SLASE64A December   2014  – June 2017 PCM1860-Q1 , PCM1861-Q1 , PCM1862-Q1 , PCM1863-Q1 , PCM1864-Q1 , PCM1865-Q1

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics: PGA and ADC AC Performance
    6. 7.6  Electrical Characteristics: DC
    7. 7.7  Electrical Characteristics: Digital Filter
    8. 7.8  Timing Requirements: External Clock
    9. 7.9  Timing Requirements: I2C Control Interface
    10. 7.10 Timing Requirements: SPI Control Interface
    11. 7.11 Timing Requirements: Audio Data Interface for Slave Mode
    12. 7.12 Timing Requirements: Audio Data Interface for Master Mode
    13. 7.13 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagrams
    3. 9.3 Features Description
      1. 9.3.1  Analog Front End
      2. 9.3.2  Microphone Support
        1. 9.3.2.1 Mic Bias
      3. 9.3.3  Input Multiplexer (PCM1860-Q1 and PCM1861-Q1)
      4. 9.3.4  Mixers and Multiplexers (PCM1862-Q1, PCM1863-Q1, PCM1864-Q1, and PCM1865-Q1)
      5. 9.3.5  Programmable Gain Amplifier
      6. 9.3.6  Automatic Clipping Suppression
        1. 9.3.6.1 Attenuation Level
        2. 9.3.6.2 Channel Linking
      7. 9.3.7  Zero Crossing Detect
      8. 9.3.8  Digital Inputs
        1. 9.3.8.1 Stereo PCM Sources
        2. 9.3.8.2 Digital PDM Microphones
      9. 9.3.9  Clocks
        1. 9.3.9.1 Description
        2. 9.3.9.2 External Clock-Source Limits
        3. 9.3.9.3 Device Clock Distribution and Generation
        4. 9.3.9.4 Clocking Modes
          1. 9.3.9.4.1 Clock Configuration and Selection for Hardware-Controlled Devices
          2. 9.3.9.4.2 Clock Sources for Software-Controlled Devices
          3. 9.3.9.4.3 Clocking Configuration and Selection for Software-Controlled Devices
            1. 9.3.9.4.3.1 Target Clock Rates for ADC, DSP1 and DSP2
            2. 9.3.9.4.3.2 Configuration of Master Mode
          4. 9.3.9.4.4 BCK Input Slave PLL Mode
          5. 9.3.9.4.5 Software-Controlled Devices ADC Non-Audio MCK PLL Mode
        5. 9.3.9.5 Software-Controlled Devices Manual PLL Calculation
        6. 9.3.9.6 Clock Halt and Error
        7. 9.3.9.7 Clock Halt and Error Detect
        8. 9.3.9.8 Changes in Clock Sources and Sample Rates
      10. 9.3.10 Analog-to-Digital Converters (ADCs)
        1. 9.3.10.1 Main Audio ADCs
        2. 9.3.10.2 Secondary ADC: Energysense and Analog Control
          1. 9.3.10.2.1 Secondary ADC Analog Input Range
          2. 9.3.10.2.2 Frequency Response of the Secondary ADC
        3. 9.3.10.3 Secondary ADC Controlsense DC Level Change Detection
      11. 9.3.11 Energysense
        1. 9.3.11.1 Energysense Signal Loss Flag
        2. 9.3.11.2 Energysense Signal Detect Circuitry
          1. 9.3.11.2.1 Energysense Threshold Levels for Both Signal Loss and Signal Detect
        3. 9.3.11.3 Programming Various Coefficients for Energysense
      12. 9.3.12 Audio Processing
        1. 9.3.12.1 DSP1 Processing Features
          1. 9.3.12.1.1 Digital Decimation Filters
          2. 9.3.12.1.2 Digital PGA
        2. 9.3.12.2 DSP2 Processing Features
          1. 9.3.12.2.1 Digital Mixing Function
      13. 9.3.13 Fade-In and Fade-Out Functions
      14. 9.3.14 Mappable GPIO Pins
      15. 9.3.15 Interrupt Controller
        1. 9.3.15.1 DIN Toggle Detection
        2. 9.3.15.2 Clearing Interrupts
          1. 9.3.15.2.1 Reset Energysense Loss (in Active Mode)
          2. 9.3.15.2.2 Reset Energysense Detect (In Sleep Mode)
          3. 9.3.15.2.3 Reset Controlsense (Active and Sleep Modes)
          4. 9.3.15.2.4 Reset DIN Toggle (In Sleep Mode)
          5. 9.3.15.2.5 Reset PGA Clipping (Active)
      16. 9.3.16 Audio Format Selection and Timing Details
        1. 9.3.16.1 Audio Format Selection
        2. 9.3.16.2 Serial Audio Interface Timing Details
        3. 9.3.16.3 Digital Audio Output 2 Configuration
        4. 9.3.16.4 Time Division Multiplex (TDM Support)
        5. 9.3.16.5 Decimation Filter Select
        6. 9.3.16.6 Serial Audio Data Interface Configuration
    4. 9.4 Device Functional Modes
      1. 9.4.1 Power Mode Descriptions
        1. 9.4.1.1 PCM1860-Q1 and PCM1861-Q1 Hardware Device Power Down Functions
          1. 9.4.1.1.1 Enter Standby Mode (From Active Mode)
          2. 9.4.1.1.2 Exit From Standby Mode Back to Active
          3. 9.4.1.1.3 Enter or Exit Sleep or Energysense Mode to Active
        2. 9.4.1.2 PCM186x-Q1 Software Device Power Down Functions
          1. 9.4.1.2.1 Enter or Exit Stand-by Mode
          2. 9.4.1.2.2 Enter Sleep Mode
          3. 9.4.1.2.3 Exit Sleep Mode
        3. 9.4.1.3 Bypassing the Internal LDO to Reduce Power Consumption
    5. 9.5 Programming
      1. 9.5.1 Control
        1. 9.5.1.1 Hardware Control Configuration
        2. 9.5.1.2 Software-Controlled Device Configuration
        3. 9.5.1.3 SPI Interface
          1. 9.5.1.3.1 Register Read and Write Operation
        4. 9.5.1.4 I2C Interface
          1. 9.5.1.4.1 Slave Address
          2. 9.5.1.4.2 Packet Protocol
      2. 9.5.2 Current Status Registers
      3. 9.5.3 Real World Software Configuration using Energysense and Controlsense
        1. 9.5.3.1 Active Mode Flow Diagram
        2. 9.5.3.2 Basic Device Configuration
        3. 9.5.3.3 Clear Energysense Interrupt
        4. 9.5.3.4 Update System Settings
        5. 9.5.3.5 Sleep Mode Flow Diagram
        6. 9.5.3.6 Update Controlsense values in Sleep Mode
          1. 9.5.3.6.1 Update System Settings
      4. 9.5.4 Programming and Register Reference
        1. 9.5.4.1 Coefficient Data Formats
      5. 9.5.5 Programming DSP Coefficients on Software-Controlled Devices
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Device Control Method
        1. 10.1.1.1 Hardware Control
        2. 10.1.1.2 Software Control
          1. 10.1.1.2.1 SPI Control
          2. 10.1.1.2.2 I2C Control
      2. 10.1.2 Power-Supply Options
        1. 10.1.2.1 3.3-V AVDD, DVDD, and IOVDD
        2. 10.1.2.2 3.3-V AVDD, DVDD, and 1.8-V IOVDD
      3. 10.1.3 Master Clock Source
      4. 10.1.4 Dual PCM186x-Q1 TDM Functionality
      5. 10.1.5 Analog Input Configuration
        1. 10.1.5.1 Analog Front-End Circuit For Single-Ended, Line-In Applications
        2. 10.1.5.2 Analog Front-End Circuit for Differential, Line-In Applications
    2. 10.2 Typical Applications
      1. 10.2.1 Stereo Recording Application for PCM186x-Q1 Hardware-Controlled Devices in Master Mode
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
        3. 10.2.1.3 Application Curves
      2. 10.2.2 Stereo Recording Application for PCM186x-Q1 Software-Controlled Devices in Slave PLL Mode with 1.8-V IOVDD
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
        3. 10.2.2.3 Application Curves
  11. 11Power Supply Recommendations
    1. 11.1 Power-Supply Distribution and Requirements
    2. 11.2 1.8-V Support
    3. 11.3 Brownout Conditions
    4. 11.4 Power-Up Sequence
    5. 11.5 Lowest Power-Down Modes
      1. 11.5.1 Lowest Power In Standby Mode (AVDD = DVDD = IOVDD = 3.3 V)
      2. 11.5.2 Lowest Power in Sleep or Energysense Mode (AVDD = DVDD = IOVDD = 3.3 V)
      3. 11.5.3 Lower Power in Sleep or Energysense Mode (AVDD = DVDD 3.3 V and IOVDD = 1.8 V)
    6. 11.6 Power-On Reset Sequencing Timing Diagram
    7. 11.7 Power Connection Examples
      1. 11.7.1 3.3-V AVDD, DVDD, and IOVDD Example
      2. 11.7.2 3.3-V AVDD, DVDD With 1.8-V IOVDD Example for Lower-Power Applications
    8. 11.8 Fade In
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Grounding and System Partitioning
    2. 12.2 Layout Example
  13. 13Register Map
    1. 13.1 Register Map Description
    2. 13.2 Register Map Summary
    3. 13.3 Page 0 Registers
      1. 13.3.1  Page 0: Register 1 (address = 0x01) [reset = 0x00]
      2. 13.3.2  Page 0: Register 2 (address = 0x02) [reset = 0x00]
      3. 13.3.3  Page 0: Register 3 (address = 0x03) [reset = 0x00]
      4. 13.3.4  Page 0: Register 4 (address = 0x04) [reset = 0x00]
      5. 13.3.5  Page 0: Register 5 (address = 0x05) [reset = 0x86]
      6. 13.3.6  Page 0: Register 6 (address = 0x06) [reset = 0x41]
      7. 13.3.7  Page 0: Register 7 (address = 0x07) [reset = 0x41]
      8. 13.3.8  Page 0: Register 8 (address = 0x08) [reset = 0x42]
      9. 13.3.9  Page 0: Register 9 (address = 0x09) [reset = 0x42]
      10. 13.3.10 Page 0: Register 10 (address = 0x0A) [reset = 0x00]
      11. 13.3.11 Page 0: Register 11 (address = 0x0B) [reset = 0x44]
      12. 13.3.12 Page 0: Register 12 (address = 0x0C) [reset = 0x00]
      13. 13.3.13 Page 0: Register 13 (address = 0x0D) [reset = 0x00]
      14. 13.3.14 Page 0: Register 14 (address = 0x0E) [reset = 0x00]
      15. 13.3.15 Page 0: Register 15 (address = 0x0F) [reset = 0x00]
      16. 13.3.16 Page 0: Register 16 (address = 0x10) [reset = 0x01]
      17. 13.3.17 Page 0: Register 17 (address = 0x11) [reset = 0x20]
      18. 13.3.18 Page 0: Register 18 (address = 0x12) [reset = 0x00]
      19. 13.3.19 Page 0: Register 19 (address = 0x13) [reset = 0x00]
      20. 13.3.20 Page 0: Register 20 (address = 0x14) [reset = 0x00]
      21. 13.3.21 Page 0: Register 21 (address = 0x15) [reset = 0x00]
      22. 13.3.22 Page 0: Register 22 (address = 0x16) [reset = 0x00]
      23. 13.3.23 Page 0: Register 23 (address = 0x17) [reset = 0x00]
      24. 13.3.24 Page 0: Register 24 (address = 0x18) [reset = 0x00]
      25. 13.3.25 Page 0: Register 25 (address = 0x19) [reset = 0x00]
      26. 13.3.26 Page 0: Register 26 (address = 0x1A) [reset = 0x00]
      27. 13.3.27 Page 0: Register 27 (address = 0x1B) [reset = 0x00]
      28. 13.3.28 Page 0: Register 32 (address = 0x20) [reset = 0x01]
      29. 13.3.29 Page 0: Register 33 (address = 0x21) [reset = 0x00]
      30. 13.3.30 Page 0: Register 34 (address = 0x22) [reset = 0x01]
      31. 13.3.31 Page 0: Register 35 (address = 0x23) [reset = 0x03]
      32. 13.3.32 Page 0: Register 37 (address = 0x25) [reset = 0x07]
      33. 13.3.33 Page 0: Register 38 (address = 0x26) [reset = 0x03]
      34. 13.3.34 Page 0: Register 39 (address = 0x27) [reset = 0x3F]
      35. 13.3.35 Page 0: Register 40 (address = 0x28) [reset = 0x01]
      36. 13.3.36 Page 0: Register 41 (address = 0x29) [reset = 0x00]
      37. 13.3.37 Page 0: Register 42 (address = 0x2A) [reset = 0x00]
      38. 13.3.38 Page 0: Register 43 (address = 0x2B) [reset = 0x01]
      39. 13.3.39 Page 0: Register 44 (address = 0x2C) [reset = 0x00]
      40. 13.3.40 Page 0: Register 45 (address = 0x2D) [reset = 0x00]
      41. 13.3.41 Page 0: Register 48 (address = 0x30) [reset = 0x00]
      42. 13.3.42 Page 0: Register 49 (address = 0x31) [reset = 0x00]
      43. 13.3.43 Page 0: Register 50 (address = 0x32) [reset = 0x00]
      44. 13.3.44 Page 0: Register 51 (address = 0x33) [reset = 0x00]
      45. 13.3.45 Page 0: Register 52 (address = 0x34) [reset = 0x00]
      46. 13.3.46 Page 0: Register 54 (address = 0x36) [reset = 0x01]
      47. 13.3.47 Page 0: Register 64 (address = 0x40) [reset =0x80]
      48. 13.3.48 Page 0: Register 65 (address = 0x41) [reset = 0x7F]
      49. 13.3.49 Page 0: Register 66 (address = 0x42) [reset = 0x00]
      50. 13.3.50 Page 0: Register 67 (address = 0x43) [reset = 0x80]
      51. 13.3.51 Page 0: Register 68 (address = 0x44) [reset = 0x7F]
      52. 13.3.52 Page 0: Register 69 (address = 0x45) [reset = 0x00]
      53. 13.3.53 Page 0: Register 70 (address = 0x46) [reset = 0x80]
      54. 13.3.54 Page 0: Register 71 (address = 0x47) [reset = 0x7F]
      55. 13.3.55 Page 0: Register 72 (address = 0x48) [reset = 0x00]
      56. 13.3.56 Page 0: Register 73 (address = 0x49) [reset = 0x80]
      57. 13.3.57 Page 0: Register 74 (address = 0x4A) [reset = 0x7F]
      58. 13.3.58 Page 0: Register 75 (address = 0x4B) [reset = 0x00]
      59. 13.3.59 Page 0: Register 76 (address = 0x4C) [reset = 0x80]
      60. 13.3.60 Page 0: Register 77 (address = 0x4D) [reset = 0x7F]
      61. 13.3.61 Page 0: Register 78 (address = 0x4E) [reset = 0x00]
      62. 13.3.62 Page 0: Register 79 (address = 0x4F) [reset = 0x80]
      63. 13.3.63 Page 0: Register 80 (address = 0x50) [reset = 0x7F]
      64. 13.3.64 Page 0: Register 81 (address = 0x51) [reset = 0x00]
      65. 13.3.65 Page 0: Register 82 (address = 0x52) [reset = 0x80]
      66. 13.3.66 Page 0: Register 83 (address = 0x53) [reset = 0x7F]
      67. 13.3.67 Page 0: Register 84 (address = 0x54) [reset = 0x00]
      68. 13.3.68 Page 0: Register 85 (address = 0x55) [reset = 0x80]
      69. 13.3.69 Page 0: Register 86 (address = 0x56) [reset = 0x7F]
      70. 13.3.70 Page 0: Register 87 (address = 0x57) [reset = 0x00]
      71. 13.3.71 Page 0: Register 88 (address = 0x58) [reset = 0x00]
      72. 13.3.72 Page 0: Register 89 (address = 0x59) [reset = 0x00]
      73. 13.3.73 Page 0: Register 90 (address = 0x5A) [reset = 0x00]
      74. 13.3.74 Page 0: Register 96 (address = 0x60) [reset = 0x01]
      75. 13.3.75 Page 0: Register 97 (address = 0x61) [reset = 0x00]
      76. 13.3.76 Page 0: Register 98 (address = 0x62) [reset =0x10]
      77. 13.3.77 Page 0: Register 112 (address = 0x70) [reset = 0x70]
      78. 13.3.78 Page 0: Register 113 (address = 0x71) [reset = 0x10]
      79. 13.3.79 Page 0: Register 114 (address = 0x72) [reset = 0x00]
      80. 13.3.80 Page 0: Register 115 (address = 0x73) [reset = 0x00]
      81. 13.3.81 Page 0: Register 116 (address = 0x74) [reset = 0x00]
      82. 13.3.82 Page 0: Register 117 (address = 0x75) [reset = 0x00]
      83. 13.3.83 Page 0: Register 120 (address = 0x78) [reset = 0x00]
    4. 13.4 Page 1 Registers
      1. 13.4.1  Page 1: Register 1 (address = 0x01) [reset = 0x00]
      2. 13.4.2  Page 1: Register 2 (address = 0x02) [reset = 0x00]
      3. 13.4.3  Page 1: Register 4 (address = 0x04) [reset = 0x00]
      4. 13.4.4  Page 1: Register 5 (address = 0x05) [reset = 0x00]
      5. 13.4.5  Page 1: Register 6 (address = 0x06) [reset = 0x00]
      6. 13.4.6  Page 1: Register 7 (address = 0x07) [reset = 0x00]
      7. 13.4.7  Page 1: Register 8 (address = 0x08) [reset = 0x00]
      8. 13.4.8  Page 1: Register 9 (address = 0x09) [reset = 0x00]
      9. 13.4.9  Page 1: Register 10 (address = 0x0A) [reset = 0x00]
      10. 13.4.10 Page 1: Register 11 (address = 0x0B) [reset = 0x00]
    5. 13.5 Page 3 Registers
      1. 13.5.1 Page 3: Register 18 (address = 0x12) [reset =0x40]
      2. 13.5.2 Page 3: Register 21 (address = 0x15) [reset = 0x01]
    6. 13.6 Page 253 Registers
      1. 13.6.1 Page 253: Register 20 (address = 0x14) [reset = 0x00]
  14. 14Device and Documentation Support
    1. 14.1 Development Support
    2. 14.2 Related Links
    3. 14.3 Receiving Notification of Documentation Updates
    4. 14.4 Community Resources
    5. 14.5 Trademarks
    6. 14.6 Electrostatic Discharge Caution
    7. 14.7 Glossary
  15. 15Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6 Pin Configuration and Functions

DBT Package: PCM1860-Q1 and PCM1861-Q1
30-Pin TSSOP
Top View

Pin Functions: PCM1860-Q1 and PCM1861-Q1

PIN TYPE DESCRIPTION
NO. NAME
1 VINL2/VIN1M Analog input Analog input 2, L-channel (or differential M input for input 1)
2 VINR2/VIN2M Analog input Analog input 2, R-channel (or differential M input for input 2)
3 VINL1/VIN1P Analog input Analog input 1, L-channel (or differential P input for input 1)
4 VINR1/VIN2P Analog input Analog input 1, R-channel (or differential P input for input 2)
5 Mic Bias Power Microphone bias output
6 VREF Power Reference voltage output decoupling point (typically, 0.5 AVDD). Connect 1-µF capacitor from this pin to AGND.
7 AGND Power Analog ground
8 AVDD Power Analog power supply (typically, 3.3 V). Connect 0.1-µF and 10-µF capacitors from this pin to AGND.
9 XO Digital output Crystal oscillator output
10 XI Digital input Crystal oscillator input or master clock input (1.8-V CMOS signal)
11 LDO Power Internal low-dropout regulator (LDO) decoupling output, or external 1.8-V input to bypass LDO. Connect 0.1-µF and 10-µF capacitors from this pin to DGND.
12 DGND Power Digital ground
13 DVDD Power Digital power supply (typically, 3.3 V). Connect 0.1-µF and 10-µF capacitors from this pin to DGND.
14 IOVDD Power Power supply for I/O voltages (typically, 3.3 V or 1.8 V).
15 SCKI Digital input CMOS level (3.3 V) master clock input
16 LRCK Digital input/output Audio data word clock (left right clock) input/output(1)
17 BCK Digital input/output Audio data bit clock input/output(1)
18 DOUT Digital output Audio data digital output
19 INT Analog output Interrupt output (for analog input detection). Pull high for active mode, pull low for idle.
20 MD6 Analog input Analog MUX and gain selection using MD6, MD5, and MD2 pins, respectively:
000: SE Ch 1 (VINL1 and VINR1)
001: SE Ch 2 (VINL2 and VINR2)
010: SE Ch 3 (VINL3 and VINR3)
011: SE Ch 4 (VINL4 and VINR4)
100: SE Ch 4 with 12-dB gain
101: SE Ch 4 with 32-dB gain
110: Diff Ch 1 (VIN1P and VIN1M, VIN2P and VIN2M)
111: Diff Ch 2 (VIN3P and VIN3M, VIN4P and VIN4M) with 12-dB gain
21 MD5 Analog input Analog MUX and gain selection (see MD6 pin for description)
22 MD4 Analog input Audio format: high = left-justified, low = I2S
23 MD2 Analog input Analog MUX and gain selection (see MD6 pin for description)
24 MD3 Digital Input Filter select: 0 = FIR decimation filter, 1 = IIR low latency decimation filter
25 MD1 Analog input Audio interface mode selection using MD1 and MD0 pins, respectively:
00: Slave mode, 256 × fS, 384 × fS, 512 × fS autodetect
01: Master mode (512 × fS)
10: Master mode (384 × fS)
11: Master mode (256 × fS)
26 MD0 Analog input Audio interface mode selection (see MD1 pin for description)
27 VINL4/VIN4M Analog input Analog input 4, L-channel (or differential M input for input 4)
28 VINR4/VIN3M Analog input Analog input 4, R-channel (or differential M input for input 3)
29 VINL3/VIN4P Analog input Analog input 3, L-channel (or differential P input for input 4)
30 VINR3/VIN3P Analog input Analog input 3, R-channel (or differential P input for input 3)
(1) Schmitt trigger input with internal pull-down (50 kΩ, typically).
DBT Package: PCM1862-Q1, PCM1863-Q1, PCM1864-Q1, and PCM1865-Q1
30-Pin TSSOP
Top View
NOTE: The DMIN2 option for pin 22 is only available on the PCM1864-Q1 and PCM1865-Q1 devices.

Pin Functions: PCM1862-Q1, PCM1863-Q1, PCM1864-Q1, and PCM1865-Q1

PIN TYPE DESCRIPTION
NO. NAME
1 VINL2/VIN1M Analog input Analog input 2, L-channel (or differential M input for input 1)
2 VINR2/VIN2M Analog input Analog input 2, R-channel (or differential M input for input 2)
3 VINL1/VIN1P Analog input Analog input 1, L-channel (or differential P input for input 1)
4 VINR1/VIN2P Analog input Analog input 1, R-channel (or differential P input for input 2)
5 Mic Bias Power Microphone bias output
6 VREF Power Reference voltage output decoupling point (typically, 0.5 AVDD). Connect 1-µF capacitor from this pin to AGND.
7 AGND Power Analog ground
8 AVDD Power Analog power supply (typically, 3.3 V). Connect 0.1-µF and 10-µF capacitors from this pin to AGND.
9 XO Digital output Crystal oscillator output
10 XI Digital input Crystal oscillator input or master clock input (1.8-V CMOS signal)
11 LDO Power Internal LDO decoupling output, or external 1.8-V input to bypass LDO. Connect 0.1-µF and 10-µF capacitors from this pin to DGND.
12 DGND Power Digital ground
13 DVDD Power Digital power supply (typically, 3.3 V). Connect 0.1-µF and 10-µF capacitors from this pin to DGND.
14 IOVDD Power Power supply for I/O voltages (typically, 3.3 V or 1.8 V).
15 SCKI Digital input CMOS level (3.3 V) master clock input
16 LRCK Digital input/output Audio data world clock (left right clock) input/output(1)
17 BCK Digital input/output Audio data bit clock input/output(1)
18 DOUT Analog output Audio data digital output
19 GPIO3/INTC Digital input/output GPIO 3 or interrupt C
20 GPIO2/INTB/DMCLK Digital input/output GPIO 2, interrupt B, or digital microphone clock output
21 GPIO1/INTA/DMIN Digital input/output GPIO 1, interrupt A, or digital microphone input
22 MISO/GPIO0/DMIN2 Digital input/output In SPI mode: master in, slave out
In I2C mode: GPIO0 (or DMIN2 for PCM1864-Q1 and PCM1865-Q1 only)
23 MOSI/SDA Digital input/output In SPI mode: master out, slave in
In I2C mode: SDA
24 MC/SCL Digital input In SPI mode: serial bit clock
In I2C mode: serial bit clock
25 MS/AD Digital input In SPI mode: chip select
In I2C mode: address pin
26 MD0 Digital input Control method select pin: I2C (tied low or not connected) or SPI (tied high)
27 VINL4/VIN4M Analog input Analog input 4, L-channel (or differential M input for input 4)
28 VINR4/VIN3M Analog input Analog input 4, R-channel (or differential M input for input 3)
29 VINL3/VIN4P Analog input Analog input 3, L-channel (or differential P input for input 4)
30 VINR3/VIN3P Analog input Analog input 3, R-channel (or differential P input for input 3)
(1) Schmitt trigger input with internal pull-down (50 kΩ, typically).
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |