ZHCSMP1 December   2021 DRV8251

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Device Comparison
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
    7. 7.7 Timing Diagrams
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 External Components
    4. 8.4 Feature Description
      1. 8.4.1 Bridge Control
      2. 8.4.2 Current Regulation
      3. 8.4.3 Protection Circuits
        1. 8.4.3.1 Overcurrent Protection (OCP)
        2. 8.4.3.2 Thermal Shutdown (TSD)
        3. 8.4.3.3 VM Undervoltage Lockout (UVLO)
    5. 8.5 Device Functional Modes
      1. 8.5.1 Active Mode
      2. 8.5.2 Low-Power Sleep Mode
      3. 8.5.3 Fault Mode
    6. 8.6 Pin Diagrams
      1. 8.6.1 Logic-Level Inputs
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Brush DC Motor
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Motor Voltage
          2. 9.2.1.2.2 Motor Current
          3. 9.2.1.2.3 Sense Resistor
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Stall Detection
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
          1. 9.2.2.2.1 Stall Detection Timing
          2. 9.2.2.2.2 Stall Threshold Selection
        3. 9.2.2.3 Application Curves
      3. 9.2.3 Relay Driving
        1. 9.2.3.1 Design Requirements
        2. 9.2.3.2 Detailed Design Procedure
          1. 9.2.3.2.1 Control Interface for Single-Coil Relays
          2. 9.2.3.2.2 Control Interface for Dual-Coil Relays
        3. 9.2.3.3 Application Curves
      4. 9.2.4 Multi-Sourcing with Standard Motor Driver Pinout
    3. 9.3 Current Capability and Thermal Performance
      1. 9.3.1 Power Dissipation and Output Current Capability
      2. 9.3.2 Thermal Performance
        1. 9.3.2.1 Steady-State Thermal Performance
        2. 9.3.2.2 Transient Thermal Performance
  10. 10Power Supply Recommendations
    1. 10.1 Bulk Capacitance
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Community Resources
    4. 12.4 Trademarks
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.5 Electrical Characteristics

4.5 V ≤ VVM ≤ 48 V, –40°C ≤ TJ ≤ 150°C (unless otherwise noted). Typical values are at TJ = 25 °C and VVM = 24 V.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
POWER SUPPLY (VM)
IVMQ VM sleep mode current VVM = 24 V, IN1 = IN2 = 0, TJ = 25°C 1 µA
IVM VM active mode current VVM = 24 V, IN1 = IN2 = 1 3 4 mA
tWAKE Turnon time Control signal to active mode 250 µs
tSLEEP Turnoff time Control signal to sleep mode 0.8 1.5 ms
LOGIC-LEVEL INPUTS (INx)
VIL Input logic low voltage 0.5 V
VIH Input logic high voltage 1.5 V
VHYS Input hysteresis 200 mV
IIL Input logic low current VIN = 0 V -1 1 µA
IIH Input logic high current VIN = 3.3 V 33 100 µA
RPD Input pulldown resistance To GND 100 kΩ
DRIVER OUTPUTS (OUTx)
RDS(on)_HS High-side MOSFET on resistance VVM = 24 V, I = 1 A, fPWM = 25 kHz 225 mΩ
RDS(on)_LS Low-side MOSFET on resistance VVM = 24 V, I = 1 A, fPWM = 25 kHz 225 mΩ
VSD Body diode forward voltage IOUT = 1 A 0.8 V
tRISE Output rise time VVM = 24 V, OUTx rising from 10% to 90% 220 ns
tFALL Output fall time VVM = 24 V, OUTx falling from 90% to 10% 220 ns
tPD Input to output propagation delay INx to OUTx 0.7 1 µs
tDEAD Output dead time 200 ns
SHUNT CURRENT SENSE AND REGULATION (ISEN, VREF)
AV ISEN gain VREF = 2.5 V 9.6 10 10.4 V/V
tOFF Current regulation off time 25 µs
tBLANK Current regulation blanking time 2 µs
PROTECTION CIRCUITS
VUVLO Supply undervoltage lockout (UVLO) Supply rising 4.15 4.3 4.45 V
Supply falling 4.05 4.2 4.35 V
VUVLO_HYS Supply UVLO hysteresis Rising to falling threshold 100 mV
tUVLO Supply undervoltage deglitch time 10 µs
IOCP Overcurrent protection trip point 4.5 ≤ VVM < 5.5 V 3.7 A
VVM ≥ 5.5 V 4.1 A
VOCP_ISEN Overcurrent protection trip point on ISEN pin 0.7 V
tOCP Overcurrent protection deglitch time 1.5 µs
TTSD Thermal shutdown temperature 150 175 °C
THYS Thermal shutdown hysteresis 40 °C
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |