ZHCSG57B March 2017 – December 2018 DRV8702D-Q1 , DRV8703D-Q1
PRODUCTION DATA.
PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | |
---|---|---|---|---|---|---|
POWER SUPPLIES (VM, AVDD, DVDD) | ||||||
t(SLEEP) | Sleep time | nSLEEP = low to sleep mode | 100 | µs | ||
t(wu) | Wake-up time | nSLEEP = high to output change | 1 | ms | ||
ton | Turn on time | VM > UVLO2 to output transition | 1 | ms | ||
CHARGE PUMP (VCP, CPH, CPL) | ||||||
fS(VCP) | Charge-pump switching frequency | VM > UVLO2 | 200 | 400 | 700 | kHz |
CONTROL INPUTS (IN1, IN2, nSLEEP, MODE, nSCS, SCLK, SDI, PH, EN) | ||||||
tpd | Propagation delay | removed PH and EN pinsIN1, IN2 to GH or GL | 500 | ns | ||
FET GATE DRIVERS (GH1, GH2, SH1, SH2, GL1, GL2) | ||||||
t(DEAD) | Output dead time (DRV8702D-Q1) | Observed t(DEAD) depends on IDRIVE setting | 240 | ns | ||
t(DEAD) | Output dead time (DRV8703D-Q1) | TDEAD = 2’b00; Observed t(DEAD) depends on IDRIVE setting | 120 | ns | ||
TDEAD = 2’b01; Observed t(DEAD) depends on IDRIVE setting | 240 | |||||
TDEAD = 2’b10; Observed t(DEAD) depends on IDRIVE setting | 480 | |||||
TDEAD = 2’b11; Observed t(DEAD) depends on IDRIVE setting | 960 | |||||
t(DRIVE) | Gate drive time | 2.5 | µs | |||
CURRENT SHUNT AMPLIFIER AND PWM CURRENT CONTROL (SP, SN, SO, VREF) | ||||||
tS | Settling time to ±1%(1) | VSP = VSN = GND to VSP = 240 mV, VSN = GND, AV= 10; C(SO) = 200 pF | 0.5 | µs | ||
VSP = VSN = GND to VSP = 120 mV, VSN = GND, AV= 20; C(SO) = 200 pF | 1 | |||||
VSP = VSN = GND to VSP = 60 mV, VSN = GND, AV= 40; C(SO) = 200 pF | 2 | |||||
VSP = VSN = GND to VSP = 30 mV, VSN = GND, AV= 80; C(SO) = 200 pF | 4 | |||||
toff | PWM off-time (DRV8702D-Q1) | 25 | µs | |||
toff | PWM off-time (DRV8703D-Q1) | TOFF = 00 | 25 | µs | ||
TOFF = 01 | 50 | |||||
TOFF = 10 | 100 | |||||
TOFF = 11 | 200 | |||||
t(BLANK) | PWM blanking time | 2 | µs | |||
PROTECTION CIRCUITS | ||||||
t(UVLO) | VM UVLO falling deglitch time | VM falling; UVLO report | 10 | µs | ||
t(OCP) | Overcurrent deglitch time | 3.7 | 4 | 4.3 | µs | |
t(RETRY) | Overcurrent retry time | 2.8 | 3 | 3.2 | ms | |
t(WD) | Watchdog time out (DRV8703D-Q1) | WD_DLY = 2’b00 | 10 | ms | ||
WD_DLY = 2’b01 | 20 | |||||
WD_DLY = 2’b10 | 50 | |||||
WD_DLY = 2’b11 | 100 | |||||
t(RESET) | Watchdog timer reset period | 64 | µs | |||
SPI | ||||||
t(SPI_READY) | SPI read after power on | VM > VUVLO1 | 5 | 10 | ms | |
td(SDO) | SDO output data delay time, CLK high to SDO valid | CL = 20 pF | 30 | ns | ||
ta | SCS access time, SCS low to SDO out of high impedance | 10 | ns | |||
tdis | SCS disable time, SCS high to SDO high impedance | 10 | ns |