米6体育平台手机版

ZHCSLK6A July 2021 – December 2021 TPS1HC100-Q1

PRODUCTION DATA

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)

PWP|14

散热焊盘机械数据 (封装 | 引脚)

订购信息

zhcslk6a_oa

9.2.2.3 EMC Transient Disturbances Test

Due to the severe electrical conditions in the automotive environment, immunity capacity against electrical transient disturbances is required, especially for a high-side power switch, which is connected directly to the battery. Detailed test requirements are in accordance with the ISO 7637-2:2011 and ISO 16750-2:2010 standards. The TPS1HC100-Q1 device is tested and certificated by a third-party organization.

Table 9-4 ISO 7637-2:2011(E) in 12-V System⁽¹⁾⁽²⁾⁽³⁾⁽⁴⁾

Test Item	Test Pulse Severity Level and vs Accordingly		Pulse Duration (t_d)	Minimum Number of Pulses or Test Time	Burst-Cycle Pulse-Repetition Time		Input Resistance (Ω)	Function Performance Status Classification
Test Item	Level	Vs/V	Pulse Duration (t_d)	Minimum Number of Pulses or Test Time	MIN	MAX	Input Resistance (Ω)	Function Performance Status Classification
1	III	–112	2 ms	500 pulses	0.5 s	e s	10	Status II
2a	III	55	50 µs	500 pulses	0.2 s	5 s	2	Status II
2b	IV	10	0.2 to 2 s	10 pulses	0.5 s	5 s	0 to 0.05	Status II
3a	IV	–220	0.1 µs	1h	90 ms	100 ms	50	Status II
3b	IV	150	0.1 µs	1h	90 ms	100 ms	50	Status II

(1) Tested both under input low condition and high condition.

(2) Considering the worst test condition, it is tested without any filter capacitors in V_BB and V_OUT

(3) GND pin network is a 1-kΩ resistor in parallel with a diode BAS21-7-F.

(4) Status II: the function does not perform as designed during the test, but returns automatically to normal operation after the test.

Table 9-5 ISO 16750-2:2010(E) Load Dump Test B in 12-V System⁽¹⁾⁽²⁾⁽³⁾⁽⁴⁾⁽⁵⁾

Test Item	Test Pulse Severity Level and vs Accordingly		Pulse Duration (t_d)	Minimum Number of Pulses or Test Time	Burst- Cycle Pulse-Repetition Time		Input Resistance (Ω)	Function Performance Status Classification
Test Item	Level	Vs/V	Pulse Duration (t_d)	Minimum Number of Pulses or Test Time	MIN (s)	MAX (s)	Input Resistance (Ω)	Function Performance Status Classification
Test B		35	40 to 400 ms	5 pulses	60	e	0.5 to 4	Status II

(1) Tested both under input low condition and high condition (DIAG_EN, EN, and VBB are all classified as inputs).

(2) Considering the worst test condition, the device is tested without any filter capacitors on VBB and VOUT.

(3) The GND pin network is a 1-kΩ resistor in parallel with a diode BAS21-7-F.

(4) Status II: the function does not perform as designed during the test, but returns automatically to normal operation after the test.

(5) Select a 39-V external suppressor.