ZHCSOT4B February   2020  – May 2021 CC3230S , CC3230SF

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 功能方框图
  5. 5 Revision History
  6. 6 Device Comparison
    1. 6.1 Related Products
  7. 7 Terminal Configuration and Functions
    1. 7.1 Pin Diagram
    2. 7.2 Pin Attributes
      1. 7.2.1 Pin Descriptions
    3. 7.3 Signal Descriptions
      1.      13
    4. 7.4 Pin Multiplexing
    5. 7.5 Drive Strength and Reset States for Analog and Digital Multiplexed Pins
    6. 7.6 Pad State After Application of Power to Device, Before Reset Release
    7. 7.7 Connections for Unused Pins
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Power-On Hours (POH)
    4. 8.4  Recommended Operating Conditions
    5. 8.5  Current Consumption Summary (CC3230S)
      1.      24
    6. 8.6  Current Consumption Summary (CC3230SF)
      1.      26
    7. 8.7  TX Power Control
    8. 8.8  Brownout and Blackout Conditions
    9. 8.9  Electrical Characteristics for GPIO Pins
      1. 8.9.1 Electrical Characteristics: GPIO Pins Except 29, 30, 50, 52, and 53
      2. 8.9.2 Electrical Characteristics: GPIO Pins 29, 30, 50, 52, and 53
    10. 8.10 Electrical Characteristics for Pin Internal Pullup and Pulldown
      1.      33
    11. 8.11 WLAN Receiver Characteristics
      1.      35
    12. 8.12 WLAN Transmitter Characteristics
      1.      37
    13. 8.13 WLAN Transmitter Out-of-Band Emissions
      1. 8.13.1 WLAN Filter Requirements
    14. 8.14 BLE/2.4 GHz Radio Coexistence and WLAN Coexistence Requirements
    15. 8.15 Thermal Resistance Characteristics for RGK Package
    16. 8.16 Timing and Switching Characteristics
      1. 8.16.1 Power Supply Sequencing
      2. 8.16.2 Device Reset
      3. 8.16.3 Reset Timing
        1. 8.16.3.1 nRESET (32-kHz Crystal)
        2. 8.16.3.2 First-Time Power-Up and Reset Removal Timing Requirements (32-kHz Crystal)
        3. 8.16.3.3 nRESET (External 32-kHz Clock)
          1. 8.16.3.3.1 First-Time Power-Up and Reset Removal Timing Requirements (External 32-kHz Clock)
      4. 8.16.4 Wakeup From HIBERNATE Mode
      5. 8.16.5 Clock Specifications
        1. 8.16.5.1 Slow Clock Using Internal Oscillator
        2. 8.16.5.2 Slow Clock Using an External Clock
          1. 8.16.5.2.1 External RTC Digital Clock Requirements
        3. 8.16.5.3 Fast Clock (Fref) Using an External Crystal
          1. 8.16.5.3.1 WLAN Fast-Clock Crystal Requirements
        4. 8.16.5.4 Fast Clock (Fref) Using an External Oscillator
          1. 8.16.5.4.1 External Fref Clock Requirements (–40°C to +85°C)
      6. 8.16.6 Peripherals Timing
        1. 8.16.6.1  SPI
          1. 8.16.6.1.1 SPI Master
            1. 8.16.6.1.1.1 SPI Master Timing Parameters
          2. 8.16.6.1.2 SPI Slave
            1. 8.16.6.1.2.1 SPI Slave Timing Parameters
        2. 8.16.6.2  I2S
          1. 8.16.6.2.1 I2S Transmit Mode
            1. 8.16.6.2.1.1 I2S Transmit Mode Timing Parameters
          2. 8.16.6.2.2 I2S Receive Mode
            1. 8.16.6.2.2.1 I2S Receive Mode Timing Parameters
        3. 8.16.6.3  GPIOs
          1. 8.16.6.3.1 GPIO Output Transition Time Parameters (Vsupply = 3.3 V)
            1. 8.16.6.3.1.1 GPIO Output Transition Times (Vsupply = 3.3 V) (1) (1)
          2. 8.16.6.3.2 GPIO Input Transition Time Parameters
            1. 8.16.6.3.2.1 GPIO Input Transition Time Parameters
        4. 8.16.6.4  I2C
          1. 8.16.6.4.1 I2C Timing Parameters (1)
        5. 8.16.6.5  IEEE 1149.1 JTAG
          1. 8.16.6.5.1 JTAG Timing Parameters
        6. 8.16.6.6  ADC
          1. 8.16.6.6.1 ADC Electrical Specifications
        7. 8.16.6.7  Camera Parallel Port
          1. 8.16.6.7.1 Camera Parallel Port Timing Parameters
        8. 8.16.6.8  UART
        9. 8.16.6.9  SD Host
        10. 8.16.6.10 Timers
  9. 9 Detailed Description
    1. 9.1  Overview
    2. 9.2  Arm® Cortex®-M4 Processor Core Subsystem
    3. 9.3  Wi-Fi® Network Processor Subsystem
      1. 9.3.1 WLAN
      2. 9.3.2 Network Stack
    4. 9.4  Security
    5. 9.5  Power-Management Subsystem
    6. 9.6  Low-Power Operating Mode
    7. 9.7  Memory
      1. 9.7.1 External Memory Requirements
      2. 9.7.2 Internal Memory
        1. 9.7.2.1 SRAM
        2. 9.7.2.2 ROM
        3. 9.7.2.3 Flash Memory
        4. 9.7.2.4 Memory Map
    8. 9.8  Restoring Factory Default Configuration
    9. 9.9  Boot Modes
      1. 9.9.1 Boot Mode List
    10. 9.10 Hostless Mode
  10. 10Applications, Implementation, and Layout
    1. 10.1 Application Information
      1. 10.1.1 BLE/2.4 GHz Radio Coexistence
      2. 10.1.2 Antenna Selection
      3. 10.1.3 Typical Application
    2. 10.2 PCB Layout Guidelines
      1. 10.2.1 General PCB Guidelines
      2. 10.2.2 Power Layout and Routing
        1. 10.2.2.1 Design Considerations
      3. 10.2.3 Clock Interface Guidelines
      4. 10.2.4 Digital Input and Output Guidelines
      5. 10.2.5 RF Interface Guidelines
  11. 11Device and Documentation Support
    1. 11.1 第三方米6体育平台手机版_好二三四免责声明
    2. 11.2 Tools and Software
    3. 11.3 Firmware Updates
    4. 11.4 Device Nomenclature
    5. 11.5 Documentation Support
    6. 11.6 支持资源
    7. 11.7 Trademarks
    8. 11.8 静电放电警告
    9. 11.9 术语表
  12. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information
      2. 12.1.2 Tape and Reel Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

10.1.2 Antenna Selection

The CC3230x device is designed to also support antenna selection and is controlled from Image Creator. When enabled, there are 3 options possible options:

  • ANT 1: When selected, the GPIOs that are defined for antenna selection with set the RF path for antenna 1.
  • ANT 2: When selected, the GPIOs that are defined for antenna selection will set the RF path for antenna 2.
  • Autoselect: When selected, during a scan and prior to connecting to an AP, CC3230x device will determine the best RF path and select the appropriate antenna (5)(6). The result is the saved as port of the profile.

Figure 10-3 shows the implementation of a complete Bluetooth® low energy and WLAN coexistence network with WLAN and antenna selection. The Coex switch is controlled by a GPIO signal from the BLE device and a GPIO signal from the CC3230x device. The antenna switch is controlled by 2 GPIO lines from the CC3230x device.

GUID-1111B00F-77F9-4215-9FC2-545CB56C052B-low.gifFigure 10-3 Antenna Selection Solution with Coexistence

Figure 10-4 shows the antenna selection implementation for Wi-Fi, with BLE operating on it's own antenna. Note in this implementation no Coex switch is required and only a single GPIO from the BLE device to the CC3230x device is required. The antenna switch is controlled by 2 GPIO lines from the CC3230x device.

GUID-E2342BD3-9213-49C7-8ECC-22984F788AB2-low.gifFigure 10-4 Coexistence Solution with Wi-Fi Antenna Selection and Dedicated BLE Antenna
5. When selecting Autoselect via the API, a reset is required in order for the CC3230x device to determine the best antenna for use.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |