ZHCSRN7A January   2023  – September 2023 DAC539G2-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics: Voltage Output
    6. 6.6  Electrical Characteristics: Comparator Mode
    7. 6.7  Electrical Characteristics: General
    8. 6.8  Timing Requirements: I2C Standard Mode
    9. 6.9  Timing Requirements: I2C Fast Mode
    10. 6.10 Timing Requirements: I2C Fast Mode Plus
    11. 6.11 Timing Requirements: SPI Write Operation
    12. 6.12 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 0)
    13. 6.13 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 1)
    14. 6.14 Timing Requirements: GPIO
    15. 6.15 时序图
    16. 6.16 典型特性：电压输出
    17. 6.17 Typical Characteristics: Comparator
    18. 6.18 典型特性：通用
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Smart Digital-to-Analog Converter (DAC) Architecture
      2. 7.3.2 Programming Interface
      3. 7.3.3 Nonvolatile Memory (NVM)
    4. 7.4 Device Functional Modes
      1. 7.4.1 GPI-to-Voltage Converter
        1. 7.4.1.1 Voltage Reference and DAC Transfer Function
        2. 7.4.1.2 Power-Supply as Reference
        3. 7.4.1.3 Internal Reference
        4. 7.4.1.4 External Reference
      2. 7.4.2 Voltage-to-PWM Converter
        1. 7.4.2.1 Function Generation
          1. 7.4.2.1.1 Triangular Waveform Generation
          2. 7.4.2.1.2 Sawtooth Waveform Generation
          3. 7.4.2.1.3 PWM Frequency Correction
      3. 7.4.3 Device Reset and Fault Management
        1. 7.4.3.1 Power-On Reset (POR)
        2. 7.4.3.2 External Reset
        3. 7.4.3.3 Register-Map Lock
        4. 7.4.3.4 NVM Cyclic Redundancy Check (CRC)
          1. 7.4.3.4.1 NVM-CRC-FAIL-USER Bit
          2. 7.4.3.4.2 NVM-CRC-FAIL-INT Bit
      4. 7.4.4 Power-Down Mode
    5. 7.5 Programming
      1. 7.5.1 SPI Programming Mode
      2. 7.5.2 I2C Programming Mode
        1. 7.5.2.1 F/S Mode Protocol
        2. 7.5.2.2 I2C Update Sequence
          1. 7.5.2.2.1 Address Byte
          2. 7.5.2.2.2 Command Byte
        3. 7.5.2.3 I2C Read Sequence
    6. 7.6 Register Maps
      1. 7.6.1  NOP Register (address = 00h) [reset = 0000h]
      2. 7.6.2  DAC-X-VOUT-CMP-CONFIG Register (address = 15h, 03h) [reset = 0400h]
      3. 7.6.3  COMMON-CONFIG Register (address = 1Fh) [reset = 03F9h]
      4. 7.6.4  COMMON-TRIGGER Register (address = 20h) [reset = 0000h]
      5. 7.6.5  FUNCTION-TRIGGER Register (address = 21h) [reset = 0001h]
      6. 7.6.6  GENERAL-STATUS Register (address = 22h) [reset = 2068h]
      7. 7.6.7  DEVICE-MODE-CONFIG Register (address = 25h) [reset = 8040h]
      8. 7.6.8  INTERFACE-CONFIG Register (address = 26h) [reset = 0000h]
      9. 7.6.9  STATE-MACHINE-CONFIG Register (address = 27h) [reset = 0003h]
      10. 7.6.10 SRAM-CONFIG Register (address = 2Bh) [reset = 0000h]
      11. 7.6.11 SRAM-DATA Register (address = 2Ch) [reset = 0000h]
      12. 7.6.12 FUNCTION-CONFIG Register (SRAM address = 20h) [reset = 007Ah]
      13. 7.6.13 FUNCTION-MAX Register (SRAM address = 21h) [reset = B900h]
      14. 7.6.14 FUNCTION-MIN Register (SRAM address = 22h) [reset = 1900h]
      15. 7.6.15 GPI-DEBOUNCE Register (SRAM address = 23h) [reset = 0138h]
      16. 7.6.16 VOUT-DATA-X Register (SRAM address = 24h to 2Bh) [reset = see #GUID-D64978E3-E8F0-4408-A2C1-8C72D24777EC/X6961 ]
      17. 7.6.17 PWM-FREQUENCY-ERROR Register (SRAM address = 9Eh) [reset = device-specific]
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
    2. 9.2 接收文档更新通知
    3. 9.3 支持资源
    4. 9.4 Trademarks
    5. 9.5 静电放电警告
    6. 9.6 术语表
  11. 10Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.4.3.2 External Reset

An external reset to the device is triggered through the register map. To initiate a device software reset event, write the reserved code 0b1010 to the RESET field in the COMMON-TRIGGER register. A software reset initiates a POR event.

千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |