ZHCSIA7 May   2018 DLPA4000

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1.     Device Images
      1.      系统方框图
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 SPI Timing Parameters
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Description
    3. 7.3 Feature Description
      1. 7.3.1 Supply and Monitoring
        1. 7.3.1.1 Supply
        2. 7.3.1.2 Monitoring
          1. 7.3.1.2.1 Block Faults
          2. 7.3.1.2.2 Low Battery and UVLO
          3. 7.3.1.2.3 Thermal Protection
      2. 7.3.2 Illumination
        1. 7.3.2.1 Programmable Gain Block
        2. 7.3.2.2 LDO Illumination
        3. 7.3.2.3 Illumination Driver A
        4. 7.3.2.4 External MOSFETs
          1. 7.3.2.4.1 Gate series resistor (RG)
          2. 7.3.2.4.2 Gate series diode (DG)
          3. 7.3.2.4.3 Gate parallel capacitance (CG)
        5. 7.3.2.5 RGB Strobe Decoder
          1. 7.3.2.5.1 Break Before Make (BBM)
          2. 7.3.2.5.2 Openloop Voltage
          3. 7.3.2.5.3 Transient Current Limit
        6. 7.3.2.6 Illumination Monitoring
          1. 7.3.2.6.1 Power Good
          2. 7.3.2.6.2 RatioMetric Overvoltage Protection
      3. 7.3.3 External Power MOSFET Selection
        1. 7.3.3.1 Threshold Voltage
        2. 7.3.3.2 Gate Charge and Gate Timing
        3. 7.3.3.3 On-resistance RDS(on)
      4. 7.3.4 DMD Supplies
        1. 7.3.4.1 LDO DMD
        2. 7.3.4.2 DMD HV Regulator
        3. 7.3.4.3 DMD/DLPC Buck Converters
        4. 7.3.4.4 DMD Monitoring
          1. 7.3.4.4.1 Power Good
          2. 7.3.4.4.2 Overvoltage Fault
      5. 7.3.5 Buck Converters
        1. 7.3.5.1 LDO Bucks
        2. 7.3.5.2 General Purpose Buck Converters
        3. 7.3.5.3 Buck Converter Monitoring
          1. 7.3.5.3.1 Power Good
          2. 7.3.5.3.2 Overvoltage Fault
      6. 7.3.6 Auxiliary LDOs
      7. 7.3.7 Measurement System
    4. 7.4 Device Functional Modes
    5. 7.5 Programming
      1. 7.5.1 SPI
      2. 7.5.2 Interrupt
      3. 7.5.3 Fast-Shutdown in Case of Fault
      4. 7.5.4 Protected Registers
      5. 7.5.5 Writing to EEPROM
    6. 7.6 Register Maps
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Component Selection for General-Purpose Buck Converters
    3. 8.3 System Example With DLPA4000 Internal Block Diagram
  9. 9 Power Supply Recommendations
    1. 9.1 Power-Up and Power-Down Timing
  10. 10Layout
    1. 10.1 Layout Guidelines
      1. 10.1.1 LED Driver
        1. 10.1.1.1 PowerBlock Gate Control Isolation
        2. 10.1.1.2 VIN to PowerBlocks
        3. 10.1.1.3 Return Current from LEDs and RSense
        4. 10.1.1.4 RC Snubber
        5. 10.1.1.5 Capacitor Choice
      2. 10.1.2 General Purpose Buck 2
      3. 10.1.3 SPI Connections
      4. 10.1.4 RLIM Routing
      5. 10.1.5 LED Connection
    2. 10.2 Layout Example
    3. 10.3 Thermal Considerations
  11. 11器件和文档支持
    1. 11.1 器件支持
      1. 11.1.1 器件命名规则
    2. 11.2 接收文档更新通知
    3. 11.3 社区资源
    4. 11.4 商标
    5. 11.5 静电放电警告
    6. 11.6 术语表
  12. 12机械、封装和可订购信息
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

5 Pin Configuration and Functions

PFD Package
100-Pin HTQFP
Top View
DLPA4000 Pin_out.gif

Pin Functions

PIN I/O DESCRIPTION
N/C 1 — No connect
DRST_LS_IND 2 I/O Connection for the DMD SMPS-inductor (low-side switch).
DRST_5P5V 3 O Filter pin for LDO DMD. Power supply for internal DMD reset regulator, typical 5.5 V.
DRST_PGND 4 GND Power ground for DMD SMPS. Connect to ground plane.
DRST_VIN 5 P Power supply input for LDO DMD. Connect to system power.
DRST_HS_IND 6 I/O Connection for the DMD SMPS-inductor (high-side switch).
ILLUM_5P5 V 7 O Filter pin for LDO ILLUM. Power supply for internal ILLUM block, typical 5.5 V.
ILLUM_VIN 8 P Supply input of LDO ILLUM. Connect to system power.
CH1_SWITCH 9 I Low-side MOSFET switch for LED Cathode. Connect to RGB LED assembly.
CH1_SWITCH 10 I Low-side MOSFET switch for LED Cathode. Connect to RGB LED assembly.
RLIM_1 11 O Connection to LED current sense resistor for CH1 and CH2.
RLIM_BOT_K_2 12 I Kelvin sense connection to ground side of LED current sense resistor.
RLIM_K_2 13 I Kelvin sense connection to top side of current sense resistor.
RLIM_BOT_K_1 14 I Kelvin sense connection to ground side of LED current sense resistor.
RLIM_K_1 15 I Kelvin sense connection to top side of current sense resistor.
RLIM_1 16 O Connection to LED current sense resistor for CH1 and CH2.
CH2_SWITCH 17 I Low-side MOSFET switch for LED cathode. Connect to RGB LED assembly.
CH2_SWITCH 18 I Low-side MOSFET switch for LED cathode. Connect to RGB LED assembly.
CH1_GATE_CTRL 19 O Gate control of CH1 external MOSFET switch for LED cathode.
CH2_GATE_CTRL 20 O Gate control of CH2 external MOSFET switch for LED cathode.
CH3_GATE_CTRL 21 O Gate control of CH3 external MOSFET switch for LED cathode.
RLIM_2 22 O Connection to LED current sense resistor for CH3.
RLIM_2 23 O Connection to LED current sense resistor for CH3.
CH3_SWITCH 24 I Low-side MOSFET switch for LED Cathode. Connect to RGB LED assembly.
CH3_SWITCH 25 I Low-side MOSFET switch for LED Cathode. Connect to RGB LED assembly.
ILLUM_HSIDE_DRIVE 26 O Gate control for external high-side MOSFET for ILLUM Buck converter.
ILLUM_LSIDE_DRIVE 27 O Gate control for external low-side MOSFET for ILLUM Buck converter.
ILLUM_A_BOOST 28 I Supply voltage for high-side N-channel MOSFET gate driver. A 100 nF capacitor (typical) must be connected between this pin and ILLUM_A_SW.
ILLUM_A_FB 29 I Input to the buck converter loop controlling ILED.
ILLUM_A_VIN 30 P Power input to the ILLUM Driver A.
ILLUM_A_SW 31 I/O Switch node connection between high-side NFET and low-side NFET. Serves as common connection for the flying high side MOSFET driver.
ILLUM_A_PGND 32 GND Ground connection to the ILLUM Driver A.
ILLUM_B_BOOST 33 I Supply voltage for high-side N-channel MOSFET gate driver.
ILLUM_B_VIN 34 P Power input to the ILLUM driver B.
ILLUM_B_FB 35 I Input to the buck converter loop controlling ILED.
ILLUM_B_SW 36 I/O Switch node connection between high-side NFET and low-side NFET.
ILLUM_B_PGND 37 GND Ground connection to the ILLUM driver B.
ILLUM_A_COMP1 38 I/O Connection node for feedback loop components
ILLUM_A_COMP2 39 I/O Connection node for feedback loop components
ILLUM_B_COMP1 40 I/O Connection node for feedback loop components
ILLUM_B_COMP2 41 I/O Connection node for feedback loop components
THERMAL_PAD 42 GND Thermal pad. Connect to clean system ground.
CLK_OUT 43 O Color wheel clock output
CW_SPEED_PWM_OUT 44 O Color wheel PWM output
SPI_VIN 45 I Supply for SPI interface
SPI_CLK 46 I SPI clock input
SPI_MISO 47 O SPI data output
SPI_SS_Z 48 I SPI chip select (active low)
SPI_MOSI 49 I SPI data input
PWR7_BOOST 50 I Charge-pump-supply input for the high-side MOSFET gate drive circuit. Connect 100 nF capacitor between PWR7_BOOST and PWR7_SWITCH pins.
PWR7_FB 51 I Converter feedback input. Connect to converter output voltage.
PWR7_VIN 52 P Power supply input for converter.
PWR7_SWITCH 53 I/O Switch node connection between high-side NFET and low-side NFET.
PWR7_PGND 54 GND Ground pin. Power ground return for switching circuit.
ACMPR_LABB_SAMPLE 55 I Control signal to sample voltage at ACMPR_IN_LABB.
PROJ_ON 56 I Input signal to enable/disable the IC and DLP projector.
RESET_Z 57 O Reset output to the DLP system (active low). Pin is held low to reset DLP system.
INT_Z 58 O Interrupt output signal (open drain, active low). Connect to pull-up resistor.
DGND 59 GND Digital ground. Connect to ground plane.
CH_SEL_0 60 I Control signal to enable either of CH1,2,3.
CH_SEL_1 61 I Control signal to enable either of CH1,2,3.
PWR6_PGND 62 GND Ground pin. Power ground return for switching circuit.
PWR6_SWITCH 63 I/O Switch node connection between high-side NFET and low-side NFET.
PWR6_VIN 64 P Power supply input for converter.
PWR6_BOOST 65 I Charge-pump-supply input for the high-side MOSFET gate drive circuit. Connect 100 nF capacitor between PWR6_BOOST and PWR6_SWITCH pins.
PWR6_FB 66 I Converter feedback input. Connect to output voltage.
PWR5_VIN 67 P Power supply input for converter.
PWR5_SWITCH 68 I/O Switch node connection between high-side NFET and low-side NFET.
PWR5_BOOST 69 I Charge-pump-supply input for the high-side MOSFET gate drive circuit. Connect 100nF capacitor between PWR5_BOOST and PWR5_SWITCH pins.
PWR5_PGND 70 GND Ground pin. Power ground return for switching circuit.
PWR5_FB 71 I Converter feedback input. Connect to output voltage.
PWR2_FB 72 I Converter feedback input. Connect to output voltage.
PWR2_PGND 73 GND Ground pin. Power ground return for switching circuit.
PWR2_SWITCH 74 I/O Switch node connection between high-side NFET and low-side NFET.
PWR2_VIN 75 P Power supply input for converter.
PWR2_BOOST 76 I Charge-pump-supply input for the high-side MOSFET gate drive circuit. Connect 100 nF capacitor between PWR2_BOOST and PWR2_SWITCH pins.
ACMPR_IN_1 77 I Input for analog sensor signal.
ACMPR_IN_2 78 I Input for analog sensor signal.
ACMPR_IN_3 79 I Input for analog sensor signal.
ACMPR_IN_LABB 80 I Input for ambient light sensor, sampled input
ACMPR_OUT 81 O Analog comparator out
ACMPR_REF 82 I Reference voltage input for analog comparator
PWR_VIN 83 P Power supply input for LDO_Bucks. Connect to system power.
PWR_5P5V 84 O Filter pin for LDO_BUCKS. Internal analog supply for buck converters, typical 5.5 V.
VINA 85 P Input voltage supply pin for Reference system.
AGND 86 GND Analog ground pin.
PWR3_OUT 87 O Filter pin for LDO_2 DMD/DLPC/AUX, typical 2.5 V.
PWR3_VIN 88 P Power supply input for LDO_2. Connect to system power.
PWR4_OUT 89 O Filter pin for LDO_1 DMD/DLPC/AUX, typical 3.3 V.
PWR4_VIN 90 P Power supply input for LDO_1. Connect to system power.
SUP_2P5V 91 O Filter pin for LDO_V2V5. Internal supply voltage, typical 2.5 V.
SUP_5P0V 92 O Filter pin for LDO_V5V. Internal supply voltage, typical 5 V.
PWR1_PGND 93 GND Ground pin. Power ground return for switching circuit.
PWR1_FB 94 I Converter feedback input. Connect to output voltage.
PWR1_SWITCH 95 I/O Switch node connection between high-side NFET and low-side NFET.
PWR1_VIN 96 P Power supply input for converter.
PWR1_BOOST 97 I Charge-pump-supply input for the high-side MOSFET gate drive circuit. Connect 100nF capacitor between PWR1_BOOST and PWR1_SWITCH pins.
DMD_VOFFSET 98 O VOFS output rail. Connect to ceramic capacitor.
DMD_VBIAS 99 O VBIAS output rail. Connect to ceramic capacitor.
DMD_VRESET 100 O VRESET output rail. Connect to ceramic capacitor.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |