ZHCS065G March   2011  – January 2024 DAC3482

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics – DC Specifications
    6. 5.6  Electrical Characteristics – Digital Specifications
    7. 5.7  Electrical Characteristics – AC Specifications
    8. 5.8  Electrical Characteristics - Phase-Locked Loop Specifications
    9. 5.9  Timing Requirements - Digital Specifications
    10. 5.10 Switching Characteristics – AC Specifications
    11. 5.11 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Serial Interface
      2. 6.3.2  Data Interface
        1. 6.3.2.1 Word-Wide Format
        2. 6.3.2.2 Byte-Wide Format
      3. 6.3.3  Input FIFO
      4. 6.3.4  FIFO Modes of Operation
        1. 6.3.4.1 Dual Sync Source Mode
        2. 6.3.4.2 Single Sync Source Mode
        3. 6.3.4.3 Bypass Mode
      5. 6.3.5  Clocking Modes
        1. 6.3.5.1 PLL Bypass Mode
        2. 6.3.5.2 PLL Mode
      6. 6.3.6  FIR Filters
      7. 6.3.7  Complex Signal Mixer
        1. 6.3.7.1 Full Complex Mixer
        2. 6.3.7.2 Coarse Complex Mixer
        3. 6.3.7.3 Mixer Gain
        4. 6.3.7.4 Real Channel Upconversion
      8. 6.3.8  Quadrature Modulation Correction (QMC)
        1. 6.3.8.1 Gain and Phase Correction
        2. 6.3.8.2 Offset Correction
        3. 6.3.8.3 Group Delay Correction
      9. 6.3.9  Temperature Sensor
      10. 6.3.10 Data Pattern Checker
      11. 6.3.11 Parity Check Test
        1. 6.3.11.1 Word-by-Word Parity
        2. 6.3.11.2 Block Parity
      12. 6.3.12 DAC3482 Alarm Monitoring
      13. 6.3.13 LVPECL Inputs
      14. 6.3.14 LVDS Inputs
      15. 6.3.15 Unused LVDS Port Termination
      16. 6.3.16 CMOS Digital Inputs
      17. 6.3.17 Reference Operation
      18. 6.3.18 DAC Transfer Function
      19. 6.3.19 Analog Current Outputs
    4. 6.4 Device Functional Modes
      1. 6.4.1 Multi-Device Synchronization
        1. 6.4.1.1 Multi-Device Synchronization: PLL Bypassed with Dual Sync Sources Mode
        2. 6.4.1.2 Multi-Device Synchronization: PLL Enabled with Dual Sync Sources Mode
        3. 6.4.1.3 Multi-Device Operation: Single Sync Source Mode
    5. 6.5 Programming
      1. 6.5.1 Power-Up Sequence
      2. 6.5.2 Example Start-Up Routine
        1. 6.5.2.1 Device Configuration
        2. 6.5.2.2 PLL Configuration
        3. 6.5.2.3 NCO Configuration
        4. 6.5.2.4 Example Start-Up Sequence
    6. 6.6 Register Map
      1. 6.6.1 Register Descriptions
        1. 6.6.1.1  Register Name: config0 – Address: 0x00, Default: 0x049C
        2. 6.6.1.2  Register Name: config1 – Address: 0x01, Default: 0x050E
        3. 6.6.1.3  Register Name: config2 – Address: 0x02, Default: 0x7000
        4. 6.6.1.4  Register Name: config3 – Address: 0x03, Default: 0xF000
        5. 6.6.1.5  Register Name: config4 – Address: 0x04, Default: No RESET Value (WRITE TO CLEAR)
        6. 6.6.1.6  Register Name: config5 – Address: 0x05, Default: Setup and Power-Up Conditions Dependent (WRITE TO CLEAR)
        7. 6.6.1.7  Register Name: config6 – Address: 0x06, Default: No RESET Value (READ ONLY)
        8. 6.6.1.8  Register Name: config7 – Address: 0x07, Default: 0xFFFF
        9. 6.6.1.9  Register Name: config8 – Address: 0x08, Default: 0x0000 (CAUSES AUTO-SYNC)
        10. 6.6.1.10 Register Name: config9 – Address: 0x09, Default: 0x8000
        11. 6.6.1.11 Register Name: config10 – Address: 0x0A, Default: 0x0000
        12. 6.6.1.12 Register Name: config11 – Address: 0x0B, Default: 0x0000
        13. 6.6.1.13 Register Name: config12 – Address: 0x0C, Default: 0x0400
        14. 6.6.1.14 Register Name: config13 – Address: 0x0D, Default: 0x0400
        15. 6.6.1.15 Register Name: config14 – Address: 0x0E, Default: 0x0400
        16. 6.6.1.16 Register Name: config15 – Address: 0x0F, Default: 0x0400
        17. 6.6.1.17 Register Name: config16 – Address: 0x10, Default: 0x0000 (CAUSES AUTO-SYNC)
        18. 6.6.1.18 Register Name: config17 – Address: 0x11, Default: 0x0000
        19. 6.6.1.19 Register Name: config18 – Address: 0x12, Default: 0x0000 (CAUSES AUTO-SYNC)
        20. 6.6.1.20 Register Name: config19 – Address: 0x13, Default: 0x0000
        21. 6.6.1.21 Register Name: config20 – Address: 0x14, Default: 0x0000
        22. 6.6.1.22 Register Name: config21 – Address: 0x15, Default: 0x0000
        23. 6.6.1.23 Register name: config22 – Address: 0x16, Default: 0x0000
        24. 6.6.1.24 Register Name: config23 – Address: 0x17, Default: 0x0000
        25. 6.6.1.25 Register Name: config24 – Address: 0x18, Default: NA
        26. 6.6.1.26 Register Name: config25 – Address: 0x19, Default: 0x0440
        27. 6.6.1.27 Register Name: config26 – Address: 0x1A, Default: 0x0020
        28. 6.6.1.28 Register Name: config27 – Address: 0x1B, Default: 0x0000
        29. 6.6.1.29 Register Name: config28 – Address: 0x1C, Default: 0x0000
        30. 6.6.1.30 Register Name: config29 – Address: 0x1D, Default: 0x0000
        31. 6.6.1.31 Register Name: config30 – Address: 0x1E, Default: 0x1111
        32. 6.6.1.32 Register Name: config31 – Address: 0x1F, Default: 0x1140
        33. 6.6.1.33 Register Name: config32 – Address: 0x20, Default: 0x2400
        34. 6.6.1.34 Register Name: config33 – Address: 0x21, Default: 0x0000
        35. 6.6.1.35 Register Name: config34 – Address: 0x22, Default: 0x1B1B
        36. 6.6.1.36 Register Name: config35 – Address: 0x23, Default: 0xFFFF
        37. 6.6.1.37 Register Name: config36 – Address: 0x24, Default: 0x0000
        38. 6.6.1.38 Register Name: config37 – Address: 0x25, Default: 0x7A7A
        39. 6.6.1.39 Register Name: config38 – Address: 0x26, Default: 0xB6B6
        40. 6.6.1.40 Register Name: config39 – Address: 0x27, Default: 0xEAEA
        41. 6.6.1.41 Register Name: config40 – Address: 0x28, Default: 0x4545
        42. 6.6.1.42 Register Name: config41 – Address: 0x29, Default: 0x1A1A
        43. 6.6.1.43 Register Name: config42 – Address: 0x2A, Default: 0x1616
        44. 6.6.1.44 Register Name: config43 – Address: 0x2B, Default: 0xAAAA
        45. 6.6.1.45 Register Name: config44 – Address: 0x2C, Default: 0xC6C6
        46. 6.6.1.46 Register Name: config45 – Address: 0x2D, Default: 0x0004
        47. 6.6.1.47 Register Name: config46 – Address: 0x2E, Default: 0x0000
        48. 6.6.1.48 Register Name: config47 – Address: 0x2F, Default: 0x0000
        49. 6.6.1.49 Register Name: config48 – Address: 0x30, Default: 0x0000
        50. 6.6.1.50 Register Name: version– Address: 0x7F, Default: 0x540C (READ ONLY)
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 IF Based LTE Transmitter
        1. 7.2.1.1 Design Requirements
        2. 7.2.1.2 Detailed Design Procedure
          1. 7.2.1.2.1 Data Input Rate
          2. 7.2.1.2.2 Interpolation
          3. 7.2.1.2.3 LO Feedthrough and Sideband Correction
        3. 7.2.1.3 Application Curves
      2. 7.2.2 Direct Upconversion (Zero IF) LTE Transmitter
        1. 7.2.2.1 Design Requirements
        2. 7.2.2.2 Detailed Design Procedure
          1. 7.2.2.2.1 Data Input Rate
          2. 7.2.2.2.2 Interpolation
          3. 7.2.2.2.3 LO Feedthrough and Sideband Correction
        3. 7.2.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Examples
      3. 7.4.3 Assembly
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Device Nomenclature
        1. 8.1.1.1 Definition of Specifications
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 支持资源
    4. 8.4 Trademarks
    5. 8.5 静电放电警告
    6. 8.6 术语表
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information
    1. 10.1 Clarifications for DAC3482 Power Supply and Phase-Locked Loop Specification

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.3.11 Parity Check Test

The DAC3482 has a parity check test that enables continuous validity monitoring of the data received by the DAC. Parity check testing in combination with the data pattern checker offer an excellent solution for detecting board assembly issues due to missing pad connections.

For the parity check test, an extra parity bit is added to the data bits to make sure the total number of set bits (bits with logic value of 1b) is even or odd. This simple scheme is used to detect data transfer errors. Parity testing is implemented in the DAC3482 in two ways: word-by-word parity and block parity.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |