SLAS663C August   2009  – June 2016 TLV320AIC3106-Q1

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (Continued)
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Thermal Information
    5. 8.5  Electrical Characteristics
    6. 8.6  Switching Characteristics I2S/LJF/RJF In Master Mode
    7. 8.7  Switching Characteristics I2S/LJF/RJF In Slave Mode
    8. 8.8  Switching Characteristics DSP In Master Mode
    9. 8.9  Switching Characteristics DSP In Slave Mode
    10. 8.10 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Audio Data Converters
      2. 9.3.2  Stereo Audio ADC
        1. 9.3.2.1 Stereo Audio ADC High-Pass Filter
      3. 9.3.3  Automatic Gain Control (AGC)
      4. 9.3.4  Stereo Audio DAC
      5. 9.3.5  Digital Audio Processing For Playback
      6. 9.3.6  Digital Interpolation Filter
      7. 9.3.7  Delta-Sigma Audio Dac
      8. 9.3.8  Audio Dac Digital Volume Control
      9. 9.3.9  Analog Output Common-Mode Adjustment
      10. 9.3.10 Audio DAC Power Control
      11. 9.3.11 Audio Analog Inputs
      12. 9.3.12 Analog Input Bypass Path Functionality
      13. 9.3.13 ADC PGA Signal Bypass Path Functionality
      14. 9.3.14 Input Impedance and VCM Control
      15. 9.3.15 MICBIAS Generation
      16. 9.3.16 Analog Fully Differential Line Output Drivers
      17. 9.3.17 Analog High Power Output Drivers
      18. 9.3.18 Short Circuit Output Protection
      19. 9.3.19 Jack and Headset Detection
      20. 9.3.20 General-Purpose I/O
    4. 9.4 Device Functional Modes
      1. 9.4.1 Digital Audio Processing For Record Path
      2. 9.4.2 Increasing DAC Dynamic Range
      3. 9.4.3 Passive Analog Bypass During Powerdown
      4. 9.4.4 Digital Microphone Connectivity
    5. 9.5 Programming
      1. 9.5.1  Hardware Reset
      2. 9.5.2  Digital Control Serial Interface
        1. 9.5.2.1 SPI Control Mode
        2. 9.5.2.2 SPI Communication Protocol
          1. 9.5.2.2.1 Limitation On Register Writing
        3. 9.5.2.3 Continuous Read and Write Operation
      3. 9.5.3  I2C Control Mode
      4. 9.5.4  I2C Bus Debug In A Glitched System
      5. 9.5.5  Digital Audio Data Serial Interface
      6. 9.5.6  Right-Justified Mode
      7. 9.5.7  Left-Justified Mode
      8. 9.5.8  I2S Mode
      9. 9.5.9  DSP Mode
      10. 9.5.10 TDM Data Transfer
      11. 9.5.11 Audio Clock Generation
    6. 9.6 Register Maps
      1. 9.6.1 Output Stage Volume Controls
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Receiving Notification of Documentation Updates
    2. 13.2 Community Resources
    3. 13.3 Trademarks
    4. 13.4 Electrostatic Discharge Caution
    5. 13.5 Glossary
  14. 14Mechanical, Packaging, And Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8 Specifications

8.1 Absolute Maximum Ratings

see (1)
MIN MAX UNIT
AVDD_DAC to AVSS_DAC, DRVDD to DRVSS, AVSS_ADC –0.3 3.9 V
AVDD to DRVSS –0.3 3.9 V
IOVDD to DVSS –0.3 3.9 V
DVDD to DVSS –0.3 2.5 V
AVDD_DAC to DRVDD –0.1 0.1 V
Digital input voltage to DVSS –0.3 VIOVDD + 0.3 V
Analog input voltage to AVSS_ADC –0.3 VAVDD + 0.3 V
Power dissipation (TJ(MAX) – TA) / θJA
Operating temperature range –40 85 °C
Junction temperature, TJ 105 °C
Storage temperature, Tstg –65 105 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

8.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per AEC Q100-002(1) ±1500 V
Charged-device model (CDM), per AEC Q100-011 ±1000
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.

8.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNIT
VAVDD_DAC, VDRVDD Analog supply voltage(1) 2.7 3.3 3.6 V
VDVDD Digital core supply voltage(1) 1.65 1.8 1.95 V
VIOVDD Digital I/O supply voltage(1) 1.1 1.8 3.6 V
VI Analog, full-scale, 0-dB input voltage (DRVDD1 = 3.3 V) 0.707 VRMS
Stereo line output load resistance 10 kΩ
Stereo headphone output load resistance 16 Ω
Digital output load capacitance 10 pF
TA Operating free-air temperature –40 85 °C
(1) Analog voltage values are with respect to AVSS_ADC, AVSS_DAC, DRVSS; digital voltage values are with respect to DVSS.

8.4 Thermal Information

THERMAL METRIC(1) TLV320AIC3106-Q1 UNIT
RGZ (VQFN)
48 PINS
RθJA Junction-to-ambient thermal resistance 30.7 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 13.4 °C/W
RθJB Junction-to-board thermal resistance 7.2 °C/W
ψJT Junction-to-top characterization parameter 0.2 °C/W
ψJB Junction-to-board characterization parameter 7.2 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance 1.5 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.

8.5 Electrical Characteristics

TA = –40°C to 85°C, VAVDD_DAC, VDRVDD, VIOVDD = 3.3 V, VDVDD = 1.8 V, fS = 48-kHz, 16-bit audio data
(unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
AUDIO ADC
Input signal level (0 dB) Single-ended input 0.707 VRMS
Signal-to-noise ratio, A-weighted(1)(2) fS = 48 ksps, 0-dB PGA gain, inputs AC-shorted to ground 80 92 dB
Dynamic range(2) fS = 48 ksps, 0-dB PGA gain, –60-dB full-scale input signal 91 dB
THD Total harmonic distortion fS = 48 ksps, 0-dB PGA gain, –2-dB full-scale,
1-kHz input signal		 –88 –70 dB
PSRR Power supply rejection ratio 217-Hz signal applied to DRVDD 49 dB
1-kHz signal applied to DRVDD 46
Gain error fS = 48 ksps, 0-dB PGA gain, –2-dB full-scale,
1-kHz input signal		 0.84 dB
Input channel separation 1-kHz, –2-dB full-scale signal, MIC3L to MIC3R –86 dB
1-kHz, –2-dB full-scale signal, MIC2L to MIC2R –98
1-kHz, –2-dB full-scale signal, MIC1L to MIC1R –75
ADC programmable gain amplifier maximum gain 1-kHz input tone 59.5 dB
ADC programmable gain amplifier step size 0.5 dB
Input resistance MIC1L and MIC1R inputs routed to single ADC,
Input mix attenuation = 0 dB		 20 kΩ
MIC1L and MIC1R inputs routed to single ADC,
input mix attenuation = 12 dB		 80
MIC2L and MIC2R inputs routed to single ADC,
Input mix attenuation = 0 dB		 20
MIC2L and MIC2R inputs routed to single ADC,
input mix attenuation = 12 dB		 80
MIC3L and MIC3R inputs routed to single ADC,
Input mix attenuation = 0 dB		 20
MIC3L and MIC3R inputs routed to single ADC,
input mix attenuation = 12 dB		 80
Input level control minimum attenuation setting 0 dB
Input level control maximum attenuation setting 12 dB
Input signal level Differential Input 1.414 VRMS
Signal-to-noise ratio, A-weighted(1)(2) fS = 48 ksps, 0-dB PGA gain, inputs AC-shorted to ground, differential mode 92 dB
THD Total harmonic distortion fS = 48 ksps, 0-dB PGA gain,
–2-dB full-scale 1-kHz input signal, differential mode		 –91 dB
ANALOG PASS THROUGH MODE
Input to output switch resistance, (rDS(ON)) MIC1/LINE1 to LINE_OUT 330 Ω
MIC2/LINE2 to LINE_OUT 330
ADC DIGITAL DECIMATION FILTER, fS = 48 kHz
Filter gain from 0 to 0.39 fS ±0.1 dB
Filter gain at 0.4125 fS –0.25 dB
Filter gain at 0.45 fS –3 dB
Filter gain at 0.5 fS –17.5 dB
Filter gain from 0.55 fS to 64 fS –75 dB
Filter group delay 17 / fS s
MICROPHONE BIAS
Bias voltage Programmable setting = 2 2 V
Programmable setting = 2.5 2.3 2.5 2.7
Programmable setting = VDRVDD VDRVDD
Current sourcing Programmable setting = 2.5 V 4 mA
AUDIO DAC: DIFFERENTIAL LINE OUTPUT, LOAD = 10 kΩ
Full-scale output voltage 0-dB input full-scale signal, output volume control = 0 dB, output common-mode setting = 1.35 V 1.414 VRMS
SNR Signal-to-noise ratio, A-weighted(3) No input signal, output volume control = 0 dB,
output common mode setting = 1.35 V, fS = 48 kHz		 90 102 dB
Dynamic range, A-weighted –60-dB, 1-kHz input full-scale signal,
output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz		 99 dB
THD Total harmonic distortion 0-dB, 1-kHz input full-scale signal,
output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz		 –94 –75 dB
Power-supply rejection ratio 217-Hz signal applied to DRVDD, AVDD_DAC 77 dB
1-kHz signal applied to DRVDD, AVDD_DAC 73
DAC channel separation 0-dB full-scale input signal between left and right line out 123 dB
DAC gain error 0-dB, 1-kHz input full-scale signal,
output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz		 –0.4 dB
AUDIO DAC: SINGLE ENDED LINE OUTPUT, LOAD = 10 kΩ
Full-scale output voltage 0-dB input full-scale signal, output volume control = 0 dB, output common-mode setting = 1.35 V 0.707 Vrms
SNR Signal-to-noise ratio, A-weighted No input signal, output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz		 97 dB
THD Total harmonic distortion 0-dB, 1-kHz input full-scale signal,
output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz		 84 dB
DAC gain error 0-dB, 1-kHz input full-scale signal,
output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz		 0.55 dB
AUDIO DAC: SINGLE ENDED HEADPHONE OUTPUT, LOAD = 16 Ω
Full-scale output voltage 0-dB input full-scale signal, output volume control = 0 dB, output common-mode setting = 1.35 V 0.707 Vrms
SNR Signal-to-noise ratio, A-weighted No input signal, output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz		 95 dB
No input signal, output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz,
50% DAC current boost mode		 96 dB
Dynamic range, A-weighted –60-dB, 1-kHz input full-scale signal,
output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz		 92 dB
THD Total harmonic distortion 0-dB, 1-kHz input full-scale signal,
output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz, 25°C		 –80 –65 dB
PSRR Power-supply rejection ratio 217-Hz signal applied to DRVDD, AVDD_DAC 41 dB
1-kHz signal applied to DRVDD, AVDD_DAC 44
DAC channel separation 0-dB full-scale input signal between left and right line out 84 dB
DAC gain error 0-dB, 1-kHz input full-scale signal,
output volume control = 0 dB,
output common-mode setting = 1.35 V, fS = 48 kHz		 –0.5 dB
AUDIO DAC: LINEOUT AND HEADPHONE OUT DRIVERS
Output common mode First option 1.35 V
Second option 1.5
Third option 1.65
Fourth option 1.8
Output volume control maximum setting 9 dB
Output volume control step size 1 dB
DAC DIGITAL INTERPOLATION(5): FILTER fS = 48 ksps, 25°C
Pass band 0 0.45 fS Hz
Pass-band ripple ±0.06 dB
Transition band 0.45 fS 0.55 fS Hz
Stop band 0.55 fS 7.5 fS Hz
Stop-band attenuation 65 dB
Group delay 21 / fS s
DIGITAL I/O, 25°C
VIL Input low level –0.3 0.3 × VIOVDD V
VIH Input high level(4) VIOVDD > 1.6 V 0.7 × VIOVDD V
VIOVDD < 1.6 V 1.1
VOL Output low level 0.1 × VIOVDD V
VOH Output high level 0.8 × VIOVDD V
POWER CONSUMPTION, DRVDD, AVDD_DAC = 3.3 V, DVDD = 1.8 V, IOVDD = 3.3 V
IDRVDD + IAVDD_DAC RESET held low 0.1 μA
IDVDD 0.2
IDRVDD + IAVDD_DAC Mono ADC record, fS = 8 ksps, I2S slave,
AGC off, no signal		 2.1 mA
IDVDD 0.5
IDRVDD + IAVDD_DAC Stereo ADC record, fS = 8 ksps, I2S slave,
AGC off, no signal		 4.1 mA
IDVDD 0.6
IDRVDD + IAVDD_DAC Stereo ADC record, fS = 48 ksps, I2S slave,
AGC off, no signal		 4.3 mA
IDVDD 2.5
IDRVDD + IAVDD_DAC Stereo DAC playback to line out, analog mixer bypassed,
fS = 48 ksps, I2S slave		 3.5 mA
IDVDD 2.3
IDRVDD + IAVDD_DAC Stereo DAC playback to line out, fS = 48 ksps, I2S slave, no signal 4.9 mA
IDVDD 2.3
IDRVDD + IAVDD_DAC Stereo DAC playback to stereo single-ended headphone,
fS = 48 ksps, I2S slave, no signal		 6.7 mA
IDVDD 2.3
IDRVDD + IAVDD_DAC Stereo line in to stereo line out, no signal 3.1 mA
IDVDD 0
IDRVDD + IAVDD_DAC Extra power when PLL enabled 1.4 mA
IDVDD 0.9
IDRVDD + IAVDD_DAC All blocks powered down, headset detection enabled 28 μA
IDVDD 2
(1) Ratio of output level with 1-kHz full-scale sine-wave input, to the output level with the inputs short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer.
(2) All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values.
(3) Unless otherwise noted, all measurements use output common-mode voltage setting of 1.35 V, 0-dB output level control gain, 16-Ω single-ended load.
(4) When VIOVDD < 1.6 V, minimum VIH is 1.1 V.
(5) Not production tested. Specified by design.

8.6 Switching Characteristics I2S/LJF/RJF In Master Mode

All specifications at 25°C, DVDD = 1.8 V.
PARAMETER MIN MAX UNIT
td(WS) ADWS/WCLK delay time VIOVDD = 1.1 V 50 ns
VIOVDD = 3.3 V 15
td(DO-WS) ADWS/WCLK to DOUT delay time VIOVDD = 1.1 V 50 ns
VIOVDD = 3.3 V 20
td(DO-BCLK) BCLK to DOUT delay time VIOVDD = 1.1 V 50 ns
VIOVDD = 3.3 V 15
ts(DI) DIN setup time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
th(DI) DIN hold time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
tr Rise time VIOVDD = 1.1 V 30 ns
VIOVDD = 3.3 V 10
tf Fall time VIOVDD = 1.1 V 30 ns
VIOVDD = 3.3 V 10

8.7 Switching Characteristics I2S/LJF/RJF In Slave Mode

All specifications at 25°C, DVDD = 1.8 V.
PARAMETER MIN MAX UNIT
tH(BCLK) BCLK high period VIOVDD = 1.1 V 70 ns
VIOVDD = 3.3 V 35
tL(BCLK) BCLK low period VIOVDD = 1.1 V 70 ns
VIOVDD = 3.3 V 35
ts(WS) ADWS/WCLK setup time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
th(WS) ADWS/WCLK hold time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
td(DO-WS) ADWS/WCLK to DOUT delay time (for LJF Mode only) VIOVDD = 1.1 V 50 ns
VIOVDD = 3.3 V 35
td(DO-BCLK) BCLK to DOUT delay time VIOVDD = 1.1 V 50 ns
VIOVDD = 3.3 V 20
ts(DI) DIN setup time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
th(DI) DIN hold time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
tr Rise time VIOVDD = 1.1 V 8 ns
VIOVDD = 3.3 V 4
tf Fall time VIOVDD = 1.1 V 8 ns
VIOVDD = 3.3 V 4

8.8 Switching Characteristics DSP In Master Mode

All specifications at 25°C, DVDD = 1.8 V.
PARAMETER MIN MAX UNIT
td(WS) ADWS/WCLK delay time VIOVDD = 1.1 V 50 ns
VIOVDD = 3.3 V 15
td(DO-BCLK) BCLK to DOUT delay time VIOVDD = 1.1 V 50 ns
VIOVDD = 3.3 V 15
ts(DI) DIN setup time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
th(DI) DIN hold time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
tr Rise time VIOVDD = 1.1 V 30 ns
VIOVDD = 3.3 V 10
tf Fall time VIOVDD = 1.1 V 30 ns
VIOVDD = 3.3 V 10

8.9 Switching Characteristics DSP In Slave Mode

All specifications at 25°C, DVDD = 1.8 V.
PARAMETER MIN MAX UNIT
tH(BCLK) BCLK high period VIOVDD = 1.1 V 70 ns
VIOVDD = 3.3 V 35
tL(BCLK) BCLK low period VIOVDD = 1.1 V 70 ns
VIOVDD = 3.3 V 35
ts(WS) ADWS/WCLK setup time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 8
th(WS) ADWS/WCLK hold time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 8
td(DO-BCLK) BCLK to DOUT delay time VIOVDD = 1.1 V 50 ns
VIOVDD = 3.3 V 20
ts(DI) DIN setup time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
th(DI) DIN hold time VIOVDD = 1.1 V 10 ns
VIOVDD = 3.3 V 6
tr Rise time VIOVDD = 1.1 V 8 ns
VIOVDD = 3.3 V 4
tf Fall time VIOVDD = 1.1 V 8 ns
VIOVDD = 3.3 V 4
TLV320AIC3106-Q1 t0145-01_las663.gif Figure 1. I2S/LJF/RJF Timing In Master Mode
TLV320AIC3106-Q1 t0145-02_las663.gif Figure 2. I2S/LJF/RJF Timing In Slave Mode
TLV320AIC3106-Q1 t0146-01_las663.gif Figure 3. DSP Timing In Master Mode
TLV320AIC3106-Q1 t0146-02_las663.gif Figure 4. DSP Timing In Slave Mode

8.10 Typical Characteristics

TLV320AIC3106-Q1 thd1_op_las663.gif Figure 5. Total Harmonic Distortion vs
Headphone Out Power
TLV320AIC3106-Q1 mbias_v_las663.gif Figure 7. MICBIAS Voltage vs Supply Voltage
TLV320AIC3106-Q1 l_dac_fft_las663.gif Figure 9. Left DAC FFT
TLV320AIC3106-Q1 l_adc_fft_las663.gif Figure 11. Left ADC FFT
TLV320AIC3106-Q1 snr_adc_las663.gif Figure 6. Signal-To-Noise Ratio vs ADC PGA Setting
TLV320AIC3106-Q1 mbias_ta_las663.gif Figure 8. MICBIAS Voltage vs Free-Air Temperature
TLV320AIC3106-Q1 r_dac_fft_las663.gif Figure 10. Right DAC FFT
TLV320AIC3106-Q1 r_adc_fft_las663.gif Figure 12. Right ADC FFT
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |