ZHCSF52B June   2016  – December 2017 TPA3137D2

PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
    1.     Device Images
      1.      简化原理图
  4. 修订历史记录
  5. Device Comparison Table
  6. Pin Configuration and Functions
    1.     Pin Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Switching Characteristics
    7. 7.7 Typical Characteristics
  8. Parameter Measurement Information
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Fixed Analog Gain
      2. 9.3.2 SD Operation
      3. 9.3.3 PLIMIT
      4. 9.3.4 Spread Spectrum and De-Phase Control
      5. 9.3.5 GVDD Supply
      6. 9.3.6 DC Detect
      7. 9.3.7 PBTL Select
      8. 9.3.8 Short-Circuit Protection and Automatic Recovery Feature
      9. 9.3.9 Thermal Protection
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 Design Requirements
        1. 10.2.1.1 PCB Material Recommendation
        2. 10.2.1.2 PVCC Capacitor Recommendation
        3. 10.2.1.3 Decoupling Capacitor Recommendations
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Ferrite Bead Filter Considerations
        2. 10.2.2.2 Efficiency: LC Filter Required with the Traditional Class-D Modulation Scheme
        3. 10.2.2.3 When to Use an Output Filter for EMI Suppression
        4. 10.2.2.4 Input Resistance
        5. 10.2.2.5 Input Capacitor, Ci
        6. 10.2.2.6 BSN and BSP Capacitors
        7. 10.2.2.7 Differential Inputs
        8. 10.2.2.8 Using Low-ESR Capacitors
      3. 10.2.3 Application Performance Curves
        1. 10.2.3.1 EN55013 Radiated Emissions Results
        2. 10.2.3.2 EN55022 Conducted Emissions Results
  11. 11Power Supply Recommendations
    1. 11.1 Power Supply Decoupling, CS
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13器件和文档支持
    1. 13.1 器件支持
      1. 13.1.1 Third-Party Products Disclaimer
    2. 13.2 文档支持
      1. 13.2.1 相关文档
    3. 13.3 相关链接
    4. 13.4 接收文档更新通知
    5. 13.5 社区资源
    6. 13.6 商标
    7. 13.7 静电放电警告
    8. 13.8 Glossary
  14. 14机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Electrical Characteristics

TA = 25°C, AVCC = PVCC = 12 V, RL = 6 Ω (unless otherwise noted).(1) Over operating free-air temperature range (unless otherwise noted)
PARAMETERTEST CONDITIONSMINTYPMAXUNIT
DC CHARACTERISTICS
| VOS | Class-D output offset voltage (measured differentially) VI = 0 V, Gain = 26 dB 1.5 15 mV
ICC Quiescent supply current SD = 2 V, no load, 300 ohm Ferrite Bead + 1nF Output Filter 35 40 mA
ICC(SD) Quiescent supply current in shutdown mode SD = 0.8 V, no load 40 60 µA
rDS(on) Drain-source on-state resistance IO = 500 mA, TJ = 25°C
Excluding Metal and Bond Wire Resistance
High Side 240
Low side 240
G Gain 25 26 27 dB
ton Turn-on time SD = 2 V 14 ms
tOFF Turn-off time SD = 0.8 V 2.5 µs
GVDD Gate drive supply IGVDD = 2 mA 6.4 6.9 7.4 V
tDCDET DC detect time VRINN = 3.1 V and VRINN = 2.9 V, or VRINN = 2.9 V and VRINN = 3.1 V 950 ms
AC CHARACTERISTICS
PSRR Power supply ripple rejection 200-mVPP ripple at 1 kHz,
Gain = 26 dB, Inputs ac-coupled to GND
–65 dB
PO Continuous output power THD+N = 10%, f = 1 kHz 6 W
PO Continuous output power THD+N = 10%, f = 1 kHz, PVCC = 13 V, RL = 8 Ω 6 W
PO Continuous output power, PBTL (mono) THD+N = 10%, f = 1 kHz, PVCC = 13 V, RL = 4 Ω 12 W
THD+N Total harmonic distortion + noise f = 1 kHz, PO = 5 W (half-power) 0.06%
Vn Output integrated noise 20 Hz to 22 kHz, A-weighted filter, Gain = 26 dB 91 µV
–81 dBV
Crosstalk VO = 1 Vrms, Gain = 26 dB, f = 1 kHz –75 dB
SNR Signal-to-noise ratio Maximum output at THD+N < 1%, f = 1 kHz,
Gain = 26 dB, A-weighted
102 dB
OTE Thermal trip point 150 °C
Thermal hysteresis 15 °C
Using the TPA3137D2 EVM (SLOU444), unless otherwise noted.