ZHCSQH3 November   2022 LMG3522R030

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  7. 7 Parameter Measurement Information
    1. 7.1 Switching Parameters
      1. 7.1.1 Turn-On Times
      2. 7.1.2 Turn-Off Times
      3. 7.1.3 Drain-Source Turn-On Slew Rate
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  GaN FET Operation Definitions
      2. 8.3.2  Direct-Drive GaN Architecture
      3. 8.3.3  Drain-Source Voltage Capability
      4. 8.3.4  Internal Buck-Boost DC-DC Converter
      5. 8.3.5  VDD Bias Supply
      6. 8.3.6  Auxiliary LDO
      7. 8.3.7  Fault Detection
        1. 8.3.7.1 Overcurrent Protection and Short-Circuit Protection
        2. 8.3.7.2 Overtemperature Shutdown
        3. 8.3.7.3 UVLO Protection
        4. 8.3.7.4 Fault Reporting
      8. 8.3.8  Drive Strength Adjustment
      9. 8.3.9  Temperature-Sensing Output
      10. 8.3.10 Ideal-Diode Mode Operation
        1. 8.3.10.1 Overtemperature-Shutdown Ideal-Diode Mode
    4. 8.4 Start Up Sequence
    5. 8.5 Safe Operation Area (SOA)
      1. 8.5.1 Safe Operation Area (SOA) - Repetitive SOA
    6. 8.6 Device Functional Modes
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Slew Rate Selection
          1. 9.2.2.1.1 Start-Up and Slew Rate With Bootstrap High-Side Supply
        2. 9.2.2.2 Signal Level-Shifting
        3. 9.2.2.3 Buck-Boost Converter Design
      3. 9.2.3 Application Curves
    3. 9.3 Do's and Don'ts
    4. 9.4 Power Supply Recommendations
      1. 9.4.1 Using an Isolated Power Supply
      2. 9.4.2 Using a Bootstrap Diode
        1. 9.4.2.1 Diode Selection
        2. 9.4.2.2 Managing the Bootstrap Voltage
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
        1. 9.5.1.1 Solder-Joint Reliability
        2. 9.5.1.2 Power-Loop Inductance
        3. 9.5.1.3 Signal-Ground Connection
        4. 9.5.1.4 Bypass Capacitors
        5. 9.5.1.5 Switch-Node Capacitance
        6. 9.5.1.6 Signal Integrity
        7. 9.5.1.7 High-Voltage Spacing
        8. 9.5.1.8 Thermal Recommendations
      2. 9.5.2 Layout Examples
  10. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 接收文档更新通知
    3. 10.3 支持资源
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Export Control Notice
    7. 10.7 术语表
  11. 11Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.6 Switching Characteristics

Unless otherwise noted: voltage, resistance, capacitance, and inductance are respect to SOURCE connected with reference ground; –40 ℃ ≤ TJ ≤ 125 ℃; 9 V ≤ VVDD ≤ 18 V; VIN = 0 V; RDRV connected to LDO5V;  LBBSW = 4.7 µH
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SWITCHING TIMES
td(on)(Idrain) Drain-current turn-on delay time From VIN > VIN,IT+ to ID > 1 A, VBUS = 400 V, LHB current = 10 A, see Figure 7-1 and Figure 7-2        28 42 ns
td(on) Turn-on delay time  From VIN > VIN,IT+ to VDS < 320 V, VBUS = 400 V, LHB current = 10 A, see Figure 7-1 and Figure 7-2    33 54 ns
tr(on) Turn-on rise time From VDS < 320 V to VDS < 80 V, VBUS = 400 V, LHB current = 10 A, see Figure 7-1 and Figure 7-2        2.8 4.3 ns
td(off) Turn-off delay time  From VIN < VIN,IT– to VDS > 80 V, VBUS = 400 V, LHB current = 10 A, see Figure 7-1 and Figure 7-2      48 69 ns
tf(off) Turn-off fall time(1) From VDS > 80 V to VDS > 320 V, VBUS = 400 V, LHB current = 10 A, see Figure 7-1 and Figure 7-2        22 ns
Minimum IN high pulse-width for FET turn-on VIN rise/fall times < 1 ns, VDS falls to < 200 V, VBUS = 400 V, LHB current = 10 A, see Figure 7-1   24 ns
STARTUP TIMES
t(start) Driver start-up time From VVDD > VVDD,T+(UVLO) to FAULT high, CLDO5V = 100 nF, CVNEG = 2.2 µF at 0-V bias linearly decreasing to 1.5 µF at 15-V bias 310 470 us
FAULT TIMES
toff(OC) Overcurrent fault FET turn-off time, FET on before overcurrent VIN = 5 V, From ID > IT(OC) to ID < 50 A, ID di/dt = 100 A/µs 115 170 ns
toff(SC) Short-circuit current fault FET turn-off time, FET on before short circuit VIN = 5 V, From ID > IT(SC) to ID < 50 A, ID di/dt = 700 A/µs 65 100 ns
Overcurrent fault FET turn-off time, FET turning on into overcurrent From ID > IT(OC) to ID < 50 A 200 250 ns
Short-circuit fault FET turn-off time, FET turning on into short circuit From ID > IT(SC) to ID < 50 A 80 180 ns
IN reset time to clear FAULT latch From VIN < VIN,IT– to FAULT high 250 380 580 us
t(window)(OC) Overcurrent fault to short-circuit fault window time 50 ns
IDEAL-DIODE MODE CONTROL TIMES
Ideal-diode mode FET turn-on time VDS < VT(3rd) to FET turn-on, VDS being discharged by half-bridge configuration inductor at 5 A 50 65 ns
Ideal-diode mode FET turn-off time ID > IT(ZC) to FET turn-off, ID di/dt = 100 A/µs created with a half-bridge configuration 55 76 ns
Overtemperature-shutdown ideal-diode mode IN falling blanking time  150 230 360 ns
(1) During turn-off, VDS rise time is the result of the resonance of COSS and loop inductance as well as load current.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |