sensitivity 5 kbps, BER = 10–2 , 868 MHz -120 dBm
Saturation limit 2.5 kbps, BER = 10–2 , 868 MHz 10 dBm
Selectivity, ±100 kHz 2.5 kbps, BER = 10–2, 868 MHz(1) 49 dB
Selectivity, ±200 kHz 2.5 kbps, BER = 10–2, 868 MHz(1) 50 dB
Selectivity, ±300 kHz 2.5 kbps, BER = 10–2, 868 MHz(1) 51 dB
Blocking, ±1 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 63 dB
Blocking, ±2 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 68 dB
Blocking, ±5 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 78 dB
Blocking, ±10 MHz 2.5 kbps, BER = 10–2, 868 MHz(1) 88 dB
Image rejection (image compensation enabled) 2.5 kbps, BER = 10–2, 868 MHz(1) 45 dB
RSSI dynamic range Starting from the sensitivity limit  97 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
4.8 kbps, OOK, 39 kHz RX Bandwidth
Sensitivity BER = 10–2, 868 MHz, 38.9 kHz RX bandwidth -115 dBm
Sensitivity BER = 10–2, 915 MHz, 41.0 kHz RX bandwidth -115 dBm
Narrowband, 9.6 kbps, ±2.4 kHz Deviation, 2-GFSK, 17.1 kHz RX Bandwidth
Sensitivity BER = 10–2, 868 MHz -118 dBm
Adjacent Channel Rejection BER = 10–2, 868 MHz. Wanted signal 3 dB above the ETSI reference sensitivity limit (-104.6 dBm). Interferer ±20 kHz 39 dB
Alternate Channel Rejection BER = 10–2, 868 MHz. Wanted signal 3 dB above the ETSI reference sensitivity limit (-104.6 dBm). Interferer ±40 kHz 40 dB
Blocking, ±1 MHz BER = 10–2, 868 MHz. Wanted signal 3 dB above the ETSI reference sensitivity limit (-104.6 dBm). 65 dB
Blocking, ±2 MHz BER = 10–2, 868 MHz. Wanted signal 3 dB above the ETSI reference sensitivity limit (-104.6 dBm). 69 dB
Blocking, ±10 MHz BER = 10–2, 868 MHz. Wanted signal 3 dB above the ETSI reference sensitivity limit (-104.6 dBm). 85 dB
Wi-SUN
Sensitivity 50 kbps, ±12.5 kHz Deviation, 2-GFSK, 68 kHz RX Bandwidth, 868 MHz, 10% PER, 250 byte payload -107 dBm
Sensitivity 100 kbps, ±25 kHz Deviation, 2-GFSK, 135 kHz RX Bandwidth, 868 MHz, 10% PER, 250 byte payload -104 dBm
Sensitivity 100 kbps, ±50 kHz Deviation, 2-GFSK, 196 kHz RX Bandwidth, 920.9 MHz, 10% PER, 250 byte payload -102 dBm
Sensitivity 200 kbps, ±100 kHz Deviation, 2-GFSK, 273 kHz RX Bandwidth, 920.8 MHz, 10% PER, 250 byte payload -99 dBm
WB-DSSS, 30/60/120/240 kbps (480 ksps), ±195 kHz Deviation, 2-GFSK, 622 RX Bandwidth, FEC = 1:2, DSSS = 1:8/1:4/1:2/1:1
Sensitivity 30 kbps, BER = 10–2, 915 MHz -109 dBm
Sensitivity 60 kbps, BER = 10–2, 915 MHz -108 dBm
Sensitivity 120 kbps, BER = 10–2, 915 MHz -106 dBm
Sensitivity 240 kbps, BER = 10–2, 915 MHz -105 dBm
Blocking ±1 MHz 240 kbps, BER = 10–2, 915 MHz 49 dB
Blocking ±2 MHz 240 kbps, BER = 10–2, 915 MHz 53 dB
Blocking ±5 MHz 240 kbps, BER = 10–2, 915 MHz 54 dB
Blocking ±10 MHz 240 kbps, BER = 10–2, 915 MHz 65 dB
(1) Wanted signal 3 dB above the reference sensitivity limit according to ETSI EN 300 220 v. 3.1.1
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |