ZHCSIC2H October   2019  – January 2023 TAS5825M

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
      1. 7.7.1 Bridge Tied Load (BTL) Configuration Curves with Hybrid Modulation
      2. 7.7.2 Parallel Bridge Tied Load (PBTL) Configuration With Hybrid Modulation
      3. 7.7.3 Bridge Tied Load (BTL) Configuration Curves with BD Modulation
      4. 7.7.4 Parallel Bridge Tied Load (PBTL) Configuration With BD Modulation
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Power Supplies
      2. 9.3.2 Device Clocking
      3. 9.3.3 Serial Audio Port – Clock Rates
      4. 9.3.4 Clock Halt Auto-Recovery
      5. 9.3.5 Sample Rate on the Fly Change
      6. 9.3.6 Serial Audio Port - Data Formats and Bit Depths
      7. 9.3.7 Digital Audio Processing
      8. 9.3.8 Class D Audio Amplifier
        1. 9.3.8.1 Speaker Amplifier Gain Select
        2. 9.3.8.2 Class D Loop Bandwidth and Switching Frequency Setting
    4. 9.4 Device Functional Modes
      1. 9.4.1 Software Control
      2. 9.4.2 Speaker Amplifier Operating Modes
        1. 9.4.2.1 BTL Mode
        2. 9.4.2.2 PBTL Mode
      3. 9.4.3 Low EMI Modes
        1. 9.4.3.1 Spread Spectrum
        2. 9.4.3.2 Channel to Channel Phase Shift
        3. 9.4.3.3 Multi-Devices PWM Phase Synchronization
          1. 9.4.3.3.1 Phase Synchronization With I2S Clock In Startup Phase
          2. 9.4.3.3.2 Phase Synchronization With GPIO
      4. 9.4.4 Thermal Foldback
      5. 9.4.5 Device State Control
      6. 9.4.6 Device Modulation
        1. 9.4.6.1 BD Modulation
        2. 9.4.6.2 1SPW Modulation
        3. 9.4.6.3 Hybrid Modulation
    5. 9.5 Programming and Control
      1. 9.5.1 I2 C Serial Communication Bus
      2. 9.5.2 I2 C Target Address
        1. 9.5.2.1 Random Write
        2. 9.5.2.2 Sequential Write
        3. 9.5.2.3 Random Read
        4. 9.5.2.4 Sequential Read
        5. 9.5.2.5 DSP Memory Book, Page and BQ update
        6. 9.5.2.6 Checksum
          1. 9.5.2.6.1 Cyclic Redundancy Check (CRC) Checksum
          2. 9.5.2.6.2 Exclusive or (XOR) Checksum
      3. 9.5.3 Control via Software
        1. 9.5.3.1 Startup Procedures
        2. 9.5.3.2 Shutdown Procedures
        3. 9.5.3.3 Protection and Monitoring
          1. 9.5.3.3.1 Overcurrent Limit (Cycle-By-Cycle)
          2. 9.5.3.3.2 Overcurrent Shutdown (OCSD)
          3. 9.5.3.3.3 DC Detect
    6. 9.6 Register Maps
      1. 9.6.1 CONTROL PORT Registers
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Inductor Selections
      2. 10.1.2 Bootstrap Capacitors
      3. 10.1.3 Power Supply Decoupling
      4. 10.1.4 Output EMI Filtering
    2. 10.2 Typical Applications
      1. 10.2.1 2.0 (Stereo BTL) System
      2. 10.2.2 Design Requirements
      3. 10.2.3 Detailed Design procedures
        1. 10.2.3.1 Step One: Hardware Integration
        2. 10.2.3.2 Step Two: Hardware Integration
        3. 10.2.3.3 Step Three: Software Integration
      4. 10.2.4 Application Curves
      5. 10.2.5 MONO (PBTL) Systems
      6. 10.2.6 Advanced 2.1 System (Two TAS5825M Devices)
      7. 10.2.7 Application Curves
    3. 10.3 Power Supply Recommendations
      1. 10.3.1 DVDD Supply
      2. 10.3.2 PVDD Supply
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
        1. 10.4.1.1 General Guidelines for Audio Amplifiers
        2. 10.4.1.2 Importance of PVDD Bypass Capacitor Placement on PVDD Network
        3. 10.4.1.3 Optimizing Thermal Performance
          1. 10.4.1.3.1 Device, Copper, and Component Layout
          2. 10.4.1.3.2 Stencil Pattern
            1. 10.4.1.3.2.1 PCB footprint and Via Arrangement
            2. 10.4.1.3.2.2 Solder Stencil
      2. 10.4.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Device Nomenclature
      2. 11.1.2 Development Support
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 支持资源
    4. 11.4 Trademarks
    5. 11.5 静电放电警告
    6. 11.6 术语表
  12. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.7.2 Parallel Bridge Tied Load (PBTL) Configuration With Hybrid Modulation

Free-air room temperature 25°C (unless otherwise noted) Measurements were made using TAS5825MEVM board and Audio Precision System 2722 with Analog Analyzer filter set to 20-kHz brickwall filter. All measurements taken with audio frequency set to 1 kHz and device PWM frequency set to 384 kHz, the LC filter used was 10 μH / 0.68 μF （Pre-Filter PBTL, the merging of the two output channels in this device can be done before the inductor portion of the output filter, see connect method in Section 10.2.5）, unless otherwise noted.

GUID-ABDAD28F-18D7-4128-815D-5DD69FD34D48-low.gif
Hybrid Modulation PO = 1W,2.5W,5W
FSW = 384 kHz Load = 4 Ω PBTL Mode
Figure 7-23 THD+N vs Frequency-PBTL
GUID-7308C9AD-9EF3-4F29-865C-8F0EDDC8F1AC-low.gif
Hybrid Modulation PO = 1W,2.5W,5W
FSW = 384 kHz Load = 4 Ω PBTL Mode
Figure 7-25 THD+N vs Frequency-PBTL
GUID-3347BB6A-AB92-4227-8F38-48B662338F20-low.gif
Hybrid Modulation PO = 1W,2.5W,5W
FSW = 384 kHz Load = 4 Ω PBTL Mode
Figure 7-27 THD+N vs Frequency-PBTL
GUID-34B4A7AB-F1A7-49F4-A567-4A0CDD6D2718-low.gif
Hybrid Modulation
FSW = 384 kHz Load = 4 Ω, 3 Ω PBTL Mode
Figure 7-29 THD+N vs Output Power-PBTL
GUID-8B1479CE-6E07-425B-9696-53BD0D517309-low.gif
Hybrid Modulation
FSW = 384 kHz Load = 4 Ω, 3 Ω PBTL Mode
Figure 7-31 THD+N vs Output Power-PBTL
GUID-8DF18A98-3B69-401C-8941-64A7EF1B370D-low.gif
Hybrid Modulation
FSW = 384 kHz Load = 3 Ω PBTL Mode
Figure 7-33 Efficiency vs Output Power
GUID-6063EBE7-129C-4F54-B20C-5C52ADB454C5-low.gif
Hybrid Modulation
FSW = 384 kHz Load = 3 Ω, 4 Ω PBTL Mode
Figure 7-35 Output Power vs Supply Voltage
GUID-EA971799-60BF-4E58-B692-3F0B9EEE3908-low.gif
Hybrid Modulation PO = 1W,2.5W,5W
FSW = 384 kHz Load = 3 Ω PBTL Mode
Figure 7-24 THD+N vs Frequency-PBTL
GUID-7746614B-001D-4857-8E4F-7171BEBF6857-low.gif
Hybrid Modulation PO = 1W, 2.5W, 5W
FSW = 384 kHz Load = 3 Ω PBTL Mode
Figure 7-26 THD+N vs Frequency-PBTL
GUID-AF856929-1DF1-4F6B-98C2-8FC018EC9ACC-low.gif
Hybrid Modulation PO = 1W,2.5W,5W
FSW = 384 kHz Load = 3 Ω PBTL Mode
Figure 7-28 THD+N vs Frequency-PBTL
GUID-84D7E4D5-78D0-4299-80CA-33EBF3F1E699-low.gif
Hybrid Modulation
FSW = 384 kHz Load = 4 Ω, 3 Ω PBTL Mode
Figure 7-30 THD+N vs Output Power-PBTL
GUID-8B96A25A-8DEF-4483-AB8D-C16940727B7D-low.gif
Hybrid Modulation
FSW = 384 kHz Load = 4- Ω PBTL Mode
Figure 7-32 Efficiency vs Output Power
GUID-876E04E1-9665-4004-ABC1-321011C591D2-low.gif
Hybrid Modulation
FSW = 384 kHz Load = 6 Ω PBTL Mode
Figure 7-34 Idle Channel Noise vs Supply Voltage
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |