米6体育平台手机版

ZHCSJ96B September 2005 – January 2019 DS90LT012AH

PRODUCTION DATA.

封装选项

机械数据 (封装 | 引脚)

DBV|5
- MPDS018T

散热焊盘机械数据 (封装 | 引脚)

订购信息

6.5 Electrical Characteristics

Over Supply Voltage and Operating Temperature ranges, unless otherwise specified. ⁽¹⁾⁽²⁾

PARAMETER		TEST CONDITIONS		PIN	MIN	TYP	MAX	UNIT
V_TH	Differential Input High Threshold	V_CM dependant on V_DD⁽³⁾		IN+, IN−		−30	0	mV
V_TL	Differential Input Low Threshold	V_CM dependant on V_DD⁽³⁾			−100	−30		mV
V_CM	Common-Mode Voltage	V_DD = 2.7 V, V_ID = 100 mV			0.05		2.35	V
		V_DD = 3 V to 3.6 V, V_ID = 100 mV			0.05		V_DD – 0.3	V
		T_A = 125°C			0.1		2.35	V
I_IN	Input Current (DS90LV012A)	V_IN = +2.8 V	V_DD = 3.6 V or 0 V		−10	±1	+10	μA
		V_IN = 0 V	V_DD = 3.6 V or 0 V		−10	±1	+10	μA
		V_IN = +3.6 V	V_DD = 0 V		−20		+20	μA
ΔI_IN	Change in Magnitude of I_IN	V_IN = +2.8 V	V_DD = 3.6 V or 0 V			4		μA
		V_IN = 0 V	V_DD = 3.6 V or 0 V			4		μA
		V_IN = +3.6 V	V_DD = 0 V			4		μA
I_IND	Differential Input Current	V_IN+ = +0.4 V, V_IN− = +0 V			3	3.9	4.4	mA
I_IND	Differential Input Current	V_IN+ = +2.4 V, V_IN− = +2.0 V			3	3.9	4.4	mA
R_T	Integrated Termination Resistor					100		Ω
C_IN	Input Capacitance	IN+ = IN− = GND				3		pF
V_OH	Output High Voltage	I_OH = −0.4 mA, V_ID = +200 mV		TTL OUT	2.4	3.1		V
		I_OH = −0.4 mA, Inputs terminated			2.4	3.1		V
		I_OH = −0.4 mA, Inputs shorted			2.4	3.1		V
V_OL	Output Low Voltage	I_OL = 2 mA, V_ID = −200 mV				0.3	0.5	V
I_OS	Output Short-Circuit Current	V_OUT = 0V ⁽⁴⁾			−15	−50	−100	mA
V_CL	Input Clamp Voltage	I_CL = −18 mA			−1.5	−0.7		V
I_DD	No Load Supply Current	Inputs Open		V_DD		5.4	9	mA

(1) Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground unless otherwise specified (such as V_ID).

(2) All typicals are given for: V_DD = +3.3 V and T_A = +25°C.

(3) V_DD is always higher than IN+ and IN− voltage. IN+ and IN− are allowed to have voltage range −0.05 V to +2.35 V when V_DD = 2.7 V and |V_ID| / 2 to V_DD − 0.3 V when V_DD = 3.0 V to 3.6 V. V_ID is not allowed to be greater than 100 mV when V_CM = 0.05 V to 2.35 V when V_DD = 2.7 V or when V_CM = |V_ID| / 2 to V_DD − 0.3 V when V_DD = 3.0 V to 3.6 V.

(4) Output short-circuit current (I_OS) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not exceed maximum junction temperature specification.