ZHCSCU2E February   2014  – November 2020 DLPC3433 , DLPC3438

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1. 5.1 Test Pins and General Control
    2. 5.2 Parallel Port Input
    3. 5.3 DSI Input Data and Clock
    4. 5.4 DMD Reset and Bias Control
    5. 5.5 DMD Sub-LVDS Interface
    6. 5.6 Peripheral Interface
    7. 5.7 GPIO Peripheral Interface
    8. 5.8 Clock and PLL Support
    9. 5.9 Power and Ground
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Power Electrical Characteristics
    6. 6.6  Pin Electrical Characteristics
    7. 6.7  Internal Pullup and Pulldown Electrical Characteristics
    8. 6.8  DMD Sub-LVDS Interface Electrical Characteristics
    9. 6.9  DMD Low-Speed Interface Electrical Characteristics
    10. 6.10 System Oscillator Timing Requirements
    11. 6.11 Power Supply and Reset Timing Requirements
    12. 6.12 Parallel Interface Frame Timing Requirements
    13. 6.13 Parallel Interface General Timing Requirements
    14. 6.14 BT656 Interface General Timing Requirements
    15. 6.15 DSI Host Timing Requirements
    16. 6.16 Flash Interface Timing Requirements
    17. 6.17 Other Timing Requirements
    18. 6.18 DMD Sub-LVDS Interface Switching Characteristics
    19. 6.19 DMD Parking Switching Characteristics
    20. 6.20 Chipset Component Usage Specification
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Input Source Requirements
        1. 7.3.1.1 Supported Resolution and Frame Rates
        2. 7.3.1.2 3D Display
        3. 7.3.1.3 Parallel Interface
          1. 7.3.1.3.1 PDATA Bus – Parallel Interface Bit Mapping Modes
        4. 7.3.1.4 DSI Interface
      2. 7.3.2 Device Startup
      3. 7.3.3 SPI Flash
        1. 7.3.3.1 SPI Flash Interface
        2. 7.3.3.2 SPI Flash Programming
      4. 7.3.4 I2C Interface
      5. 7.3.5 Content Adaptive Illumination Control (CAIC)
      6. 7.3.6 Local Area Brightness Boost (LABB)
      7. 7.3.7 3D Glasses Operation
      8. 7.3.8 Test Point Support
      9. 7.3.9 DMD Interface
        1. 7.3.9.1 Sub-LVDS (HS) Interface
    4. 7.4 Device Functional Modes
    5. 7.5 Programming
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curve
  9. 9 Power Supply Recommendations
    1. 9.1 PLL Design Considerations
    2. 9.2 System Power-Up and Power-Down Sequence
    3. 9.3 Power-Up Initialization Sequence
    4. 9.4 DMD Fast Park Control (PARKZ)
    5. 9.5 Hot Plug I/O Usage
  10. 10Layout
    1. 10.1 Layout Guidelines
      1. 10.1.1  PLL Power Layout
      2. 10.1.2  Reference Clock Layout
        1. 10.1.2.1 Recommended Crystal Oscillator Configuration
      3. 10.1.3  DSI Interface Layout
      4. 10.1.4  Unused Pins
      5. 10.1.5  DMD Control and Sub-LVDS Signals
      6. 10.1.6  Layer Changes
      7. 10.1.7  Stubs
      8. 10.1.8  Terminations
      9. 10.1.9  Routing Vias
      10. 10.1.10 Thermal Considerations
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 第三方米6体育平台手机版_好二三四免责声明
      2. 11.1.2 Device Nomenclature
        1. 11.1.2.1 Device Markings
        2. 11.1.2.2 Video Timing Parameter Definitions
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
      2. 11.2.2 Related Links
    3. 11.3 接收文档更新通知
    4. 11.4 支持资源
    5. 11.5 Trademarks
    6. 11.6 静电放电警告
    7. 11.7 术语表
  12. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)

6.6 Pin Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER(3) TEST CONDITIONS(4) MIN TYP MAX UNIT
VIH High-level input threshold voltage I2C buffer (I/O type 7) 0.7 × VCC_INTF See  (1) V
I/O type 1, 2, 3, 6, 8 except pins noted in (2) VCC18 = 1.8 V 1.17 3.6
I/O type 1, 6 for pins noted in (2) VCC18 = 1.8 V 1.3 3.6
I/O type 5, 9, 11 VCC_INTF = 1.8 V 1.17 3.6
I/O type 12, 13 VCC_FLSH = 1.8 V 1.17 3.6
I/O type 5, 9, 11 VCC_INTF = 2.5 V 1.7 3.6
I/O type 12, 13 VCC_FLSH = 2.5 V 1.7 3.6
I/O type 5, 9, 11 VCC_INTF = 3.3 V 2.0 3.6
I/O type 12, 13 VCC_FLSH = 3.3 V 2.0 3.6
VIL Low-level input threshold voltage I2C buffer (I/O type 7) –0.5 0.3 × VCC_INTF V
I/O type 1, 2, 3, 6, 8 except pins noted in (2) VCC18 = 1.8 V –0.3 0.63
I/O type 1, 6 for pins noted in (2) VCC18 = 1.8 V –0.3 0.5
I/O type 5, 9, 11 VCC_INTF = 1.8 V –0.3 0.63
I/O type 12, 13 VCC_FLSH = 1.8 V –0.3 0.63
I/O type 5, 9, 11 VCC_INTF = 2.5 V –0.3 0.7
I/O type 12, 13 VCC_FLSH = 2.5 V –0.3 0.7
I/O type 5, 9, 11 VCC_INTF = 3.3 V –0.3 0.8
I/O type 12, 13 VCC_FLSH = 3.3 V –0.3 0.8
VOH High-level output voltage I/O type 1, 2, 3, 6, 8 VCC18 = 1.8 V 1.35 V
I/O type 5, 9, 11 VCC_INTF = 1.8 V 1.35
I/O type 12, 13 VCC_FLSH = 1.8 V 1.35
I/O type 5, 9, 11 VCC_INTF = 2.5 V 1.7
I/O type 12, 13 VCC_FLSH = 2.5 V 1.7
I/O type 5, 9, 11 VCC_INTF = 3.3 V 2.4
I/O type 12, 13 VCC_FLSH = 3.3 V 2.4
VOL Low-level output voltage I2C buffer (I/O type 7) VCC_INTF > 2 V 0.4 V
I2C buffer (I/O type 7) VCC_INTF < 2 V 0.2 × VCC_INTF
I/O type 1, 2, 3, 6, 8 VCC18 = 1.8 V 0.45
I/O type 5, 9, 11 VCC_INTF = 1.8 V 0.45
I/O type 12, 13 VCC_FLSH = 1.8 V 0.45
I/O type 5, 9, 11 VCC_INTF = 2.5 V 0.7
I/O type 12, 13 VCC_FLSH = 2.5 V 0.7
I/O type 5, 9, 11 VCC_INTF = 3.3 V 0.4
I/O type 12, 13 VCC_FLSH = 3.3 V 0.4
over operating free-air temperature range (unless otherwise noted)
PARAMETER(3) TEST CONDITIONS(4) MIN TYP MAX UNIT
IOH High-level output current(5) I/O type 2, 4 VCC18 = 1.8 V 2 mA
I/O type 5 VCC_INTF = 1.8 V 2
I/O type 1 VCC18 = 1.8 V 3.5
I/O type 9 VCC_INTF = 1.8 V 3.5
I/O type 13 VCC_FLSH = 1.8 V 3.5
I/O type 3 VCC18 = 1.8 V 10.6
I/O type 5 VCC_INTF = 2.5 V 5.4
I/O type 9, 13 VCC_INTF = 2.5 V 10.8
I/O type 13 VCC_FLSH = 2.5 V 10.8
I/O type 5 VCC_INTF = 3.3 V 7.8
I/O type 9 VCC_INTF = 3.3 V 15
I/O type 13 VCC_FLSH = 3.3 V 15
IOL Low-level output current(6) I2C buffer (I/O type 7) 3 mA
I/O type 2, 4 VCC18 = 1.8 V 2.3
I/O type 5 VCC_INTF = 1.8 V 2.3
I/O type 1 VCC18 = 1.8 V 4.6
I/O type 9 VCC_INTF = 1.8 V 4.6
I/O type 13 VCC_FLSH = 1.8 V 4.6
I/O type 3 VCC18 = 1.8 V 13.9
I/O type 5 VCC_INTF = 2.5 V 5.2
I/O type 9 VCC_INTF = 2.5 V 10.4
I/O type 13 VCC_FLSH = 2.5 V 10.4
I/O type 5 VCC_INTF = 3.3 V 4.4
I/O type 9 VCC_INTF = 3.3 V 8.9
I/O type 13 VCC_FLSH = 3.3 V 8.9
over operating free-air temperature range (unless otherwise noted)
PARAMETER(3) TEST CONDITIONS(4) MIN TYP MAX UNIT
IOZ High-impedance leakage current I2C buffer (I/O type 7) VI2C buffer < 0.1 × VCC_INTF or
VI2C buffer > 0.9 × VCC_INTF		 –10 10 µA
I/O type 1, 2, 3, 6, 8, VCC18 = 1.8 V –10 10
I/O type 5, 9, 11 VCC_INTF = 1.8 V –10 10
I/O type 12, 13 VCC_FLSH = 1.8 V –10 10
I/O type 5, 9, 11 VCC_INTF = 2.5 V –10 10
I/O type 12, 13 VCC_FLSH = 2.5 V –10 10
I/O type 5, 9, 11 VCC_INTF = 3.3 V –10 10
I/O type 12, 13 VCC_FLSH = 3.3 V –10 10
CI Input capacitance (including package) I2C buffer (I/O type 7) 5 pF
I/O type 1, 2, 3, 6, 8 VCC18 = 1.8 V 2.6 3.5
I/O type 5, 9, 11 VCC_INTF = 1.8 V 2.6 3.5
I/O type 12, 13 VCC_FLSH = 1.8 V 2.6 3.5
I/O type 5, 9, 11 VCC_INTF = 2.5 V 2.6 3.5
I/O type 12, 13 VCC_FLSH = 2.5 V 2.6 3.5
I/O type 5, 9, 11 VCC_INTF = 3.3 V 2.6 3.5
I/O type 12, 13 VCC_FLSH = 3.3 V 2.6 3.5
Sub-LVDS – DMD high speed (I/O type 4) VCC18 = 1.8 V 3
(1) I/O is high voltage tolerant; that is, if VCC_INTF = 1.8 V, the input is 3.3-V tolerant, and if VCC_INTF = 3.3 V, the input is 5-V tolerant.
(2) Controller pins CMP_OUT, PARKZ, RESETZ, and GPIO_00 through GPIO_19 have slightly varied VIH and VIL range from other 1.8-V I/O.
(3) The I/O type refers to the type defined in Table 5-2.
(4) Test conditions that define a value for VCC18, VCC_INTF, or VCC_FLSH show the nominal voltage that the specified I/O's supply reference is set to.
(5) At a high level output signal, the given I/O will be able to output at least the minimum current specified.
(6) At a low level output signal, the given I/O will be able to sink at least the minimum current specified.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |