ZHCS065G March   2011  – January 2024 DAC3482

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics – DC Specifications
    6. 5.6  Electrical Characteristics – Digital Specifications
    7. 5.7  Electrical Characteristics – AC Specifications
    8. 5.8  Electrical Characteristics - Phase-Locked Loop Specifications
    9. 5.9  Timing Requirements - Digital Specifications
    10. 5.10 Switching Characteristics – AC Specifications
    11. 5.11 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Serial Interface
      2. 6.3.2  Data Interface
        1. 6.3.2.1 Word-Wide Format
        2. 6.3.2.2 Byte-Wide Format
      3. 6.3.3  Input FIFO
      4. 6.3.4  FIFO Modes of Operation
        1. 6.3.4.1 Dual Sync Source Mode
        2. 6.3.4.2 Single Sync Source Mode
        3. 6.3.4.3 Bypass Mode
      5. 6.3.5  Clocking Modes
        1. 6.3.5.1 PLL Bypass Mode
        2. 6.3.5.2 PLL Mode
      6. 6.3.6  FIR Filters
      7. 6.3.7  Complex Signal Mixer
        1. 6.3.7.1 Full Complex Mixer
        2. 6.3.7.2 Coarse Complex Mixer
        3. 6.3.7.3 Mixer Gain
        4. 6.3.7.4 Real Channel Upconversion
      8. 6.3.8  Quadrature Modulation Correction (QMC)
        1. 6.3.8.1 Gain and Phase Correction
        2. 6.3.8.2 Offset Correction
        3. 6.3.8.3 Group Delay Correction
      9. 6.3.9  Temperature Sensor
      10. 6.3.10 Data Pattern Checker
      11. 6.3.11 Parity Check Test
        1. 6.3.11.1 Word-by-Word Parity
        2. 6.3.11.2 Block Parity
      12. 6.3.12 DAC3482 Alarm Monitoring
      13. 6.3.13 LVPECL Inputs
      14. 6.3.14 LVDS Inputs
      15. 6.3.15 Unused LVDS Port Termination
      16. 6.3.16 CMOS Digital Inputs
      17. 6.3.17 Reference Operation
      18. 6.3.18 DAC Transfer Function
      19. 6.3.19 Analog Current Outputs
    4. 6.4 Device Functional Modes
      1. 6.4.1 Multi-Device Synchronization
        1. 6.4.1.1 Multi-Device Synchronization: PLL Bypassed with Dual Sync Sources Mode
        2. 6.4.1.2 Multi-Device Synchronization: PLL Enabled with Dual Sync Sources Mode
        3. 6.4.1.3 Multi-Device Operation: Single Sync Source Mode
    5. 6.5 Programming
      1. 6.5.1 Power-Up Sequence
      2. 6.5.2 Example Start-Up Routine
        1. 6.5.2.1 Device Configuration
        2. 6.5.2.2 PLL Configuration
        3. 6.5.2.3 NCO Configuration
        4. 6.5.2.4 Example Start-Up Sequence
    6. 6.6 Register Map
      1. 6.6.1 Register Descriptions
        1. 6.6.1.1  Register Name: config0 – Address: 0x00, Default: 0x049C
        2. 6.6.1.2  Register Name: config1 – Address: 0x01, Default: 0x050E
        3. 6.6.1.3  Register Name: config2 – Address: 0x02, Default: 0x7000
        4. 6.6.1.4  Register Name: config3 – Address: 0x03, Default: 0xF000
        5. 6.6.1.5  Register Name: config4 – Address: 0x04, Default: No RESET Value (WRITE TO CLEAR)
        6. 6.6.1.6  Register Name: config5 – Address: 0x05, Default: Setup and Power-Up Conditions Dependent (WRITE TO CLEAR)
        7. 6.6.1.7  Register Name: config6 – Address: 0x06, Default: No RESET Value (READ ONLY)
        8. 6.6.1.8  Register Name: config7 – Address: 0x07, Default: 0xFFFF
        9. 6.6.1.9  Register Name: config8 – Address: 0x08, Default: 0x0000 (CAUSES AUTO-SYNC)
        10. 6.6.1.10 Register Name: config9 – Address: 0x09, Default: 0x8000
        11. 6.6.1.11 Register Name: config10 – Address: 0x0A, Default: 0x0000
        12. 6.6.1.12 Register Name: config11 – Address: 0x0B, Default: 0x0000
        13. 6.6.1.13 Register Name: config12 – Address: 0x0C, Default: 0x0400
        14. 6.6.1.14 Register Name: config13 – Address: 0x0D, Default: 0x0400
        15. 6.6.1.15 Register Name: config14 – Address: 0x0E, Default: 0x0400
        16. 6.6.1.16 Register Name: config15 – Address: 0x0F, Default: 0x0400
        17. 6.6.1.17 Register Name: config16 – Address: 0x10, Default: 0x0000 (CAUSES AUTO-SYNC)
        18. 6.6.1.18 Register Name: config17 – Address: 0x11, Default: 0x0000
        19. 6.6.1.19 Register Name: config18 – Address: 0x12, Default: 0x0000 (CAUSES AUTO-SYNC)
        20. 6.6.1.20 Register Name: config19 – Address: 0x13, Default: 0x0000
        21. 6.6.1.21 Register Name: config20 – Address: 0x14, Default: 0x0000
        22. 6.6.1.22 Register Name: config21 – Address: 0x15, Default: 0x0000
        23. 6.6.1.23 Register name: config22 – Address: 0x16, Default: 0x0000
        24. 6.6.1.24 Register Name: config23 – Address: 0x17, Default: 0x0000
        25. 6.6.1.25 Register Name: config24 – Address: 0x18, Default: NA
        26. 6.6.1.26 Register Name: config25 – Address: 0x19, Default: 0x0440
        27. 6.6.1.27 Register Name: config26 – Address: 0x1A, Default: 0x0020
        28. 6.6.1.28 Register Name: config27 – Address: 0x1B, Default: 0x0000
        29. 6.6.1.29 Register Name: config28 – Address: 0x1C, Default: 0x0000
        30. 6.6.1.30 Register Name: config29 – Address: 0x1D, Default: 0x0000
        31. 6.6.1.31 Register Name: config30 – Address: 0x1E, Default: 0x1111
        32. 6.6.1.32 Register Name: config31 – Address: 0x1F, Default: 0x1140
        33. 6.6.1.33 Register Name: config32 – Address: 0x20, Default: 0x2400
        34. 6.6.1.34 Register Name: config33 – Address: 0x21, Default: 0x0000
        35. 6.6.1.35 Register Name: config34 – Address: 0x22, Default: 0x1B1B
        36. 6.6.1.36 Register Name: config35 – Address: 0x23, Default: 0xFFFF
        37. 6.6.1.37 Register Name: config36 – Address: 0x24, Default: 0x0000
        38. 6.6.1.38 Register Name: config37 – Address: 0x25, Default: 0x7A7A
        39. 6.6.1.39 Register Name: config38 – Address: 0x26, Default: 0xB6B6
        40. 6.6.1.40 Register Name: config39 – Address: 0x27, Default: 0xEAEA
        41. 6.6.1.41 Register Name: config40 – Address: 0x28, Default: 0x4545
        42. 6.6.1.42 Register Name: config41 – Address: 0x29, Default: 0x1A1A
        43. 6.6.1.43 Register Name: config42 – Address: 0x2A, Default: 0x1616
        44. 6.6.1.44 Register Name: config43 – Address: 0x2B, Default: 0xAAAA
        45. 6.6.1.45 Register Name: config44 – Address: 0x2C, Default: 0xC6C6
        46. 6.6.1.46 Register Name: config45 – Address: 0x2D, Default: 0x0004
        47. 6.6.1.47 Register Name: config46 – Address: 0x2E, Default: 0x0000
        48. 6.6.1.48 Register Name: config47 – Address: 0x2F, Default: 0x0000
        49. 6.6.1.49 Register Name: config48 – Address: 0x30, Default: 0x0000
        50. 6.6.1.50 Register Name: version– Address: 0x7F, Default: 0x540C (READ ONLY)
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 IF Based LTE Transmitter
        1. 7.2.1.1 Design Requirements
        2. 7.2.1.2 Detailed Design Procedure
          1. 7.2.1.2.1 Data Input Rate
          2. 7.2.1.2.2 Interpolation
          3. 7.2.1.2.3 LO Feedthrough and Sideband Correction
        3. 7.2.1.3 Application Curves
      2. 7.2.2 Direct Upconversion (Zero IF) LTE Transmitter
        1. 7.2.2.1 Design Requirements
        2. 7.2.2.2 Detailed Design Procedure
          1. 7.2.2.2.1 Data Input Rate
          2. 7.2.2.2.2 Interpolation
          3. 7.2.2.2.3 LO Feedthrough and Sideband Correction
        3. 7.2.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Examples
      3. 7.4.3 Assembly
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Device Nomenclature
        1. 8.1.1.1 Definition of Specifications
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 支持资源
    4. 8.4 Trademarks
    5. 8.5 静电放电警告
    6. 8.6 术语表
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information
    1. 10.1 Clarifications for DAC3482 Power Supply and Phase-Locked Loop Specification

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.3.12 DAC3482 Alarm Monitoring

The DAC3482 includes a flexible set of alarm monitoring that can be used to alert of a possible malfunction scenario. All the alarm events can be accessed either through the config5 register or through the ALARM pin. Once an alarm is set, the corresponding alarm bit in register config5 must be reset through the serial interface to allow further testing. The set of alarms includes the following conditions

Zero check alarm

  • Alarm_from_zerochk. Occurs when the FIFO write pointer has an all zeros pattern. Since the write pointer is a shift register, all zeros will cause the input pointer to be stuck until the next sync event. When this happens a sync to the FIFO block is required.

FIFO alarms

  • alarm_from_fifo. Occurs when there is a collision in the FIFO pointers or a collision event is close.
    • alarm_fifo_2away. Pointers are within two addresses of each other.
    • alarm_fifo_1away. Pointers are within one address of each other.
    • alarm_fifo_collision. Pointers are equal to each other.

Clock alarms

  • clock_gone. Occurs when either the DACCLK or DATACLOCK have been stopped.
    • alarm_dacclk_gone. Occurs when the DACCLK has been stopped.
    • alarm_dataclk_gone. Occurs when the DATACLK has been stopped.

Pattern checker alarm

  • alarm_from_iotest. Occurs when the input data pattern does not match the pattern key.

PLL alarm

  • alarm_from_pll. Occurs when the PLL is out of lock.

Parity alarms

  • alarm_rparity. Occurs when there is a parity error in the data captured by the rising edge of DATACLKP/N. The PARITYP/N input is the parity bit (word-by-word parity test).
  • alarm_fparity. Occurs when there is a parity error in the data captured by the falling edge of DATACLKP/N. The PARITYP/N input is the parity bit (word-by-word parity test).
  • alarm_frame_parity_err. Occurs when there is a frame parity error when using the FRAME as the parity bit (block parity test).

To prevent unexpected DAC outputs from propagating into the transmit channel chain, the clock and alarm_ fifo_collision alarms can be set in config2 to shut-off the DAC output automatically regardless of the state of TXENABLE or sif_txenable.

Alarm monitoring is implemented as follows:

  • Power up the device using the recommended power-up sequence.
  • Clear all the alarms in config5 by setting them to 0b.
  • Unmask those alarms that will generate a hardware interrupt through the ALARM pin in config7.
  • Enable automatic DAC shut-off in register config2 if required.
  • In the case of an alarm event, the ALARM pin triggers. If automatic DAC shut-off has been enabled, the DAC outputs is disabled.
  • Read registers config5 to determine which alarm triggered the ALARM pin.
  • Correct the error condition and re-synchronize the FIFO.
  • Clear the alarms in config5.
  • Re-read config5 to make sure the alarm event has been corrected.
  • Keep clearing and reading config5 until no error is reported.

For details of alarm monitoring function and behavior, refer to application report SLAA585.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |