4 Revision History
Changes from Revision A (April 2007) to Revision B (May 2023)
- 更新了整个文档中的表格、图和交叉参考的编号格式Go
- 添加了封装信息 表、引脚配置和功能 部分、规格 部分、详细描述 部分、应用和实施 部分、器件和文档支持 部分以及机械、封装和可订购信息 部分Go
- 向特性 中添加了输入电压噪声、高带宽和温度范围要点Go
- 更改了特性 要点以显示正确的封装名称Go
- 更改了应用 要点以显示更新后的链接Go
- 将“封装信息”表的列名称从“封装尺寸（标称值）”更改为“封装尺寸”并添加了有关封装尺寸的注释Go
- Added single supply specification to Absolute Maximum Ratings
Go
- Added note clarifying output short-circuit to ground in Absolute Maximum Ratings refers to short-circuit to VS / 2Go
- Added single supply specification to Recommended Operating Conditions
Go
- Changed input common-mode voltage range specification from V – 2 to (V–) + 2 in Recommended Operating Conditions
Go
- Deleted INA128-HT and INA129-HT operating temperature specifications from Recommended Operating Conditions
Go
- Added specified temperature range to Recommended Operating Conditions
Go
- Added test conditions below Electrical Characterstics titleGo
- Changed test condition for offset voltage drift specification in Electrical Characteristics from "TA = TMIN to TMAX" to " TA = –40℃ to +85℃" for clarityGo
- Changed "±0.5±0/G" to "±0.5±20/G" in MAX column of Offset voltage RTI vs temperature row of Electrical Characteristics.Go
- Changed typical long-term stability specification from ±0.1±3/GµV/mo to ±0.2±3/GµV/mo in Electrical Characteristics
Go
- Deleted typical specification and changed common-mode voltage specification from (V–) + 2 V minimum and (V+) – 2 V maximum across one row in Electrical CharacteristicsGo
- Deleted typical VCM specifications in Electrical Characteristics
Go
- Added test condition of "RS = 0 Ω" to safe input voltage specification in Electrical Characteristics for clarityGo
- Changed parameter name to Input bias current and added test condition "TA = –40°C to +85°C" to input bias current drift specification in Electrical Characteristics for clarityGo
- Changed parameter name to Input offset current drift and added test condition "TA = –40°C to +85°C" to input offset current drift specification in Electrical Characteristics for clarityGo
- Changed maximum gain error specification for INA128PA/UA and INA129PA/UA with G = 1 from ±0.01% to ±0.1% in Electrical Characteristics
Go
- Changed parameter name to Gain drift and added test condition "TA = –40°C to +85°C" for gain drift in Electrical Characteristics for clarityGo
- Changed parameter names from "Voltage - Positive" to "Positive output voltage swing" and from "Voltage - Negative" to "Negative output voltage swing" in Electrical Characteristics
Go
- Deleted typical positive and negative output voltage swing specifications in Electrical Characteristics
Go
- Added test condition "Continuous to VS / 2" short-circuit current specification in Electrical Characteristics for clarityGo
- Changed typical bandwidth specification for G = 10 from 700 kHz to 600 kHz in Electrical Characteristics
Go
- Changed typical slew rate specification from 4 V/µs to 1.2 V/µs in Electrical Characteristics
Go
- Changed typical settling time specification for G = 1, G = 10, from 7 µs to 9 µs in Electrical Characteristics
Go
- Deleted parameter "Temperature Range" as made redundant by "Recommended Operating Conditions" and "Absolute Maximum Ratings"
Go
- Changed parameter name to "Total quiescent current" and deleted redundant voltage range, operating temperature range, and specification temperature range specifications from Electrical Characteristics
Go
- Added test conditions below the Typical Characteristics
titleGo
- Changed Figure 6-1, Gain vs Frequency
Go
- Changed Figure 6-3, Positive Power Supply Rejection vs
Frequency
Go
- Changed Figure 6-4, Negative Power Supply Rejection vs
Frequency
Go
- Changed Figure 6-7, Crosstalk vs Frequency
Go
- Changed Figure 6-8, Input-Referred Voltage Noise vs
Frequency
Go
- Changed Figure 6-9, Settling Time vs Gain
Go
- Changed Figure 6-11, Input Overvoltage V/I
Characteristics
Go
- Changed Figure 6-12, Offset Voltage Warm-Up
Go
- Changed Output Voltage Swing vs Output Current, into two
separate plots, one for positive (Figure 6-14) and one for negative (Figure
6-15)Go
- Changed Figure 6-22 to Figure 6-24, Large-Signal Step
Response
Go