SLVSH67 September   2024 TPS26750

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
      1. 5.1.1 TPS26750 - Absolute Maximum Ratings
      2. 5.1.2 TPS26750 - Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
      1. 5.3.1 TPS26750 - Recommended Operating Conditions
    4. 5.4  Recommended Capacitance
    5. 5.5  Thermal Information
      1. 5.5.1 TPS26750 - Thermal Information
    6. 5.6  Power Supply Characteristics
    7. 5.7  Power Consumption
    8. 5.8  PP_5V Power Switch Characteristics
    9. 5.9  POWER_PATH_EN Characteristics - TPS26750
    10. 5.10 Power Path Supervisory
    11. 5.11 CC Cable Detection Parameters
    12. 5.12 CC VCONN Parameters
    13. 5.13 CC PHY Parameters
    14. 5.14 Thermal Shutdown Characteristics
    15. 5.15 ADC Characteristics
    16. 5.16 Input/Output (I/O) Characteristics
    17. 5.17 BC1.2 Characteristics
    18. 5.18 I2C Requirements and Characteristics
    19. 5.19 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  USB-PD Physical Layer
        1. 7.3.1.1 USB-PD Encoding and Signaling
        2. 7.3.1.2 USB-PD Bi-Phase Marked Coding
        3. 7.3.1.3 USB-PD Transmit (TX) and Receive (Rx) Masks
        4. 7.3.1.4 USB-PD BMC Transmitter
        5. 7.3.1.5 USB-PD BMC Receiver
        6. 7.3.1.6 Squelch Receiver
      2. 7.3.2  Power Management
        1. 7.3.2.1 Power-On And Supervisory Functions
        2. 7.3.2.2 VBUS LDO
      3. 7.3.3  Power Paths
        1. 7.3.3.1 Internal Sourcing Power Paths
          1. 7.3.3.1.1 PP_5V Current Clamping
          2. 7.3.3.1.2 PP_5V Local Overtemperature Shut Down (OTSD)
          3. 7.3.3.1.3 PP_5V OVP
          4. 7.3.3.1.4 PP_5V UVLO
          5. 7.3.3.1.5 PP_5Vx Reverse Current Protection
          6. 7.3.3.1.6 PP_CABLE Current Clamp
          7. 7.3.3.1.7 PP_CABLE Local Overtemperature Shut Down (OTSD)
          8. 7.3.3.1.8 PP_CABLE UVLO
      4. 7.3.4  Cable Plug and Orientation Detection
        1. 7.3.4.1 Configured as a Source
        2. 7.3.4.2 Configured as a Sink
        3. 7.3.4.3 Configured as a DRP
        4. 7.3.4.4 Dead Battery Advertisement
      5. 7.3.5  Overvoltage Protection (CC1, CC2)
      6. 7.3.6  Default Behavior Configuration (ADCIN1, ADCIN2)
      7. 7.3.7  ADC
      8. 7.3.8  BC 1.2 (USB_P, USB_N)
      9. 7.3.9  Digital Interfaces
        1. 7.3.9.1 General GPIO
        2. 7.3.9.2 I2C Interface
      10. 7.3.10 Digital Core
      11. 7.3.11 I2C Interface
        1. 7.3.11.1 I2C Interface Description
          1. 7.3.11.1.1 I2C Clock Stretching
          2. 7.3.11.1.2 I2C Address Setting
          3. 7.3.11.1.3 Unique Address Interface
    4. 7.4 Device Functional Modes
      1. 7.4.1 Pin Strapping to Configure Default Behavior
      2. 7.4.2 Power States
    5. 7.5 Thermal Shutdown
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
        1. 8.2.1.1 Programmable Power Supply (PPS) - Design Requirements
        2. 8.2.1.2 Liquid Detection Design Requirements
        3. 8.2.1.3 BC1.2 Application Design Requirements
        4. 8.2.1.4 USB Data Support Design Requirements
        5. 8.2.1.5 EPR Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Programmable Power Supply (PPS)
        2. 8.2.2.2 Liquid Detection
        3. 8.2.2.3 BC1.2 Application
        4. 8.2.2.4 USB Data Support
        5. 8.2.2.5 Power Delivery EPR Support
      3. 8.2.3 Application Curves
        1. 8.2.3.1 Programmable Power Supply (PPS) Application Curves
        2. 8.2.3.2 Liquid Detection Application Curves
        3. 8.2.3.3 BC1.2 Application Curves
        4. 8.2.3.4 USB Data Support Application Curves
        5. 8.2.3.5 EPR Application Curves
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 3.3V Power
        1. 8.3.1.1 VIN_3V3 Input Switch
      2. 8.3.2 1.5V Power
      3. 8.3.3 Recommended Supply Load Capacitance
    4. 8.4 Layout
      1. 8.4.1 TPS26750 - Layout
        1. 8.4.1.1 Layout Guidelines
          1. 8.4.1.1.1 Recommended Via Size
          2. 8.4.1.1.2 Minimum Trace Widths
        2. 8.4.1.2 Layout Example
          1. 8.4.1.2.1 TPS26750 Schematic Layout Example
          2. 8.4.1.2.2 TPS26750 Layout Example - PCB Plots
            1. 8.4.1.2.2.1 TPS26750 Component Placement
            2. 8.4.1.2.2.2 TPS26750 PP5V
            3. 8.4.1.2.2.3 TPS26750 PP_EXT
            4. 8.4.1.2.2.4 TPS26750 VBUS
            5. 8.4.1.2.2.5 TPS26750 I/O
            6. 8.4.1.2.2.6 TPS26750 PPEXT Gate Driver
            7. 8.4.1.2.2.7 TPS26750 GND
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • RSM|32
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.3.11 I2C Interface

The TPS26750 has one I2C target interface ports: I2Ct. I2C port I2Ct is comprised of the I2Ct_SDA, I2Ct_SCL, and I2Ct_IRQ pins. This interface provide general status information about the TPS26750, as well as the ability to control the TPS26750 behavior, supporting communications to/from a connected device and/or cable supporting BMC USB-PD, and providing information about connections detected at the USB-C receptacle.

When the TPS26750 is in 'APP ' mode TI recommends to use standard mode or Fast mode (that is a clock speed no higher than 400 kHz). However, in the BOOT mode when a patch bundle is loaded Fast Mode Plus can be used (see fSCLS).

The TPS26750 has one I2C controller interface port. I2C is comprised of the I2C_SDA and I2C_SCL pins. This interface can be used to read from or write to external target devices.

During boot, the TPS26750 attempts to read patch and Application Configuration data from an external EEPROM with a 7-bit target address of 0x50. The EEPROM must be at least 36 kilo-bytes.

Table 7-4 I2C Summary
I2C BUSTYPETYPICAL USAGE
I2CtTargetOptionally can be connected to an external MCU. Also used to load the patch and application configuration.
I2CcControllerConnect to a I2C EEPROM, Battery Charger. Use the LDO_3V3 pin as the pullup voltage. Multi-controller configuration is not supported.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |