ZHCSMJ6B November   2020  – March 2021 LMK5C33216

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Device Comparison
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Diagrams
  8. 8 Parameter Measurement Information
    1. 8.1 Differential Voltage Measurement Terminology
    2. 8.2 Output Clock Test Configurations
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
      1. 9.2.1 PLL Architecture Overview
      2. 9.2.2 DPLL
        1. 9.2.2.1 Independent DPLL Operation
        2. 9.2.2.2 Cascaded DPLL Operation
        3. 9.2.2.3 APLL Cascaded with DPLL
      3. 9.2.3 APLL-Only Mode
    3. 9.3 Feature Description
      1. 9.3.1  Oscillator Input (XO)
      2. 9.3.2  Reference Inputs
      3. 9.3.3  Clock Input Interfacing and Termination
      4. 9.3.4  Reference Input Mux Selection
        1. 9.3.4.1 Automatic Input Selection
        2. 9.3.4.2 Manual Input Selection
      5. 9.3.5  Hitless Switching
        1. 9.3.5.1 Hitless Switching with Phase Cancellation
        2. 9.3.5.2 Hitless Switching With Phase Slew Control
        3. 9.3.5.3 Hitless Switching With 1-PPS Inputs
      6. 9.3.6  Gapped Clock Support on Reference Inputs
      7. 9.3.7  Input Clock and PLL Monitoring, Status, and Interrupts
        1. 9.3.7.1 XO Input Monitoring
        2. 9.3.7.2 Reference Input Monitoring
          1. 9.3.7.2.1 Reference Validation Timer
          2. 9.3.7.2.2 Frequency Monitoring
          3. 9.3.7.2.3 Missing Pulse Monitor (Late Detect)
          4. 9.3.7.2.4 Runt Pulse Monitor (Early Detect)
          5. 9.3.7.2.5 Phase Valid Monitor for 1-PPS Inputs
        3. 9.3.7.3 PLL Lock Detectors
        4. 9.3.7.4 Tuning Word History
        5. 9.3.7.5 Status Outputs
        6. 9.3.7.6 Interrupt
      8. 9.3.8  PLL Relationships
        1. 9.3.8.1  PLL Frequency Relationships
          1. 9.3.8.1.1 APLL Phase Detector Frequency
          2. 9.3.8.1.2 APLL VCO Frequency
          3. 9.3.8.1.3 DPLL TDC Frequency
          4. 9.3.8.1.4 DPLL VCO Frequency
          5. 9.3.8.1.5 Clock Output Frequency
        2. 9.3.8.2  Analog PLLs (APLL1, APLL2, APLL3)
        3. 9.3.8.3  APLL Reference Paths
          1. 9.3.8.3.1 APLL XO Doubler
          2. 9.3.8.3.2 APLL XO Reference (R) Divider
        4. 9.3.8.4  APLL Phase Frequency Detector (PFD) and Charge Pump
        5. 9.3.8.5  APLL Feedback Divider Paths
          1. 9.3.8.5.1 APLL N Divider with SDM
        6. 9.3.8.6  APLL Loop Filters (LF1, LF2, LF3)
        7. 9.3.8.7  APLL Voltage Controlled Oscillators (VCO1, VCO2, VCO3)
          1. 9.3.8.7.1 VCO Calibration
        8. 9.3.8.8  APLL VCO Clock Distribution Paths
        9. 9.3.8.9  DPLL Reference (R) Divider Paths
        10. 9.3.8.10 DPLL Time-to-Digital Converter (TDC)
        11. 9.3.8.11 DPLL Loop Filter (DLF)
        12. 9.3.8.12 DPLL Feedback (FB) Divider Path
      9. 9.3.9  Output Clock Distribution
      10. 9.3.10 Output Channel Muxes
      11. 9.3.11 Output Dividers (OD)
      12. 9.3.12 SYSREF
      13. 9.3.13 Output Delay
      14. 9.3.14 Clock Outputs (OUTx_P/N)
        1. 9.3.14.1 Differential Output
        2. 9.3.14.2 LVCMOS Output
        3. 9.3.14.3 Output Auto-Mute During LOL
      15. 9.3.15 Glitchless Output Clock Start-Up
      16. 9.3.16 Clock Output Interfacing and Termination
      17. 9.3.17 Output Synchronization (SYNC)
      18. 9.3.18 Zero-Delay Mode (ZDM) Synchronization
      19. 9.3.19 Time of Day (ToD) Counter
        1. 9.3.19.1 Configuring ToD Functionality
        2. 9.3.19.2 SPI as a Trigger Source
        3. 9.3.19.3 GPIO Pin as a ToD Trigger Source
          1. 9.3.19.3.1 An Example: Making a time measurement using ToD and GPIO1 as trigger
        4. 9.3.19.4 ToD Timing
        5. 9.3.19.5 Other ToD Behavior
    4. 9.4 Device Functional Modes
      1. 9.4.1 Device Start-Up
        1. 9.4.1.1 ROM Selection
        2. 9.4.1.2 EEPROM Overlay
      2. 9.4.2 DPLL Operating States
        1. 9.4.2.1 Free-Run
        2. 9.4.2.2 Lock Acquisition
        3. 9.4.2.3 DPLL Locked
        4. 9.4.2.4 Holdover
      3. 9.4.3 PLL Start-Up Sequence
      4. 9.4.4 Digitally-Controlled Oscillator (DCO) Frequency and Phase Adjustment
        1. 9.4.4.1 DPLL DCO Control
          1. 9.4.4.1.1 DPLL DCO Relative Adjustment Frequency Step Size
          2. 9.4.4.1.2 APLL DCO Frequency Step Size
      5. 9.4.5 APLL Frequency Control
      6. 9.4.6 Zero-Delay Mode Synchronization
    5. 9.5 Programming
      1. 9.5.1 Interface and Control
      2. 9.5.2 I2C Serial Interface
        1. 9.5.2.1 I2C Block Register Transfers
      3. 9.5.3 SPI Serial Interface
        1. 9.5.3.1 SPI Block Register Transfer
      4. 9.5.4 Register Map Generation
      5. 9.5.5 General Register Programming Sequence
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Device Start-Up Sequence
      2. 10.1.2 Power Down (PD#) Pin
      3. 10.1.3 Strap Pins for Start-Up
      4. 10.1.4 ROM and EEPROM
      5. 10.1.5 Power Rail Sequencing, Power Supply Ramp Rate, and Mixing Supply Domains
        1. 10.1.5.1 Power-On Reset (POR) Circuit
        2. 10.1.5.2 Powering Up From a Single-Supply Rail
        3. 10.1.5.3 Power Up From Split-Supply Rails
        4. 10.1.5.4 Non-Monotonic or Slow Power-Up Supply Ramp
      6. 10.1.6 Slow or Delayed XO Start-Up
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
    3. 10.3 Do's and Don'ts
  11. 11Power Supply Recommendations
    1. 11.1 Power Supply Bypassing
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
    3. 12.3 Thermal Reliability
      1. 12.3.1 Support for PCB Temperature up to 105°C
  13. 13Device and Documentation Support
    1. 13.1 Documentation Support
      1. 13.1.1 Related Documentation
    2. 13.2 接收文档更新通知
    3. 13.3 支持资源
    4. 13.4 Trademarks
    5. 13.5 术语表
    6. 13.6 静电放电警告
  14. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息
9.3.19.3.1 An Example: Making a time measurement using ToD and GPIO1 as trigger
  1. Configure ToD registers as desired. In this example:
    • REF0_MISSCLK_VCOSEL is 0 so that VCO3 frequency / 8 is used for ToD clock rate
    • TOD_CNTR_TRIG = 1 for GPIO1 trigger
    • TOD_CNTR_CLR = 0 for normal operation

  2. Set GPIO1_MODE = 0x27 (TOD_TRIG_SEL) and GPIO1_POL as desired, 0 in this example for active high input.

  3. Provide rising edge on GPIO1 to capture current ToD counter value into the TOD_CNTR field.
  4. Read and store the TOD_CNTR field for the first time.
    • Example: 1st_captured_TOD_value = 204 354.
  5. Provide rising edge on GPIO1.
  6. Read and store the TOD_CNTR field for the second time.
    • Example: 2nd_captured_TOD_value = 76 516 568
  7. Calculate time delta using equation #1 with ToD clock rate of 307.2 MHz.
    • 248.412 155 ms = (76 516 568 - 204 354) / 307.2 MHz
    • Because the ToD clock rate is 307.2 MHz, the accuracy of the measurement is +/- 3.26 ns.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |