ZHCSIR6C September   2018  – February 2022 TCAN1046V-Q1

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  ESD Ratings - IEC Ratings
    4. 6.4  Recommended Operating Conditions
    5. 6.5  Thermal Characteristics
    6. 6.6  Supply Characteristics
    7. 6.7  Dissipation Ratings
    8. 6.8  Electrical Characteristics
    9. 6.9  Switching Characteristics
    10. 6.10 Typical Characteristics
  7. 7 Parameter Measurement Information
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Pin Description
        1. 8.3.1.1 TXD1 and TXD2
        2. 8.3.1.2 GND1 and GND2
        3. 8.3.1.3 VCC
        4. 8.3.1.4 RXD1 and RXD2
        5. 8.3.1.5 VIO
        6. 8.3.1.6 CANH and CANL
        7. 8.3.1.7 STB1 and STB2 (Standby)
      2. 8.3.2 CAN Bus States
      3. 8.3.3 TXD Dominant Timeout (DTO)
      4. 8.3.4 CAN Bus Short Circuit Current Limiting
      5. 8.3.5 Thermal Shutdown (TSD)
      6. 8.3.6 Undervoltage Lockout
      7. 8.3.7 Unpowered Device
      8. 8.3.8 Floating pins
    4. 8.4 Device Functional Modes
      1. 8.4.1 Operating Modes
      2. 8.4.2 Normal Mode
      3. 8.4.3 Standby Mode
        1. 8.4.3.1 Remote Wake Request via Wake-Up Pattern (WUP) in Standby Mode
      4. 8.4.4 Driver and Receiver Function
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 CAN Termination
      2. 9.2.2 Detailed Design Procedures
        1. 9.2.2.1 Bus Loading, Length and Number of Nodes
      3. 9.2.3 Application Curves
    3. 9.3 System Examples
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 接收文档更新通知
    2. 12.2 支持资源
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 术语表
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.8 Electrical Characteristics

Over recommended operating conditions with TA = -40℃ to 125℃ (unless otherwise noted); CAN electrical parameters apply to both channels
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Driver Electrical Characteristics
VO(DOM) Dominant output voltage Normal mode CANH TXD = 0 V, STB = 0 V, 50 Ω ≤ RL ≤ 65 Ω, CL = open, RCM = open
See Figure 7-2 and Figure 8-3,		 2.75 4.5 V
CANL 0.5 2.25 V
VO(REC) Recessive output voltage Normal mode CANH and CANL TXD = VIO, STB = 0 V, RL = open (no load), RCM = open
See Figure 7-2 and Figure 8-3		 2 0.5 VCC 3 V
VSYM Driver symmetry
(VO(CANH) + VO(CANL))/VCC		 STB = 0 V, RL = 60 Ω, CSPLIT = 4.7 nF, CL = open, RCM = open, TXD = 250 kHz, 1 MHz, 2.5 MHz
See Figure 7-2 and Figure 9-2		 0.9 1.1 V/V
VSYM_DC DC output symmetry
(VCC - VO(CANH) - VO(CANL))		 STB = 0 V, RL = 60 Ω, CL = open
See Figure 7-2 and Figure 8-3		 –400 400 mV
VOD(DOM) Differential output voltage Normal mode
Dominant		 CANH - CANL TXD = 0 V, STB = 0 V, 50 Ω ≤ RL ≤ 65 Ω, CL = open
See Figure 7-2 and Figure 8-3		 1.5 3 V
TXD = 0 V, STB = 0 V, 45 Ω ≤ RL ≤ 70 Ω, CL = open
See Figure 7-2 and Figure 8-3		 1.4 3.3 V
TXD = 0 V, STB = 0 V, RL = 2240 Ω, CL = open
See Figure 7-2 and Figure 8-3		 1.5 5 V
VOD(REC) Differential output voltage Normal mode
Recessive		 CANH - CANL TXD = VIO, STB = 0 V, RL = 60 Ω, CL = open
See Figure 7-2 and Figure 8-3		 –120 12 mV
TXD = VIO, STB = 0 V, RL = open, CL = open
See Figure 7-2 and Figure 8-3		 –50 50 mV
VO(STB) Bus output voltage
Standby mode		 CANH STB = VIO, RL = open (no load)
See Figure 7-2 and Figure 8-3		 -0.1 0.1 V
CANL -0.1 0.1 V
CANH - CANL -0.2 0.2 V
IOS(SS_DOM) Short-circuit steady-state output current, dominant
Normal mode		 STB = 0 V, V(CANH) = -15 V to 40 V, CANL = open, TXD = 0 V
See Figure 7-7 and Figure 8-3		 –115 mA
STB = 0 V, V(CAN_L) = -15 V to 40 V, CANH = open, TXD = 0 V
See Figure 7-7 and Figure 8-3		 115 mA
IOS(SS_REC) Short-circuit steady-state output current, recessive
Normal mode		 STB = 0 V, –27 V ≤ VBUS ≤ 32 V, where VBUS = CANH = CANL, TXD = VIO
See Figure 7-7 and Figure 8-3		 –5 5 mA
Receiver Electrical Characteristics
VIT Input threshold voltage
Normal mode 		STB = 0 V, -12 V ≤ VCM ≤ 12 V
See Figure 7-3, Table 7-1, and Table 8-5 		500 900 mV
VIT(STB) Input threshold
Standby mode		 STB = VIO, -12 V ≤ VCM ≤ 12 V
See Figure 7-3, Table 7-1, and Table 8-5 		400 1150 mV
VDOM Dominant state differential input voltage range
Normal mode		 STB = 0 V, -12 V ≤ VCM ≤ 12 V
See Figure 7-3, Table 7-1, and Table 8-5 		0.9 9 V
VREC Recessive state differential input voltage range
Normal mode		 STB = 0 V, -12 V ≤ VCM ≤ 12 V
See Figure 7-3, Table 7-1, and Table 8-5 		-4 0.5 V
VDOM(STB) Dominant state differential input voltage range
Standby mode		 STB = VIO, -12 V ≤ VCM ≤ 12 V
See Figure 7-3, Table 7-1, and Table 8-5 		1.15 9 V
VREC(STB) Recessive state differential input voltage range
Standby mode		 STB = VIO, -12 V ≤ VCM ≤ 12 V
See Figure 7-3, Table 7-1, and Table 8-5 		-4 0.4 V
VHYS Hysteresis voltage for input threshold
Normal mode		 STB = 0 V, -12 V ≤ VCM ≤ 12 V
See Figure 7-3, Table 7-1, and Table 8-5 		100 mV
VCM Common mode range
Normal and standby modes		 See Figure 7-3 and Table 8-5Table 8-5 –12 12 V
ILKG(IOFF) Unpowered bus input leakage current CANH = CANL = 5 V, VCC = VIO = GND 5 µA
CI Input capacitance to ground (CANH or CANL) TXD = VIO(1)

 20 pF
CID Differential input capacitance 10 pF
RID Differential input resistance TXD = VIO(1), STB = 0 V, -12 V ≤ VCM ≤ 12 V 40 90 kΩ
RIN Single ended input resistance
(CANH or CANL)		 20 45 kΩ
TXD Terminal (CAN Transmit Data Input)
VIH High-level input voltage 0.7 VIO V
VIL Low-level input voltage 0.3 VIO V
IIH High-level input leakage current TXD = VCC = VIO = 5.5 V –2.5 0 1 µA
IIL Low-level input leakage current TXD = 0 V, VCC= VIO = 5.5 V –200 -100 –20 µA
ILKG(OFF) Unpowered leakage current TXD = 5.5 V, VCC= VIO = 0 V –1 0 1 µA
RXD Terminal (CAN Receive Data Output)
VOH High-level output voltage IO = –2 mA,
See Figure 7-3		 0.8 VIO V
VOL Low-level output voltage IO = –2 mA,
See Figure 7-3		 0.2 VIO V
STB Terminal (Standby Mode Input)
VIH High-level input voltage 0.7 VIO V
VIL Low-level input voltage 0.3 VIO V
IIH High-level input leakage current VCC = VIO = STB = 5.5 V –2 2 µA
IIL Low-level input leakage current VCC = VIO = 5.5 V, STB = 0 V –20 –2 µA
ILKG(OFF) Unpowered leakage current STB = 5.5V, VCC = VIO = 0 V –1 0 1 µA
(1) VIO = VCC in non-V variants of device
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |