米6体育平台手机版

SLLSFS9C September 2023 – October 2024 ISOM8110 , ISOM8111 , ISOM8112 , ISOM8113 , ISOM8115 , ISOM8116 , ISOM8117 , ISOM8118

PRODUCTION DATA

封装选项

机械数据 (封装 | 引脚)

DFG|4
- MPSS148B

散热焊盘机械数据 (封装 | 引脚)

订购信息

6.4 Insulation Specifications

PARAMETER		TEST CONDITIONS	VALUE	UNIT
PARAMETER		TEST CONDITIONS	4-DFG, 4-DFH	UNIT
IEC 60664-1
CLR	External clearance⁽¹⁾	Side 1 to side 2 distance through air	> 5	mm
CPG	External creepage⁽¹⁾	Side 1 to side 2 distance across package surface	> 5	mm
DTI	Distance through the insulation	Minimum internal gap (internal clearance)	>17	µm
CTI	Comparative tracking index	IEC 60112; UL 746A	>400	V
	Material Group	According to IEC 60664-1	II
	Overvoltage category per IEC 60664-1	Rated mains voltage ≤ 150 V_RMS	I-IV
		Rated mains voltage ≤ 300 V_RMS	I-IV
		Rated mains voltage ≤ 600 V_RMS	I-III
DIN VDE V 0884-11:2017 ⁽⁶⁾
V_IORM	Maximum repetitive peak isolation voltage	AC voltage (bipolar)	707	V_PK
V_IOWM	Maximum isolation working voltage	AC voltage (sine wave); time-dependent dielectric breakdown (TDDB) test	500	V_RMS
V_IOWM	Maximum isolation working voltage	DC voltage	707	V_DC
V_IOTM	Maximum transient isolation voltage	V_TEST = V_IOTM, t = 60s (qualification); V_TEST = 1.2 × V_IOTM, t = 1s (100% production)	5303	V_PK
V_IMP	Maximum impulse voltage ⁽²⁾	Tested in air, 1.2/50µs waveform per IEC 62368-1	7200	V_PK
V_IOSM	Maximum surge isolation voltage⁽³⁾	V_ISOM ≥ 1.3 x V_IMP; tested in oil (qualification test), 1.2/50µs waveform per IEC 62368-1	10000	V_PK
q_pd	Apparent charge⁽⁴⁾	Method a: After I/O safety test subgroup 2/3, V_ini = V_IOTM, t_ini = 60s; V_pd(m) = 1.2 × V_IORM , t_m = 10s	≤ 5	pC
		Method a: After environmental tests subgroup 1, V_ini = V_IOTM, t_ini = 60s; V_pd(m) = 1.6 × V_IORM , t_m = 10s	≤ 5
		Method b: At routine test (100% production) and preconditioning (type test), V_ini = 1.2 × V_IOTM, t_ini = 1s; V_pd(m) = 1.875 × V_IORM , t_m = 1s	≤ 5
C_IO	Barrier capacitance, input to output⁽⁵⁾	V_IO = 0.4 × sin (2 πft), f = 1MHz	1	pF
R_IO	Insulation resistance, input to output⁽⁵⁾	V_IO = 500V, T_A = 25°C	> 10¹²	Ω
		V_IO = 500V, 100°C ≤ T_A ≤ 125°C	> 10¹¹
		V_IO = 500V at T_S = 150°C	> 10⁹
	Pollution degree		2
	Climatic category		40/125/21
UL 1577
V_ISO	Withstand isolation voltage	V_TEST = V_ISO, t = 60s (qualification); V_TEST = 1.2 × V_ISO , t = 1s (100% production)	3750	V_RMS

(1) Creepage and clearance requirements should be applied according to the specific equipment isolation standards of an application. Care should be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in certain cases. Techniques such as inserting grooves, ribs, or both on a printed circuit board are used to help increase these specifications.

(2) Testing is carried out in air to determine the surge immunity of the package.

(3) Testing is carried out in oil to determine the intrinsic surge immunity of the isolation barrier.

(4) Apparent charge is electrical discharge caused by a partial discharge (pd).

(5) All pins on each side of the barrier tied together creating a two-pin device.

(6) This coupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits.