ZHCSD20H October   2014  – June 2024 DLPC900

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics
    6. 5.6  System Oscillators Timing Requirements #GUID-909D0FD3-84C7-4481-924A-4FDE7EB548A1/DLPS0373944
    7. 5.7  Power-Up and Power-Down Timing Requirements
      1. 5.7.1 Power-Up
      2. 5.7.2 Power-Down
    8. 5.8  JTAG Interface: I/O Boundary Scan Application Timing Requirements
    9. 5.9  JTAG Interface: I/O Boundary Scan Application Switching Characteristics
    10. 5.10 Programmable Output Clocks Switching Characteristics
    11. 5.11 Port 1 and 2 Input Pixel Interface Timing Requirements
    12. 5.12 Two Pixels Per Clock (48-Bit Bus) Timing Requirements
    13. 5.13 Synchronous Serial Port (SSP) Switching Characteristics
    14. 5.14 DMD Interface Switching Characteristics
    15. 5.15 DMD LVDS Interface Switching Characteristics
    16. 5.16 Source Input Blanking Requirements
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 DMD Configurations
      2. 6.3.2 Video Timing Input Blanking Specification
      3. 6.3.3 Board-Level Test Support
      4. 6.3.4 Two Controller Considerations
      5. 6.3.5 Memory Design Considerations
        1. 6.3.5.1 Flash Memory Optimization
        2. 6.3.5.2 Operating Modes
        3. 6.3.5.3 DLPC900 External Memory Space
        4. 6.3.5.4 Minimizing Memory Space
        5. 6.3.5.5 Minimizing Board Size
          1. 6.3.5.5.1 Package Selection
          2. 6.3.5.5.2 Large Density Flash
            1. 6.3.5.5.2.1 Combining Two Chip-Selects with One 32-Megabyte Flash
            2. 6.3.5.5.2.2 Combining Three Chip-Selects with One 64-Megabyte Flash
            3. 6.3.5.5.2.3 Combining Three Chip-Selects with One 128-Megabyte Flash
        6. 6.3.5.6 Minimizing Board Space
        7. 6.3.5.7 Flash Memory
    4. 6.4 Device Functional Modes
      1. 6.4.1 Structured Light Application
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 Typical Two Controller Chipset
        1. 7.2.1.1 Design Requirements
        2. 7.2.1.2 Detailed Design Procedure
          1. 7.2.1.2.1 DLPC900 System Interfaces
            1. 7.2.1.2.1.1 Control Interface
            2. 7.2.1.2.1.2 Input Data Interfaces
            3. 7.2.1.2.1.3 DLPC900 System Output Interfaces
              1. 7.2.1.2.1.3.1 Illumination Interface
              2. 7.2.1.2.1.3.2 Trigger and Sync Interface
            4. 7.2.1.2.1.4 DLPC900 System Support Interfaces
              1. 7.2.1.2.1.4.1 Reference Clock and PLL
              2. 7.2.1.2.1.4.2 Program Memory Flash Interface
              3. 7.2.1.2.1.4.3 DMD Interface
      2. 7.2.2 Typical Single Controller Chipset
  9. 8 Power Supply Recommendations
    1. 8.1 System Power Regulation
      1. 8.1.1 Power Distribution System
        1. 8.1.1.1 1.15V System Power
        2. 8.1.1.2 1.8V System Power
        3. 8.1.1.3 3.3-V System Power
    2. 8.2 System Environment and Defaults
      1. 8.2.1 DLPC900 System Power-Up and Reset Default Conditions
    3. 8.3 System Power-Up Sequence
      1. 8.3.1 Power-On Sense (POSENSE) Support
      2. 8.3.2 Power Good (PWRGOOD) Support
      3. 8.3.3 5V Tolerant Support
    4. 8.4 System Reset Operation
      1. 8.4.1 Power-Up Reset Operation
      2. 8.4.2 System Reset Operation
  10. 9 Layout
    1. 9.1 Layout Guidelines
      1. 9.1.1  General PCB Recommendations
      2. 9.1.2  PCB Layout Guidelines for Internal Controller PLL Power
      3. 9.1.3  PCB Layout Guidelines for Quality Video Performance
      4. 9.1.4  Recommended MOSC Crystal Oscillator Configuration
      5. 9.1.5  Spread Spectrum Clock Generator Support
      6. 9.1.6  GPIO Interface
      7. 9.1.7  General Handling Guidelines for Unused CMOS-Type Pins
      8. 9.1.8  DMD Interface Considerations
        1. 9.1.8.1 Flex Connector Plating
      9. 9.1.9  PCB Design Standards
      10. 9.1.10 Signal Layers
      11. 9.1.11 Trace Widths and Minimum Spacing
      12. 9.1.12 Trace Impedance and Routing Priority
      13. 9.1.13 Power and Ground Planes
      14. 9.1.14 Power Vias
      15. 9.1.15 Decoupling
      16. 9.1.16 Fiducials
    2. 9.2 Layout Example
    3. 9.3 Thermal Considerations
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Device Nomenclature
      2. 10.1.2 Device Markings
      3. 10.1.3 DEFINITIONS—Video Timing Parameters
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 接收文档更新通知
    4. 10.4 支持资源
    5. 10.5 Trademarks
    6. 10.6 静电放电警告
    7. 10.7 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息
7.2.1.2.1.2 Input Data Interfaces

The data interface has a parallel RGB input port and has a nominal I/O voltage of 3.3V. Maximum and minimum input timing specifications for both components are provided in the Interface Timing Requirements. Each parallel RGB port can support up to 24 bits in Video Mode.

Table 7-3 Active Signals – Data Interface
SIGNAL NAMEDESCRIPTION
RGB Parallel Interface Port 1
P1_(A, B, C)_[0:9] (1)24-bit data inputs, 8 bits for each of the red, green, and blue channels. When interfacing to a system with 8 bits per color or less, connect the bus of the red, green, and blue channels to the upper bits of the DLPC900 10-bit bus.
P_CLK1Pixel clock. All input signals on data interface are synchronized with this clock.
P1_VSYNCVertical sync
P1_HSYNCHorizontal sync
P_DATAEN1Input data valid
RGB Parallel Interface Port 2
P2_(A, B, C)_[0:9] (1)24-bit data inputs, 8 bits for each of the red, green, and blue channels. When interfacing to a system with 8 bits per color or less, connect the bus of the red, green, and blue channels to the upper bits of the DLPC900 10-bit bus.
P_CLK2Pixel clock. All input signals on data interface are synchronized with this clock.
P2_VSYNCVertical sync
P2_HSYNCHorizontal sync
P_DATAEN2Input data valid
Optional Pixel Clock 3
P_CLK3Pixel clock. All input signals on data interface are synchronized with this clock.
(1) The A, B, and C input data channels of Port 1 and 2 can be internally swapped for optimum board layout. Refer to the DLPC900 Programmers Guide for details on how to configuring the port settings to match the board layout connections.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |