米6体育平台手机版

ZHCSWB3A September 2000 – June 2024 OPA2241 , OPA2251 , OPA241 , OPA251 , OPA4241 , OPA4251

PRODUCTION DATA

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)

D|14

散热焊盘机械数据 (封装 | 引脚)

订购信息

5.7 Electrical Characteristics for V_S = ±15V

at T_A = 25°C, V_CM = V_OUT = midsupply, and R_L = 100kΩ connected to V_S / 2 (unless otherwise noted)

PARAMETER		TEST CONDITIONS		MIN	TYP	MAX	UNIT
OFFSET VOLTAGE
V_OS	Input offset voltage	OPAx241			±100		μV
		OPAx241	T_A = –40°C to +85°C		±150
		OPAx251			±50	±250
		OPAx251	T_A = –40°C to +85°C		±100	±300
dV_OS/dT	Input offset voltage drift	T_A = –40°C to +85°C	OPAx241		±0.6		μV/°C
dV_OS/dT	Input offset voltage drift	T_A = –40°C to +85°C	OPAx251		±0.5		μV/°C
PSRR	Power supply rejection ratio	V_S = 2.7V to 36V			±3	±30	μV/V
PSRR	Power supply rejection ratio	V_S = 2.7V to 36V	T_A = –40°C to +85°C			±30	μV/V
	Channel separation, (dual, quad)				0.3		μV/V
INPUT BIAS CURRENT
I_B	Input bias current⁽¹⁾				–4	–20	nA
I_B	Input bias current⁽¹⁾	T_A = –40°C to +85°C				–25	nA
I_OS	Input offset current				±0.1	±2	nA
I_OS	Input offset current	T_A = –40°C to +85°C				±2	nA
NOISE
	Input voltage noise	f = 0.1Hz to 10Hz			1.7		μV_PP
e_n	Input voltage noise density	f = 1kHz			65		nV/√Hz
i_n	Input current noise density	f = 1kHz			40		fA/√Hz
INPUT VOLTAGE
V_CM	Common-mode voltage			(V–) – 0.2		(V+) – 0.8	V
CMRR	Common-mode rejection ratio	–15.2V < V_CM < (V+) – 14.2V		100	124		dB
CMRR	Common-mode rejection ratio	–15V < V_CM < (V+) – 14.2V	T_A = –40°C to +85°C	100			dB
INPUT IMPEDANCE
Z_IN	Input impedance	Differential			10 \|\| 3.75		MΩ \|\| pF
Z_IN	Input impedance	Common-mode			1 \|\| 4		GΩ \|\| pF
OPEN-LOOP GAIN
A_OL	Open-loop voltage gain	(V–) + 250mV < V_O < (V+) – 250mV		100	128		dB
		(V–) + 250mV < V_O < (V+) – 250mV	T_A = –40°C to +85°C	100
		(V–) + 300mV < V_O < (V+) – 300mV, R_L = 20kΩ		100	128
		(V–) + 300mV < V_O < (V+) – 300mV, R_L = 20kΩ	T_A = –40°C to +85°C	100
FREQUENCY RESPONSE
GBW	Gain-bandwidth product				30		kHz
SR	Slew rate	V_S = 5V, G = 1V/V			0.01		V/μs
	Overload recovery time	V_S = V_IN × G			75		μs
OUTPUT
	Voltage output swing from rail⁽²⁾	A_OL > 100dB			50		mV
		A_OL > 100dB			75	250
		A_OL > 100dB	T_A = –40°C to +85°C			250
		A_OL > 100dB, R_L = 20kΩ,			100	300
		A_OL > 100dB, R_L = 20kΩ,	T_A = –40°C to +85°C			300
I_SC	Short-circuit current	Source	Single		4		mA
		Source	Dual		4
		Sink	Single		–21
		Sink	Dual		–27
C_LOAD	Capacitive load drive			See Typical Characteristics
POWER SUPPLY
I_Q	Quiescent current per amplifier	I_O = 0mA			±27	±38	μA
I_Q	Quiescent current per amplifier	I_O = 0mA	T_A = –40°C to +85°C			±45	μA

(1) The negative sign indicates input bias current flows out of the input terminals.

(2) Output voltage swings are measured between the output and power supply rails.

封装选项

机械数据 (封装 | 引脚)

散热焊盘机械数据 (封装 | 引脚)

订购信息

5.7 Electrical Characteristics for VS = ±15V

5.7 Electrical Characteristics for V_S = ±15V