9 Revision History

Changes from Revision G (November 2014) to Revision H (October 2024)

• 更新了特性、应用、说明、详细说明、特性说明、详细设计过程 和布局指南 部分，用于反映“规格”部分中列出的更改Go
• 将器件信息 表更改为封装信息 Go
• Removed Duration of output short circuit to ground specification and added maximum output current of ±125mA in Absolute Maximum Ratings tableGo
• Updated Handling Ratings table to ESD Ratings tableGo
• Updated Thermal Information tableGo
• Changed the typical input offset voltage value from: 0.5mV to 0.3mV in the Electrical Characteristics tableGo
• Changed the typical Input bias current value from: 150nA to 80nA in the Electrical Characteristics tableGo
• Changed the typical maximum output voltage swing value at R_L = 10kΩ from ±14V to ±14.1V in the Electrical Characteristics tableGo
• Changed the typical maximum output voltage swing value at R_L = 2kΩ from: ±13V to ±13.8V in the Electrical Characteristics tableGo
• Changed the typical large-signal differential voltage amplification value from: 300V/mV to 830V/mV in the Electrical Characteristics tableGo
• Added line items for the large-signal voltage amplification parameter to show values in dB units in the Electrical Characteristics tableGo
• Changed unity gain-bandwidth parameter to gain-bandwidth product and changed the typical value from: 3MHz to 4MHz in the Electrical Characteristics tableGo
• Added the small-signal bandwidth parameter in the Electrical Characteristics tableGo
• Added test condition to the common-mode rejection ratio parameter in the Electrical Characteristics tableGo
• Changed the typical common-mode rejection ratio value from: 90dB to 94dB in the Electrical Characteristics tableGo
• Removed the minimum limit for the input resistance parameter in the Electrical Characteristics tableGo
• Updated the input resistance parameter to input impedance to better reflect device characteristics in the Electrical Characteristics tableGo
• Changed the test condition of the supply-voltage sensitivity parameter from: V_CC = ±15V to ±9V to V_CC = ±5V to ±15V in the Electrical Characteristics tableGo
• Updated the typical supply-voltage sensitivity value from: 30µV/V to 25µV/V in the Electrical Characteristics tableGo
• Added line items for supply-voltage sensitivity parameter to show values in dB units in the Electrical Characteristics tableGo
• Added input voltage noise parameter to the Electrical Characteristics tableGo
• Changed test conditions of equivalent input noise voltage (closed loop) parameter to f = 1 kHz in the Electrical Characteristics tableGo
• Changed typical equivalent input noise voltage (closed loop) at f = 1 kHz from 8 nV/√Hz to 7 nV/√Hz in the Electrical Characteristics tableGo
• Changed equivalent input noise voltage (closed loop) specification to input voltage noise density in the Electrical Characteristics tableGo
• Added f = 10 kHz test condition to equivalent input noise voltage (closed loop) specification in the Electrical Characteristics tableGo
• Added the input current noise density parameter to the Electrical Characteristics tableGo
• Removed the total power dissipation parameter in the Electrical Characteristics tableGo
• Changed T_A min and T_A max conditions for supply current to one full range temperature condition in the Electrical Characteristics tableGo
• Changed the typical supply current (both amplifiers) value at full temperature range from: 3 mA to 2.65 mA in the Electrical Characteristics tableGo
• Changed the test condition for the crosstalk attenuation parameter from Open loop & A_VD = 100 V/V to A_VD = 1V/V in the Electrical Characteristics tableGo
• Changed the typical crosstalk attenuation value from: 105dB to 120 dB in the Electrical Characteristics tableGo
• Changed the rise time typical value from: 0.13 ns to 67 ns in the Electrical Characteristics tableGo
• Changed the overshoot typical value from: 5% to 16.8% in the Electrical Characteristics tableGo
• Changed the slew rate typical value from: 1.7V/µs to 2.2V/µs in the Electrical Characteristics tableGo
• Changed and added graphs to the Typical Characteristics sectionGo