ZHCSNP1A March   2021  – October 2021 MCT8316Z

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 SPI Timing Requirements
    7. 7.7 SPI Secondary Mode Timings
    8. 7.8 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Output Stage
      2. 8.3.2  PWM Control Mode (1x PWM Mode)
        1. 8.3.2.1 Analog Hall Input Configuration
        2. 8.3.2.2 Digital Hall Input Configuration
        3. 8.3.2.3 Asynchronous Modulation
        4. 8.3.2.4 Synchronous Modulation
        5. 8.3.2.5 Motor Operation
      3. 8.3.3  Device Interface Modes
        1. 8.3.3.1 Serial Peripheral Interface (SPI)
        2. 8.3.3.2 Hardware Interface
      4. 8.3.4  Step-Down Mixed-Mode Buck Regulator
        1. 8.3.4.1 Buck in Inductor Mode
        2. 8.3.4.2 Buck in Resistor mode
        3. 8.3.4.3 Buck Regulator with External LDO
        4. 8.3.4.4 AVDD Power Sequencing on Buck Regulator
        5. 8.3.4.5 Mixed mode Buck Operation and Control
      5. 8.3.5  AVDD Linear Voltage Regulator
      6. 8.3.6  Charge Pump
      7. 8.3.7  Slew Rate Control
      8. 8.3.8  Cross Conduction (Dead Time)
      9. 8.3.9  Propagation Delay
        1. 8.3.9.1 Driver Delay Compensation
      10. 8.3.10 Pin Diagrams
        1. 8.3.10.1 Logic Level Input Pin (Internal Pulldown)
        2. 8.3.10.2 Logic Level Input Pin (Internal Pullup)
        3. 8.3.10.3 Open Drain Pin
        4. 8.3.10.4 Push Pull Pin
        5. 8.3.10.5 Four Level Input Pin
        6. 8.3.10.6 Seven Level Input Pin
      11. 8.3.11 Active Demagnetization
        1. 8.3.11.1 Automatic Synchronous Rectification Mode (ASR Mode)
          1. 8.3.11.1.1 Automatic Synchronous Rectification in Commutation
          2. 8.3.11.1.2 Automatic Synchronous Rectification in PWM Mode
        2. 8.3.11.2 Automatic Asynchronous Rectification Mode (AAR Mode)
      12. 8.3.12 Cycle-by-Cycle Current Limit
        1. 8.3.12.1 Cycle by Cycle Current Limit with 100% Duty Cycle Input
      13. 8.3.13 Hall Comparators (Analog Hall Inputs)
      14. 8.3.14 Advance Angle
      15. 8.3.15 FGOUT Signal
      16. 8.3.16 Protections
        1. 8.3.16.1  VM Supply Undervoltage Lockout (NPOR)
        2. 8.3.16.2  AVDD Undervoltage Lockout (AVDD_UV)
        3. 8.3.16.3  BUCK Undervoltage Lockout (BUCK_UV)
        4. 8.3.16.4  VCP Charge Pump Undervoltage Lockout (CPUV)
        5. 8.3.16.5  Overvoltage Protections (OV)
        6. 8.3.16.6  Overcurrent Protection (OCP)
          1. 8.3.16.6.1 OCP Latched Shutdown (OCP_MODE = 00b)
          2. 8.3.16.6.2 OCP Automatic Retry (OCP_MODE = 01b)
          3. 8.3.16.6.3 OCP Report Only (OCP_MODE = 10b)
          4. 8.3.16.6.4 OCP Disabled (OCP_MODE = 11b)
        7. 8.3.16.7  Buck Overcurrent Protection
        8. 8.3.16.8  Motor Lock (MTR_LOCK)
          1. 8.3.16.8.1 MTR_LOCK Latched Shutdown (MTR_LOCK_MODE = 00b)
          2. 8.3.16.8.2 MTR_LOCK Automatic Retry (MTR_LOCK_MODE = 01b)
          3. 8.3.16.8.3 MTR_LOCK Report Only (MTR_LOCK_MODE= 10b)
          4. 8.3.16.8.4 MTR_LOCK Disabled (MTR_LOCK_MODE = 11b)
          5. 8.3.16.8.5 77
        9. 8.3.16.9  Thermal Warning (OTW)
        10. 8.3.16.10 Thermal Shutdown (OTS)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Functional Modes
        1. 8.4.1.1 Sleep Mode
        2. 8.4.1.2 Operating Mode
        3. 8.4.1.3 Fault Reset (CLR_FLT or nSLEEP Reset Pulse)
      2. 8.4.2 DRVOFF functionality
    5. 8.5 SPI Communication
      1. 8.5.1 Programming
        1. 8.5.1.1 SPI Format
    6. 8.6 Register Map
      1. 8.6.1 STATUS Registers
      2. 8.6.2 CONTROL Registers
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Hall Sensor Configuration and Connection
      1. 9.2.1 Typical Configuration
      2. 9.2.2 Open Drain Configuration
      3. 9.2.3 Series Configuration
      4. 9.2.4 Parallel Configuration
    3. 9.3 Typical Applications
      1. 9.3.1 Three-Phase Brushless-DC Motor Control With Current Limit
        1. 9.3.1.1 Detailed Design Procedure
          1. 9.3.1.1.1 Motor Voltage
          2. 9.3.1.1.2 Using Active Demagnetization
          3. 9.3.1.1.3 Using Delay Compensation
          4. 9.3.1.1.4 Using the Buck Regulator
          5. 9.3.1.1.5 Power Dissipation and Junction Temperature Losses
        2. 9.3.1.2 Application Curves
  10. 10Power Supply Recommendations
    1. 10.1 Bulk Capacitance
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
    3. 11.3 Thermal Considerations
      1. 11.3.1 Power Dissipation
  12. 12Device and Documentation Support
    1. 12.1 支持资源
    2. 12.2 Trademarks
    3. 12.3 Electrostatic Discharge Caution
    4. 12.4 术语表

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.3.16 Protections

The MCT8316Z family of devices is protected against VM undervoltage, charge pump undervoltage, and overcurrent events. Table 8-8 summarizes various faults details.

Table 8-8 Fault Action and Response (SPI Devices)
FAULTCONDITIONCONFIGURATIONREPORTH-BRIDGELOGICRECOVERY
VM undervoltage
(NPOR)		VVM < VUVLO——Hi-ZDisabledAutomatic:
VVM > VUVLO_R
CLR_FLT, nSLEEP Reset Pulse (NPOR bit)
AVDD undervoltage
(NPOR)		VAVDD < VAVDD_UV——Hi-ZDisabledAutomatic:
VAVDD > VAVDD_UV_R
CLR_FLT, nSLEEP Reset Pulse (NPOR bit)
Buck undervoltage
(BUCK_UV)		VFB_BK < VBK_UV—nFAULTActiveActiveAutomatic:
VFB_BK > VBUCK_UV_R
CLR_FLT, nSLEEP Reset Pulse (BUCK_UV bit)
Charge pump undervoltage
(VCP_UV)		VCP < VCPUV—nFAULTHi-ZActiveAutomatic:
VVCP > VCPUV
CLR_FLT, nSLEEP Reset Pulse (VCP_UV bit)
OverVoltage Protection
(OVP)		VVM > VOVPOVP_EN = 0bNoneActiveActiveNo action (OVP Disabled)
OVP_EN = 1bFAULTHi-ZActiveAutomatic:
VVM < VOVP
CLR_FLT, nSLEEP Reset Pulse (OVP bit)
Overcurrent Protection
(OCP)		IPHASE > IOCPOCP_MODE = 00bnFAULTHi-ZActiveLatched:
CLR_FLT, nSLEEP Reset Pulse (OCP bits)
OCP_MODE = 01bnFAULTHi-ZActiveRetry:
tRETRY
OCP_MODE = 10bnFAULTActiveActiveAutomatic:
CLR_FLT, nSLEEP Reset Pulse (OCP bits)
OCP_MODE = 11bNoneActiveActiveNo action
Buck Overcurrent Protection
(BUCK_OCP)		IBK > IBK_OC—nFAULTActiveActiveRetry:
tRETRY
SPI Error
(SPI_FLT)		SCLK fault and ADDR faultSPI_FLT_REP = 0bnFAULTActiveActiveAutomatic:
CLR_FLT, nSLEEP Reset Pulse (SPI_FLT bit)
SPI_FLT_REP = 1bNoneActiveActiveNo action
OTP Error
(OTP_ERR)		OTP reading is erroneous—nFAULTHi-ZActiveLatched:
Power Cycle, nSLEEP Reset Pulse
Motor Lock
(MTR_LOCK)		No Hall Signals > tMTR_LOCK_TDETMTR_LOCK_MODE = 00bnFAULTHi-ZActiveLatched:
CLR_FLT, nSLEEP Pulse (MTR_LOCK bit)
MTR_LOCK_MODE = 01bnFAULTHi-ZActiveRetry:
tMTR_LOCK_RETRY
MTR_LOCK_MODE = 10bnFAULTActiveActiveAutomatic:
CLR_FLT, nSLEEP Reset Pulse (OCP bits)
MTR_LOCK_MODE = 11bNoneActiveActiveNo action
Thermal warning
(OTW)		TJ > TOTWOTW_REP = 0bNoneActiveActiveNo action
OTW_REP = 1bnFAULTActiveActiveAutomatic:
TJ < TOTW – THYS
CLR_FLT, nSLEEP Pulse (OTW bit)
Thermal shutdown
(OTSD)		TJ > TOTSD—nFAULTHi-ZActiveAutomatic:
TJ < TOTSD – THYS
CLR_FLT, nSLEEP Pulse (OTS bit)
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |