ZHCSIT2F September 2010 – September 2018 MSP430F5304 , MSP430F5308 , MSP430F5309 , MSP430F5310
PRODUCTION DATA.
- 1器件概述
- 2修订历史记录
- 3Device Comparison
- 4Terminal Configuration and Functions
-
5Specifications
- 5.1 Absolute Maximum Ratings
- 5.2 ESD Ratings
- 5.3 Recommended Operating Conditions
- 5.4 Active Mode Supply Current Into VCC Excluding External Current
- 5.5 Low-Power Mode Supply Currents (Into VCC) Excluding External Current
- 5.6 Thermal Resistance Characteristics
- 5.7 Schmitt-Trigger Inputs – General-Purpose I/O (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7) (P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3, RST/NMI)
- 5.8 Inputs – Ports P1 and P2 (P1.0 to P1.7, P2.0 to P2.7)
- 5.9 Leakage Current – General-Purpose I/O (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7) (P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3, RST/NMI)
- 5.10 Outputs – General-Purpose I/O (Full Drive Strength) (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
- 5.11 Outputs – General-Purpose I/O (Reduced Drive Strength) (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
- 5.12 Output Frequency – General-Purpose I/O (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
- 5.13 Typical Characteristics – Outputs, Reduced Drive Strength (PxDS.y = 0)
- 5.14 Crystal Oscillator, XT1, Low-Frequency Mode
- 5.15 Crystal Oscillator, XT2
- 5.16 Internal Very-Low-Power Low-Frequency Oscillator (VLO)
- 5.17 Internal Reference, Low-Frequency Oscillator (REFO)
- 5.18 DCO Frequency
- 5.19 PMM, Brownout Reset (BOR)
- 5.20 PMM, Core Voltage
- 5.21 PMM, SVS High Side
- 5.22 PMM, SVM High Side
- 5.23 PMM, SVS Low Side
- 5.24 PMM, SVM Low Side
- 5.25 Wake-up Times From Low-Power Modes and Reset
- 5.26 Timer_A
- 5.27 Timer_B
- 5.28 USCI (UART Mode) Clock Frequency
- 5.29 USCI (UART Mode)
- 5.30 USCI (SPI Master Mode) Clock Frequency
- 5.31 USCI (SPI Master Mode)
- 5.32 USCI (SPI Slave Mode)
- 5.33 USCI (I2C Mode)
- 5.34 10-Bit ADC, Power Supply and Input Range Conditions
- 5.35 10-Bit ADC, Timing Parameters
- 5.36 10-Bit ADC, Linearity Parameters
- 5.37 REF, External Reference
- 5.38 REF, Built-In Reference
- 5.39 Comparator_B
- 5.40 Ports PU.0 and PU.1
- 5.41 LDO-PWR (LDO Power System)
- 5.42 Flash Memory
- 5.43 JTAG and Spy-Bi-Wire Interface
-
6Detailed Description
- 6.1 CPU (Link to User's Guide)
- 6.2 Operating Modes
- 6.3 Interrupt Vector Addresses
- 6.4 Memory Organization
- 6.5 Bootloader (BSL)
- 6.6 JTAG Operation
- 6.7 Flash Memory (Link to User's Guide)
- 6.8 RAM (Link to User's Guide)
- 6.9
Peripherals
- 6.9.1 Digital I/O (Link to User's Guide)
- 6.9.2 Port Mapping Controller (Link to User's Guide)
- 6.9.3 Oscillator and System Clock (Link to User's Guide)
- 6.9.4 Power-Management Module (PMM) (Link to User's Guide)
- 6.9.5 Hardware Multiplier (Link to User's Guide)
- 6.9.6 Real-Time Clock (RTC_A) (Link to User's Guide)
- 6.9.7 Watchdog Timer (WDT_A) (Link to User's Guide)
- 6.9.8 System Module (SYS) (Link to User's Guide)
- 6.9.9 DMA Controller (Link to User's Guide)
- 6.9.10 Universal Serial Communication Interface (USCI) (Links to User's Guide: UART Mode, SPI Mode, I2C Mode)
- 6.9.11 TA0 (Link to User's Guide)
- 6.9.12 TA1 (Link to User's Guide)
- 6.9.13 TA2 (Link to User's Guide)
- 6.9.14 TB0 (Link to User's Guide)
- 6.9.15 Comparator_B (Link to User's Guide)
- 6.9.16 ADC10_A (Link to User's Guide)
- 6.9.17 CRC16 (Link to User's Guide)
- 6.9.18 Reference (REF) Module Voltage Reference (Link to User's Guide)
- 6.9.19 LDO and Port U
- 6.9.20 Embedded Emulation Module (EEM) (S Version) (Link to User's Guide)
- 6.10 Peripheral File Map
- 6.11
Input/Output Diagrams
- 6.11.1 Port P1 (P1.0 to P1.7) Input/Output With Schmitt Trigger
- 6.11.2 Port P2 (P2.0 to P2.7) Input/Output With Schmitt Trigger
- 6.11.3 Port P3 (P3.0 to P3.4) Input/Output With Schmitt Trigger
- 6.11.4 Port P4 (P4.0 to P4.7) Input/Output With Schmitt Trigger
- 6.11.5 Port P5 (P5.0 and P5.1) Input/Output With Schmitt Trigger
- 6.11.6 Port P5 (P5.2) Input/Output With Schmitt Trigger
- 6.11.7 Port P5 (P5.3) Input/Output With Schmitt Trigger
- 6.11.8 Port P5 (P5.4 and P5.5) Input/Output With Schmitt Trigger
- 6.11.9 Port P6 (P6.0 to P6.7) Input/Output With Schmitt Trigger
- 6.11.10 Port U (PU.0 and PU.1) Input/Output
- 6.11.11 Port J (PJ.0) JTAG Pin TDO, Input/Output With Schmitt Trigger or Output
- 6.11.12 Port J (PJ.1 to PJ.3) JTAG Pins TMS, TCK, TDI/TCLK, Input/Output With Schmitt Trigger or Output
- 6.12 Device Descriptors
- 7器件和文档支持
- 8机械、封装和可订购信息
封装选项
机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息
6.11.5 Port P5 (P5.0 and P5.1) Input/Output With Schmitt Trigger
Figure 6-6 shows the port diagram. Table 6-47 summarizes the selection of the pin functions.
Figure 6-6 Port P5 (P5.0 and P5.1) Diagram Table 6-47 Port P5 (P5.0 and P5.1) Pin Functions
| PIN NAME (P5.x) | x | FUNCTION | CONTROL BITS OR SIGNALS(3) | |
|---|---|---|---|---|
| P5DIR.x | P5SEL.x | |||
| P5.0/A8/VeREF+(1) | 0 | P5.0 (I/O)(4) | I: 0; O: 1 | 0 |
| A8/VeREF+(5) | X | 1 | ||
| P5.1/A9/VeREF–(2) | 1 | P5.1 (I/O)(4) | I: 0; O: 1 | 0 |
| A9/VeREF–(6) | X | 1 | ||
(1) VeREF+ available on devices with ADC10_A.
(2) VeREF- available on devices with ADC10_A.
(3) X = Don't care
(4) Default condition
(5) Setting the P5SEL.0 bit disables the output driver and the input Schmitt trigger to prevent parasitic cross currents when applying analog signals. An external voltage can be applied to VeREF+ and used as the reference for the ADC10_A when available.
(6) Setting the P5SEL.1 bit disables the output driver and the input Schmitt trigger to prevent parasitic cross currents when applying analog signals. An external voltage can be applied to VeREF- and used as the reference for the ADC10_A when available.