米6体育平台手机版

ZHCSE15F July 2015 – May 2018 SN65DP159 , SN75DP159

PRODUCTION DATA.

封装选项

机械数据 (封装 | 引脚)

RSB|40
- MPQF185C
RGZ|48
- MPQF123F

散热焊盘机械数据 (封装 | 引脚)

RSB|40
- QFND255H
RGZ|48
- QFND014T

订购信息

11.1 Power Management

To minimize the power consumption of customer application, SNx5DP159 uses dual power supply. V_CC is 3.3-V with 10% range to support the I/O voltage. The V_DD is 1.00-V to 1.27-V range to supply the internal digital control circuit. v operates in two different working states. See Table 14 for conditions for each mode. When OE is deasserted and then reasserted the device will rest to its default configurations. If different configurations were programmed using I²C then the device will have to be reprogrammed.

Power-down mode:
- OE = Low puts the device into its lowest power state by shutting down all function blocks
  - When OE is re-asserted the transitions from L → H will create a reset and if the device is programmed through I²C it will have to be reprogrammed.
  - OE = High, HPD_SNK = Low
  - Writing a 1 to register 09h[3]
Normal operation: Working in redriver or retimer
When HPD asserts, the device CDR and output will enable based on the signal detector circuit result
HPD_SRC = HPD_SNK in all conditions. The HPD channel operational when V_CC over 3-V.

NOTE

When the SNx5DP159 is put into a power down state using the OE pin the I²C registers are cleared. The TMDS_CLOCK_RATIO_STATUS bit will be cleared in all power down states. If cleared and HDMI2.0 resolutions are to be supported, the SNx5DP159 expects the source to write a 1 to this bit location. If this does not happen the PLL will not be set properly and no video may be evident.

Table 14. Control Logic and Mode of Operation

INPUTS⁽¹⁾		STATUS							MODE
HPD_SNK	OE	Mode of Operation	HPD_SRC	IN_Dx	SDA_CTL SCL_CTL	OUT_Dx OUT_CLK	DDC	AUX_SRC± (48 PIN ONLY)	MODE
H	L	X	H	High-Z	Disabled	High-Z	Disabled	Disable	Power-down mode
L	H	X	L	High-Z	Active	High-Z	Disabled	Disable	Power-down mode
H	H	X	H	High-Z	Active	High-Z	Disabled	Disable	Power-down mode when a one is written to 09h[3]
H	H	Redriver	H	RX active	Active	TX active	Active	Active	Normal operation
H	H	Retimer	H	RX active	Active	TX active	Active	Active	Normal operation

(1) L = LOW, H = HIGH

TMDS output termination control impacts the operating power.

Table 15. Control Logic and Mode of Operation

INPUTS⁽¹⁾		STATUS						MODE
HPD_SNK	OE	Mode of Operation	HPD_SRC	IN_Dx	SDA_CTL SCL_CTL	OUT_Dx OUT_CLK	DDC	MODE
H	L	X	H	High-Z	Disabled	High-Z	Disabled	Power-down mode
L	H	X	L	High-Z	Active	High-Z	Disabled	Power-down mode
H	H	X	H	High-Z	Active	High-Z	Disabled	Power-down mode when a one is written to 09h[3]
H	H	Redriver	H	RX active	Active	TX active	Active	Normal operation
H	H	Retimer	H	RX active	Active	TX active	Active	Normal operation

(1) L = LOW, H = HIGH

TMDS output termination control impacts the operating power.