SNOSDJ3 May   2024 TLV1812-EP

ADVANCE INFORMATION  

  1.   1
  2. 1Features
  3. 2Applications
  4. 3Description
  5.   Pin Configuration and Functions
  6. 4Specifications
    1. 4.1 Absolute Maximum Ratings
    2. 4.2 ESD Ratings
    3. 4.3 Thermal Information - EP
    4. 4.4 Recommended Operating Conditions
    5. 4.5 Electrical Characteristics
    6. 4.6 Switching Characteristics
    7. 4.7 Typical Characteristics
  7. 5Detailed Description
    1. 5.1 Overview
    2. 5.2 Functional Block Diagrams
    3. 5.3 Feature Description
    4. 5.4 Device Functional Modes
      1. 5.4.1 Inputs
        1. 5.4.1.1 TLV18x2-EP Rail-to-Rail Input
        2. 5.4.1.2 ESD Protection
        3. 5.4.1.3 Unused Inputs
      2. 5.4.2 Outputs
        1. 5.4.2.1 TLV1812-EP Push-Pull Output
        2. 5.4.2.2 TLV1822-EP Open-Drain Output
      3. 5.4.3 Power-On Reset (POR)
      4. 5.4.4 Hysteresis
  8. 6Application and Implementation
    1. 6.1 Application Information
      1. 6.1.1 Basic Comparator Definitions
        1. 6.1.1.1 Operation
        2. 6.1.1.2 Propagation Delay
        3. 6.1.1.3 Overdrive Voltage
      2. 6.1.2 Hysteresis
        1. 6.1.2.1 Inverting Comparator With Hysteresis
        2. 6.1.2.2 Non-Inverting Comparator With Hysteresis
        3. 6.1.2.3 Inverting and Non-Inverting Hysteresis using Open-Drain Output
    2. 6.2 Typical Applications
      1. 6.2.1 Window Comparator
        1. 6.2.1.1 Design Requirements
        2. 6.2.1.2 Detailed Design Procedure
        3. 6.2.1.3 Application Curve
      2. 6.2.2 Square-Wave Oscillator
        1. 6.2.2.1 Design Requirements
        2. 6.2.2.2 Detailed Design Procedure
        3. 6.2.2.3 Application Curve
      3. 6.2.3 Adjustable Pulse Width Generator
      4. 6.2.4 Time Delay Generator
      5. 6.2.5 Logic Level Shifter
      6. 6.2.6 One-Shot Multivibrator
      7. 6.2.7 Bi-Stable Multivibrator
      8. 6.2.8 Zero Crossing Detector
      9. 6.2.9 Pulse Slicer
    3. 6.3 Power Supply Recommendations
    4. 6.4 Layout
      1. 6.4.1 Layout Guidelines
      2. 6.4.2 Layout Example
  9. 7Device and Documentation Support
    1. 7.1 Documentation Support
      1. 7.1.1 Related Documentation
    2. 7.2 Receiving Notification of Documentation Updates
    3. 7.3 Support Resources
    4. 7.4 Trademarks
    5. 7.5 Electrostatic Discharge Caution
    6. 7.6 Glossary
  10. 8Revision History
  11. 9Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.2.1.2 Detailed Design Procedure

Configure the circuit as shown in Figure 6-7. Connect VCC to a 3.3V power supply and VEE to ground. Make R1, R2 and R3 each 10MΩ resistors. These three resistors are used to create the positive and negative thresholds for the window comparator (VTH+ and VTH–).

With each resistor being equal, VTH+ is 2.2V and VTH- is 1.1V. Large resistor values such as 10MΩ are used to minimize power consumption. The resistor values can be recalculated to provide the desired trip point values.

The sensor output voltage is applied to the inverting and noninverting inputs of the two comparators. Using two open-drain output comparators allows the two comparator outputs to be Wire-OR'ed together.

The respective comparator outputs will be low when the sensor is less than 1.1V or greater than 2.2V. The respective comparator outputs will be high when the sensor is in the range of 1.1V to 2.2V (within the "window"), as shown in Figure 6-8.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |