ZHCSGV6F June   2009  – January 2017 TMS320C6742

PRODUCTION DATA.  

  1. 1器件概述
    1. 1.1 特性
    2. 1.2 应用
    3. 1.3 说明
    4. 1.4 功能方框图
  2. 2Revision History
  3. 3Device Comparison
    1. 3.1 Device Characteristics
    2. 3.2 Device Compatibility
    3. 3.3 DSP Subsystem
      1. 3.3.1 C674x DSP CPU Description
      2. 3.3.2 DSP Memory Mapping
        1. 3.3.2.1 External Memories
        2. 3.3.2.2 DSP Internal Memories
        3. 3.3.2.3 C674x CPU
    4. 3.4 Memory Map Summary
      1. Table 3-4 C6742 Top Level Memory Map
    5. 3.5 Pin Assignments
      1. 3.5.1 Pin Map (Bottom View)
    6. 3.6 Pin Multiplexing Control
    7. 3.7 Terminal Functions
      1. 3.7.1  Device Reset, NMI and JTAG
      2. 3.7.2  High-Frequency Oscillator and PLL
      3. 3.7.3  Real-Time Clock and 32-kHz Oscillator
      4. 3.7.4  DEEPSLEEP Power Control
      5. 3.7.5  External Memory Interface A (EMIFA)
      6. 3.7.6  DDR2/mDDR Controller
      7. 3.7.7  Serial Peripheral Interface Modules (SPI)
      8. 3.7.8  Enhanced Capture/Auxiliary PWM Modules (eCAP0)
      9. 3.7.9  Enhanced Pulse Width Modulators (eHRPWM)
      10. 3.7.10 Boot
      11. 3.7.11 Universal Asynchronous Receiver/Transmitters (UART0)
      12. 3.7.12 Inter-Integrated Circuit Modules(I2C0)
      13. 3.7.13 Timers
      14. 3.7.14 Multichannel Audio Serial Ports (McASP)
      15. 3.7.15 Multichannel Buffered Serial Ports (McBSP)
      16. 3.7.16 Universal Host-Port Interface (UHPI)
      17. 3.7.17 General Purpose Input Output
      18. 3.7.18 Reserved and No Connect
      19. 3.7.19 Supply and Ground
    8. 3.8 Unused Pin Configurations
  4. 4Device Configuration
    1. 4.1 Boot Modes
    2. 4.2 SYSCFG Module
    3. 4.3 Pullup/Pulldown Resistors
  5. 5Specifications
    1. 5.1 Absolute Maximum Ratings Over Operating Junction Temperature Range (Unless Otherwise Noted)
    2. 5.2 Handling Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Notes on Recommended Power-On Hours (POH)
    5. 5.5 Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Junction Temperature (Unless Otherwise Noted)
  6. 6Peripheral Information and Electrical Specifications
    1. 6.1  Parameter Information
      1. 6.1.1 Parameter Information Device-Specific Information
        1. 6.1.1.1 Signal Transition Levels
    2. 6.2  Recommended Clock and Control Signal Transition Behavior
    3. 6.3  Power Supplies
      1. 6.3.1 Power-On Sequence
      2. 6.3.2 Power-Off Sequence
    4. 6.4  Reset
      1. 6.4.1 Power-On Reset (POR)
      2. 6.4.2 Warm Reset
      3. 6.4.3 Reset Electrical Data Timings
    5. 6.5  Crystal Oscillator or External Clock Input
    6. 6.6  Clock PLLs
      1. 6.6.1 PLL Device-Specific Information
      2. 6.6.2 Device Clock Generation
      3. 6.6.3 Dynamic Voltage and Frequency Scaling (DVFS)
    7. 6.7  Interrupts
      1. 6.7.1 DSP Interrupts
    8. 6.8  Power and Sleep Controller (PSC)
      1. 6.8.1 Power Domain and Module Topology
        1. 6.8.1.1 Power Domain States
        2. 6.8.1.2 Module States
    9. 6.9  Enhanced Direct Memory Access Controller (EDMA3)
      1. 6.9.1 EDMA3 Channel Synchronization Events
      2. 6.9.2 EDMA3 Peripheral Register Descriptions
    10. 6.10 External Memory Interface A (EMIFA)
      1. 6.10.1 EMIFA Asynchronous Memory Support
      2. 6.10.2 EMIFA Synchronous DRAM Memory Support
      3. 6.10.3 EMIFA SDRAM Loading Limitations
      4. 6.10.4 EMIFA Connection Examples
      5. 6.10.5 External Memory Interface Register Descriptions
      6. 6.10.6 EMIFA Electrical Data/Timing
        1. Table 6-19 Timing Requirements for EMIFA SDRAM Interface
        2. Table 6-20 Switching Characteristics for EMIFA SDRAM Interface
        3. Table 6-21 Timing Requirements for EMIFA Asynchronous Memory Interface
    11. 6.11 DDR2/mDDR Memory Controller
      1. 6.11.1 DDR2/mDDR Memory Controller Electrical Data/Timing
      2. 6.11.2 DDR2/mDDR Memory Controller Register Description(s)
      3. 6.11.3 DDR2/mDDR Interface
        1. 6.11.3.1  DDR2/mDDR Interface Schematic
        2. 6.11.3.2  Compatible JEDEC DDR2/mDDR Devices
        3. 6.11.3.3  PCB Stackup
        4. 6.11.3.4  Placement
        5. 6.11.3.5  DDR2/mDDR Keep Out Region
        6. 6.11.3.6  Bulk Bypass Capacitors
        7. 6.11.3.7  High-Speed Bypass Capacitors
        8. 6.11.3.8  Net Classes
        9. 6.11.3.9  DDR2/mDDR Signal Termination
        10. 6.11.3.10 VREF Routing
        11. 6.11.3.11 DDR2/mDDR CK and ADDR_CTRL Routing
        12. 6.11.3.12 DDR2/mDDR Boundary Scan Limitations
    12. 6.12 Memory Protection Units
    13. 6.13 Multichannel Audio Serial Port (McASP)
      1. 6.13.1 McASP Peripheral Registers Description(s)
      2. 6.13.2 McASP Electrical Data/Timing
        1. 6.13.2.1 Multichannel Audio Serial Port 0 (McASP0) Timing
          1. Table 6-42 Timing Requirements for McASP0 (1.2V, 1.1V)
          2. Table 6-43 Timing Requirements for McASP0 (1.0V)
          3. Table 6-44 Switching Characteristics for McASP0 (1.2V, 1.1V)
          4. Table 6-45 Switching Characteristics for McASP0 (1.0V)
    14. 6.14 Multichannel Buffered Serial Port (McBSP)
      1. 6.14.1 McBSP Peripheral Register Description(s)
      2. 6.14.2 McBSP Electrical Data/Timing
        1. 6.14.2.1 Multichannel Buffered Serial Port (McBSP) Timing
          1. Table 6-47 Timing Requirements for McBSP1 [1.2V, 1.1V] (see )
          2. Table 6-48 Timing Requirements for McBSP1 [1.0V] (see )
          3. Table 6-49 Switching Characteristics for McBSP1 [1.2V, 1.1V] (see )
          4. Table 6-50 Switching Characteristics for McBSP1 [1.0V] (see )
          5. Table 6-51 Timing Requirements for McBSP1 FSR When GSYNC = 1 (see )
    15. 6.15 Serial Peripheral Interface Ports (SPI1)
      1. 6.15.1 SPI Peripheral Registers Description(s)
      2. 6.15.2 SPI Electrical Data/Timing
        1. 6.15.2.1 Serial Peripheral Interface (SPI) Timing
          1. Table 6-53 General Timing Requirements for SPI1 Master Modes
          2. Table 6-54 General Timing Requirements for SPI1 Slave Modes
          3. Table 6-55 Additional SPI1 Master Timings, 4-Pin Enable Option
          4. Table 6-56 Additional SPI1 Master Timings, 4-Pin Chip Select Option
    16. 6.16 Inter-Integrated Circuit Serial Ports (I2C)
      1. 6.16.1 I2C Device-Specific Information
      2. 6.16.2 I2C Peripheral Registers Description(s)
      3. 6.16.3 I2C Electrical Data/Timing
        1. 6.16.3.1 Inter-Integrated Circuit (I2C) Timing
          1. Table 6-62 Timing Requirements for I2C Input
          2. Table 6-63 Switching Characteristics for I2C
    17. 6.17 Universal Asynchronous Receiver/Transmitter (UART)
      1. 6.17.1 UART Peripheral Registers Description(s)
      2. 6.17.2 UART Electrical Data/Timing
        1. Table 6-65 Timing Requirements for UART Receive (see )
        2. Table 6-66 Switching Characteristics Over Recommended Operating Conditions for UARTx Transmit (see )
    18. 6.18 Host-Port Interface (UHPI)
      1. 6.18.1 HPI Device-Specific Information
      2. 6.18.2 HPI Peripheral Register Description(s)
      3. 6.18.3 HPI Electrical Data/Timing
        1. Table 6-68 Timing Requirements for Host-Port Interface [1.2V, 1.1V]
        2. Table 6-69 Switching Characteristics Over Recommended Operating Conditions for Host-Port Interface [1.2V, 1.1V]
        3. Table 6-70 Switching Characteristics Over Recommended Operating Conditions for Host-Port Interface [1.0V]
    19. 6.19 Enhanced Capture (eCAP) Peripheral
      1. Table 6-72 Timing Requirements for Enhanced Capture (eCAP)
      2. Table 6-73 Switching Characteristics Over Recommended Operating Conditions for eCAP
    20. 6.20 Enhanced High-Resolution Pulse-Width Modulator (eHRPWM)
      1. 6.20.1 Enhanced Pulse Width Modulator (eHRPWM) Timing
        1. Table 6-75 Timing Requirements for eHRPWM
        2. Table 6-76 Switching Characteristics Over Recommended Operating Conditions for eHRPWM
      2. 6.20.2 Trip-Zone Input Timing
    21. 6.21 Timers
      1. 6.21.1 Timer Electrical Data/Timing
        1. Table 6-79 Timing Requirements for Timer Input (see )
        2. Table 6-80 Switching Characteristics Over Recommended Operating Conditions for Timer Output
    22. 6.22 Real Time Clock (RTC)
      1. 6.22.1 Clock Source
      2. 6.22.2 Real-Time Clock Register Descriptions
    23. 6.23 General-Purpose Input/Output (GPIO)
      1. 6.23.1 GPIO Register Description(s)
      2. 6.23.2 GPIO Peripheral Input/Output Electrical Data/Timing
        1. Table 6-83 Timing Requirements for GPIO Inputs (see )
        2. Table 6-84 Switching Characteristics Over Recommended Operating Conditions for GPIO Outputs (see )
      3. 6.23.3 GPIO Peripheral External Interrupts Electrical Data/Timing
        1. Table 6-85 Timing Requirements for External Interrupts (see )
    24. 6.24 Emulation Logic
      1. 6.24.1 JTAG Port Description
      2. 6.24.2 Scan Chain Configuration Parameters
      3. 6.24.3 Initial Scan Chain Configuration
      4. 6.24.4 IEEE 1149.1 JTAG
        1. 6.24.4.1 JTAG Peripheral Register Description(s) – JTAG ID Register (DEVIDR0)
        2. 6.24.4.2 JTAG Test-Port Electrical Data/Timing
          1. Table 6-91 Timing Requirements for JTAG Test Port (see )
          2. Table 6-92 Switching Characteristics Over Recommended Operating Conditions for JTAG Test Port (see )
      5. 6.24.5 JTAG 1149.1 Boundary Scan Considerations
  7. 7Device and Documentation Support
    1. 7.1 Device Nomenclature
    2. 7.2 Tools and Software
    3. 7.3 Documentation Support
    4. 7.4 社区资源
    5. 7.5 商标
    6. 7.6 静电放电警告
    7. 7.7 出口管制提示
    8. 7.8 术语表
  8. 8Mechanical Packaging and Orderable Information
    1. 8.1 Thermal Data for ZCE Package
    2. 8.2 Thermal Data for ZWT Package
    3. 8.3 Packaging Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • ZWT|361
散热焊盘机械数据 (封装 | 引脚)
订购信息

5.3 Recommended Operating Conditions

NAME DESCRIPTION CONDITION MIN NOM MAX UNIT
Supply
Voltage		 CVDD Core Logic Supply Voltage (variable) 1.2V operating point 1.14 1.2 1.32 V
1.1V operating point 1.05 1.1 1.16 V
1.0V operating point 0.95 1.0 1.05 V
RVDD Internal RAM Supply Voltage 1.14 1.2 1.32 V
RTC_CVDD(4) RTC Core Logic Supply Voltage 0.9 1.2 1.32 V
PLL0_VDDA PLL0 Supply Voltage 1.14 1.2 1.32 V
PLL1_VDDA PLL1 Supply Voltage 1.14 1.2 1.32 V
DVDD18(5) 1.8V Supply Voltage 1.71 1.8 1.89 V
DDR_DVDD18 (5) DDR2 PHY Supply Voltage 1.71 1.8 1.89 V
DDR_VREF DDR2/mDDR reference voltage 0.49*
DDR_DVDD18		 0.5*
DDR_DVDD18		 0.51*
DDR_DVDD18		 V
DDR_ZP DDR2/mDDR impedance control,
connected via 50Ω resistor to Vss		 Vss V
DVDD3318_A Power Group A Dual-voltage IO Supply Voltage 1.8V operating point 1.71 1.8 1.89 V
3.3V operating point 3.15 3.3 3.45 V
DVDD3318_B Power Group B Dual-voltage IO Supply Voltage 1.8V operating point 1.71 1.8 1.89 V
3.3V operating point 3.15 3.3 3.45 V
DVDD3318_C Power Group C Dual-voltage IO Supply Voltage 1.8V operating point 1.71 1.8 1.89 V
3.3V operating point 3.15 3.3 3.45 V
Supply
Ground		 VSS Core Logic Digital Ground 0 0 0 V
PLL0_VSSA PLL0 Ground
PLL1_VSSA PLL1 Ground
OSCVSS(1) Oscillator Ground
RTC_VSS(1) RTC Oscillator Ground
Voltage
Input High		 VIH High-level input voltage, Dual-voltage I/O, 3.3V(2) 2 V
High-level input voltage, Dual-voltage I/O, 1.8V (2) 0.65*DVDD V
High-level input voltage, RTC_XI 0.8*RTC_CVDD V
High-level input voltage, OSCIN 0.8*CVDD V
Voltage
Input Low		 VIL Low-level input voltage, Dual-voltage I/O, 3.3V(2) 0.8 V
Low-level input voltage, Dual-voltage I/O, 1.8V (2) 0.35*DVDD V
Low-level input voltage, RTC_XI 0.2*RTC_CVDD V
Low-level input voltage, OSCIN 0.2*CVDD V
Transition Time tt Transition time, 10%-90%, All Inputs (unless otherwise specified in the electrical data sections) 0.25P or 10 (3) ns
Operating
Frequency		 FPLL0_SYSCLK1,6 Commercial temperature grade (default) CVDD = 1.2V operating point 0 200 MHz
CVDD = 1.1V operating point 0 150
CVDD = 1.0V operating point 0 100
Extended temperature grade (A suffix) CVDD = 1.2V operating point 0 200 MHz
CVDD = 1.1V operating point 0 150
CVDD = 1.0V operating point 0 100
(1) When an external crystal is used oscillator (OSC_VSS, RTC_VSS) ground must be kept separate from other grounds and connected directly to the crystal load capacitor ground. These pins are shorted to VSS on the device itself and should not be connected to VSS on the circuit board. If a crystal is not used and the clock input is driven directly, then the oscillator VSS may be connected to board ground.
(2) These IO specifications apply to the dual-voltage IOs only and do not apply to DDR2/mDDR . DDR2/mDDR IOs are 1.8V IOs and adhere to the JESD79-2A standard.
(3) Whichever is smaller. P = the period of the applied signal. Maintaining transition times as fast as possible is recommended to improve noise immunity on input signals.
(4) The RTC provides an option for isolating the RTC_CVDD from the CVDD to reduce current leakage when the RTC is powered independently. If these power supplies are not isolated (CTRL.SPLITPOWER=0), RTC_CVDD must be equal to or greater than CVDD. If these power supplies are isolated (CTRL.SPLITPOWER=1), RTC_CVDD may be lower than CVDD.
(5) DVDD18 must be powered even if all of the DVDD3318_x x supplies are operated at 3.3V.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |