ZHCSP68C December   2021  – October 2022 DRV8328

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Device Comparison Table
  6. Pin Configuration and Functions
  7. Specification
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings Comm
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information 1pkg
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Three BLDC Gate Drivers
        1. 8.3.1.1 PWM Control Modes
          1. 8.3.1.1.1 6x PWM Mode
          2. 8.3.1.1.2 3x PWM Mode
        2. 8.3.1.2 Device Hardware Interface
        3. 8.3.1.3 Gate Drive Architecture
          1. 8.3.1.3.1 Propagation Delay
          2. 8.3.1.3.2 Deadtime and Cross-Conduction Prevention
      2. 8.3.2 AVDD Linear Voltage Regulator
      3. 8.3.3 Pin Diagrams
      4. 8.3.4 Gate Driver Shutdown Sequence (DRVOFF)
      5. 8.3.5 Gate Driver Protective Circuits
        1. 8.3.5.1 PVDD Supply Undervoltage Lockout (PVDD_UV)
        2. 8.3.5.2 AVDD Power on Reset (AVDD_POR)
        3. 8.3.5.3 GVDD Undervoltage Lockout (GVDD_UV)
        4. 8.3.5.4 BST Undervoltage Lockout (BST_UV)
        5. 8.3.5.5 MOSFET VDS Overcurrent Protection (VDS_OCP)
        6. 8.3.5.6 VSENSE Overcurrent Protection (SEN_OCP)
        7. 8.3.5.7 Thermal Shutdown (OTSD)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Gate Driver Functional Modes
        1. 8.4.1.1 Sleep Mode
        2. 8.4.1.2 Operating Mode
        3. 8.4.1.3 Fault Reset (nSLEEP Reset Pulse)
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Three Phase Brushless-DC Motor Control
        1. 9.2.1.1 Detailed Design Procedure
          1. 9.2.1.1.1 Motor Voltage
          2. 9.2.1.1.2 Bootstrap Capacitor and GVDD Capacitor Selection
          3. 9.2.1.1.3 Gate Drive Current
          4. 9.2.1.1.4 Gate Resistor Selection
          5. 9.2.1.1.5 System Considerations in High Power Designs
            1. 9.2.1.1.5.1 Capacitor Voltage Ratings
            2. 9.2.1.1.5.2 External Power Stage Components
            3. 9.2.1.1.5.3 Parallel MOSFET Configuration
          6. 9.2.1.1.6 Dead Time Resistor Selection
          7. 9.2.1.1.7 VDSLVL Selection
          8. 9.2.1.1.8 AVDD Power Losses
          9. 9.2.1.1.9 Power Dissipation and Junction Temperature Losses
      2. 9.2.2 Application Curves
  10. 10Power Supply Recommendations
    1. 10.1 Bulk Capacitance Sizing
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
    3. 11.3 Thermal Considerations
      1. 11.3.1 Power Dissipation
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Device Nomenclature
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 Related Links
    4. 12.4 Receiving Notification of Documentation Updates
    5. 12.5 Community Resources
    6. 12.6 Trademarks
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息
Dead Time Resistor Selection

Dead time insertion is available in the DRV8328 via a resistor (RDT) from the DT pin to ground as shown in Figure 9-6. The ranges of dead time in the DRV8328 is 100 ns to 2000 ns when RDT is tied to GND from the DT pin. A linear interpolation of the resistance value is used to set the appropriate dead time.

Figure 9-6 Dead time resistor

Dead time (in nanoseconds) can be calculated from the dead time resistor calculation in Equation 1.

Dead time can also be implemented from the PWM inputs generated by an MCU. If dead time is inserted at the PWM inputs and the DRV8328, then the driver output PWM dead time is the larger of the two dead times. For instance, if 200 ns dead time is inserted at the MCU inputs and 50 ns dead time is inserted in the DRV8328 via the DT pin, then the output driver PWM dead time will be 200 ns.