ZHCSPB6D July   2022  – April 2024 TPS1211-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Charge Pump and Gate Driver Output (VS, PU, PD, BST, SRC)
      2. 8.3.2 Capacitive Load Driving
        1. 8.3.2.1 FET Gate Slew Rate Control
        2. 8.3.2.2 Using Precharge FET - (with TPS12111-Q1 Only)
      3. 8.3.3 Overcurrent and Short-Circuit Protection
        1. 8.3.3.1 Overcurrent Protection with Auto-Retry
        2. 8.3.3.2 Overcurrent Protection with Latch-Off
        3. 8.3.3.3 Short-Circuit Protection
      4. 8.3.4 Analog Current Monitor Output (IMON)
      5. 8.3.5 Overvoltage (OV) and Undervoltage Protection (UVLO)
      6. 8.3.6 Remote Temperature Sensing and Protection (DIODE)
      7. 8.3.7 Output Reverse Polarity Protection
      8. 8.3.8 TPS1211x-Q1 as a Simple Gate Driver
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application: Driving Zonal Controller Loads on 12-V Line in Power Distribution Unit
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Typical Application: Reverse Polarity Protection with TPS12110-Q1
      1. 9.3.1 Design Requirements
      2. 9.3.2 External Component Selection
      3. 9.3.3 Application Curves
    4. 9.4 Power Supply Recommendations
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
      2. 9.5.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 接收文档更新通知
    2. 10.2 支持资源
    3. 10.3 Trademarks
    4. 10.4 静电放电警告
    5. 10.5 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.3.4 Analog Current Monitor Output (IMON)

TPS1211x-Q1 features an accurate analog load current monitor output (IMON) with adjustable gain. The current source at IMON terminal is configured to be proportional to the current flowing through the RSNS current sense resistor. This current can be converted to a voltage using a resistor RIMON from IMON terminal to GND terminal. This voltage, computed using Equation 11 can be used as a means of monitoring current flow through the system.

Use Equation 11 to calculate the V(IMON).

Equation 11. V ( I M O N )   =   ( V S N S   +   V ( O S _ S E T ) )   ×   G a i n

Where VSNS = I_LOAD × RSNS and V(OS_SET) is the input referred offset (± 200 µV) of the current sense amplifier (VSNS to V(IMON) scaling). Use the following equation to calculate gain.

Equation 12. TPS1211-Q1
Where 0.9 is the current mirror factor between the current sense amplifier and the IMON pass FET.

The maximum voltage range for monitoring the current (V(IMONmax)) is limited to minimum([V(VS) – 0.5V], 5.5V) to ensure linear output. This puts limitation on maximum value of RIMON resistor. The IMON pin has an internal clamp of 6.5 V (typical).

Accuracy of the current mirror factor is < ± 1%. Use the following equation to calculate the overall accuracy of V(IMON).

Equation 13. % V(IMON) = V(OS_SET)VSNS × 100

Figure 8-12 shows external connections and simplified block diagram of current sensing and overcurrent protection implementation.

TPS1211-Q1 Current Sensing and Overcurrent Protection Figure 8-12 Current Sensing and Overcurrent Protection

In TPS12110-Q1 and TPS12111-Q1, IMON amplifer output is turned OFF when PD is pulled low to SRC (due to INP pulled low or fault event) whereas IMON output remains enabled in TPS12112-Q1 even if PD is pulled low to SRC. In TPS12112-Q1, IMON output gets disabled only when the device is disabled by pulling EN/UVLO low below V(ENF) or V(VS) below V(VS_PORF).

TPS12112-Q1 can be used in applications where grouped IMON output is desired as shown in Figure 8-13:

TPS1211-Q1 TPS12112-Q1 Application Circuit with Grouped IMON Output Figure 8-13 TPS12112-Q1 Application Circuit with Grouped IMON Output
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |