ZHCSOK7B March   2020  – May 2021 CC3130

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. 功能方框图
  5. Revision History
  6. Device Comparison
    1. 6.1 Related Products
  7. Terminal Configuration and Functions
    1. 7.1 Pin Diagram
    2. 7.2 Pin Attributes
    3. 7.3 Signal Descriptions
      1.      12
    4. 7.4 Connections for Unused Pins
  8. Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Power-On Hours (POH)
    4. 8.4  Recommended Operating Conditions
    5. 8.5  Current Consumption Summary
    6. 8.6  TX Power Control
    7. 8.7  Brownout and Blackout Conditions
      1. 8.7.1 Brownout and Blackout Voltage Levels
    8. 8.8  Electrical Characteristics for DIO Pins
      1. 8.8.1 Electrical Characteristics: DIO Pins Except 52 and 53
      2. 8.8.2 Electrical Characteristics: DIO Pins 52 and 53
    9. 8.9  Electrical Characteristics for Pin Internal Pullup and Pulldown
    10. 8.10 WLAN Receiver Characteristics
      1.      28
    11. 8.11 WLAN Transmitter Characteristics
      1.      30
    12. 8.12 WLAN Transmitter Out-of-Band Emissions
      1. 8.12.1 WLAN 2.4 GHz Filter Requirements
    13. 8.13 BLE/2.4 GHz Radio Coexistence and WLAN Coexistence Requirements
    14. 8.14 Thermal Resistance Characteristics for RGK Package
    15. 8.15 Timing and Switching Characteristics
      1. 8.15.1 Power Supply Sequencing
      2. 8.15.2 Device Reset
      3. 8.15.3 Reset Timing
        1. 8.15.3.1 nRESET (32-kHz Crystal)
        2. 8.15.3.2 First-Time Power-Up and Reset Removal Timing Requirements (32-kHz Crystal)
        3. 8.15.3.3 nRESET (External 32-kHz Crystal)
          1. 8.15.3.3.1 First-Time Power-Up and Reset Removal Timing Requirements (External 32-kHz Crystal)
      4. 8.15.4 Wakeup From HIBERNATE Mode
        1. 8.15.4.1 nHIB Timing Requirements
      5. 8.15.5 Clock Specifications
        1. 8.15.5.1 Slow Clock Using Internal Oscillator
          1. 8.15.5.1.1 RTC Crystal Requirements
        2. 8.15.5.2 Slow Clock Using an External Clock
          1. 8.15.5.2.1 External RTC Digital Clock Requirements
        3. 8.15.5.3 Fast Clock (Fref) Using an External Crystal
          1. 8.15.5.3.1 WLAN Fast-Clock Crystal Requirements
        4. 8.15.5.4 Fast Clock (Fref) Using an External Oscillator
          1. 8.15.5.4.1 External Fref Clock Requirements (–40°C to +85°C)
      6. 8.15.6 Interfaces
        1. 8.15.6.1 Host SPI Interface Timing
          1. 8.15.6.1.1 Host SPI Interface Timing Parameters
        2. 8.15.6.2 Flash SPI Interface Timing
          1. 8.15.6.2.1 Flash SPI Interface Timing Parameters
        3. 8.15.6.3 DIO Interface Timing
          1. 8.15.6.3.1 DIO Output Transition Time Parameters (Vsupply = 3.3 V)
            1. 8.15.6.3.1.1 DIO Output Transition Times (Vsupply = 3.3 V) (1)
          2. 8.15.6.3.2 DIO Input Transition Time Parameters
            1. 8.15.6.3.2.1 DIO Input Transition Time Parameters
    16. 8.16 External Interfaces
      1. 8.16.1 SPI Flash Interface
      2. 8.16.2 SPI Host Interface
      3. 8.16.3 Host UART Interface
        1. 8.16.3.1 5-Wire UART Topology
        2. 8.16.3.2 4-Wire UART Topology
        3. 8.16.3.3 3-Wire UART Topology
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Device Features
      1. 9.2.1 WLAN
      2. 9.2.2 Network Stack
      3. 9.2.3 Security
      4. 9.2.4 Host Interface and Driver
      5. 9.2.5 System
    3. 9.3 Power-Management Subsystem
      1. 9.3.1 VBAT Wide-Voltage Connection
    4. 9.4 Low-Power Operating Modes
      1. 9.4.1 Low-Power Deep Sleep
      2. 9.4.2 Hibernate
      3. 9.4.3 Shutdown
    5. 9.5 Memory
      1. 9.5.1 External Memory Requirements
    6. 9.6 Restoring Factory Default Configuration
    7. 9.7 Hostless Mode
  10. 10Applications, Implementation, and Layout
    1. 10.1 Application Information
      1. 10.1.1 BLE/2.4 GHz Radio Coexistence
      2. 10.1.2 Antenna Selection
      3. 10.1.3 Typical Application
    2. 10.2 PCB Layout Guidelines
      1. 10.2.1 General PCB Guidelines
      2. 10.2.2 Power Layout and Routing
        1. 10.2.2.1 Design Considerations
      3. 10.2.3 Clock Interface Guidelines
      4. 10.2.4 Digital Input and Output Guidelines
      5. 10.2.5 RF Interface Guidelines
  11. 11Device and Documentation Support
    1. 11.1 Tools and Software
    2. 11.2 Firmware Updates
    3. 11.3 Device Nomenclature
    4. 11.4 Documentation Support
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 术语表
  12. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information
      2. 12.1.2 Tape and Reel Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Current Consumption Summary

TA = 25°C, VBAT = 3.6 V
PARAMETERTEST CONDITIONS(1)(2)MINTYPMAXUNIT
TX1 DSSSTX power level = 0272mA
TX power level = 4188
6 OFDMTX power level = 0248
TX power level = 4179
54 OFDMTX power level = 0223
TX power level = 4160
RX(5)1 DSSS53mA
54 OFDM53
Idle connected(3)690µA
LPDS115µA
Hibernate4µA
Shutdown1µA
Peak calibration current(4)(5)VBAT = 3.6 V420mA
VBAT = 3.3 V450
VBAT = 2.1 V670
TX power level = 0 implies maximum power (see Figure 8-1, Figure 8-2, and Figure 8-3). TX power level = 4 implies output power backed off approximately 4 dB.
The CC3130 system is a constant power-source system. The active current numbers scale based on the VBAT voltage supplied.
DTIM = 1
The complete calibration can take up to 17 mJ of energy from the battery over a time of 24 ms. In default mode, calibration is performed sparingly, and typically occurs when re-enabling the NWP and when the temperature has changed by more than 20°C. There are two additional calibration modes that may be used to reduced or completely eliminate the calibration event. For further details, see CC3x20, CC3x35 SimpleLink™ Wi-Fi® and Internet of Things Network Processor Programmer's Guide.
The RX current is measured with a 1-Mbps throughput rate.