ZHCSMM1C April   2023  – February 2024 TPS274C65

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
    1.     7
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 SPI Timing Requirements
    8. 6.8 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Pin Diagrams
      2. 8.3.2 SPI Mode Operation
        1. 8.3.2.1 Diagnostic Bit Behavior
      3. 8.3.3 Programmable Current Limit
        1. 8.3.3.1 Inrush Current Handling
      4. 8.3.4 DO_EN Feature
      5. 8.3.5 Protection Mechanisms
        1. 8.3.5.1 Overcurrent Protection
        2. 8.3.5.2 Short Circuit Protection
          1. 8.3.5.2.1 VS During Short-to-Ground
        3. 8.3.5.3 Inductive-Load Switching-Off Clamp
        4. 8.3.5.4 Inductive Load Demagnetization
        5. 8.3.5.5 Thermal Shutdown
        6. 8.3.5.6 Undervoltage protection on VS
        7. 8.3.5.7 Undervoltage Lockout on Low Voltage Supply (VDD_UVLO)
        8. 8.3.5.8 Power-Up and Power-Down Behavior
        9. 8.3.5.9 Reverse Current Blocking
      6. 8.3.6 Diagnostic Mechanisms
        1. 8.3.6.1 Current Sense
          1. 8.3.6.1.1 RSNS Value
            1. 8.3.6.1.1.1 SNS Output Filter
        2. 8.3.6.2 Fault Indication
          1. 8.3.6.2.1 Current Limit Behavior
        3. 8.3.6.3 Short-to-Battery and Open-Load Detection
        4. 8.3.6.4 On-State Wire-Break Detection
        5. 8.3.6.5 Off State Wire-Break Detection
        6. 8.3.6.6 ADC
      7. 8.3.7 LED Driver
    4. 8.4 Device Functional Modes
      1. 8.4.1 OFF/POR
      2. 8.4.2 INIT
      3. 8.4.3 Active
    5. 8.5 TPS274C65BS Available Registers List
    6. 8.6 TPS274C65 Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 IEC 61000-4-5 Surge
        2. 9.2.2.2 Loss of GND
        3. 9.2.2.3 Paralleling Channels
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 接收文档更新通知
    2. 10.2 支持资源
    3. 10.3 Trademarks
    4. 10.4 静电放电警告
    5. 10.5 术语表
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Table 5-1 Pin Functions – Version AS and BS Do not connect for pins labeled DNC
PIN TYPE(1) DESCRIPTION
NO. TPS274C65AS, 
TPS274C65ASH		 TPS274C65BS
1 READY DNC(3) O Logic low output indicating the IC is ready for SPI data transmission (connect to GND pin of the IC with resistor).
2 FLT FLT O Fault output – on any (one or more) channel - open drain, needs to be pulled up to VDD pin.
3 DO_EN DO_EN I Setting this pin low would disable all of the outputs. Set high to enable SPI based output Internal pull-down.
4 VDD(2) VDD(2) P Logic Supply Input(2).
5, 21 GND GND — Device ground.
6 ISNS DNC(3) O SNS current output – use a parallel RC network to the GND pin of the IC.
7 SDO SDO O SPI Data Output from the device.
8 SDI SDI I SPI device (secondary) data input.
9 SCLK SCLK O SPI Clock Input.
10 CS CS I SPI Chip select.
11 RCB3 DNC(3) O Gate connection for reverse current blocking FET Ch3.
12, 13 OUT3 OUT3 O Output voltage for channel 3.
14–17 VS VS P 24V Switch Supply input to the IC.
18, 19 OUT4 OUT4 O Output voltage for channel 4.
20 RCB4 DNC(3) O Gate connection for reverse current blocking FET Ch4.
22 LEDOUT1 DNC(3) O LED matrix select driver.
23 LEDOUT2 DNC(3) O LED matrix select driver.
24 LEDOUT3 DNC(3) O LED matrix select driver.
25 LEDOUT4 DNC(3) O LED matrix select driver.
26 DNC(3) DNC(3) — Do not connect.
27 DNC(3) DNC(3) — Do not connect.
28 DSPI DSPI I Configure the device in daisy chain SPI mode when the pin is pulled HI.
29 REG_EN REG_EN I Internal Regulator Enable pin, float to enable. Tie to GND to disable and use an external supply input to VDD.
30 ADDCFG ADDCFG I SPI IC Address Configuration pin – set the 3-bit address of each IC (up to 8 on one board) with a resistor to GND pin of the IC. Leave floating if using Daisy Chain mode.
31 RCB2 DNC(3) O Gate connection for reverse current blocking FET Ch2.
32, 33 OUT2 OUT2 O Output voltage for channel 2.
34–37 VS VS P 24V Switch Supply input to the IC.
38, 39 OUT1 OUT1 O Output voltage for channel 1.
40 RCB1 DNC(3) O Gate connection for reverse current blocking FET Ch1.
Exposed Pad GND GND I Connected to GND pin of the IC.
(1) I = input, O = output, P = power.
(2) When the device is configured to support an external regulator connected to VDD, it is required that the
supply input for the external regulator is derived from the same VS supply of TPS274C65 as shown in the Typical Application Schematic.
(3) Do not connect for pins labeled DNC.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |