ZHCSI26C August   2010  – April 2018 TPS54320

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1.     Device Images
      1.      简化原理图
      2.      效率与负载电流间的关系
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Fixed Frequency PWM Control
      2. 7.3.2  Continuous Current Mode Operation (CCM)
      3. 7.3.3  VIN and Power VIN Pins (VIN and PVIN)
      4. 7.3.4  Voltage Reference
      5. 7.3.5  Adjusting the Output Voltage
      6. 7.3.6  Safe Start-up into Prebiased Outputs
      7. 7.3.7  Error Amplifier
      8. 7.3.8  Slope Compensation
      9. 7.3.9  Enable and Adjusting UVLO
      10. 7.3.10 Slow Start (SS/TR)
      11. 7.3.11 Power Good (PWRGD)
      12. 7.3.12 Bootstrap Voltage (BOOT) and Low Dropout Operation
      13. 7.3.13 Sequencing (SS/TR)
      14. 7.3.14 Output Overvoltage Protection (OVP)
      15. 7.3.15 Overcurrent Protection
        1. 7.3.15.1 High-Side MOSFET Overcurrent Protection
        2. 7.3.15.2 Low-Side MOSFET Overcurrent Protection
      16. 7.3.16 Thermal Shutdown
      17. 7.3.17 Small Signal Model for Loop Response
      18. 7.3.18 Simple Small Signal Model for Peak Current Mode Control
      19. 7.3.19 Small Signal Model for Frequency Compensation
    4. 7.4 Device Functional Modes
      1. 7.4.1 Adjustable Switching Frequency and Synchronization (RT/CLK)
      2. 7.4.2 Adjustable Switching Frequency (RT Mode)
      3. 7.4.3 Synchronization (CLK Mode)
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Custom Design With WEBENCH® Tools
        2. 8.2.2.2  Operating Frequency
        3. 8.2.2.3  Output Inductor Selection
        4. 8.2.2.4  Output Capacitor Selection
        5. 8.2.2.5  Input Capacitor Selection
        6. 8.2.2.6  Slow-Start Capacitor Selection
        7. 8.2.2.7  Bootstrap Capacitor Selection
        8. 8.2.2.8  UVLO Set Point
        9. 8.2.2.9  Output Voltage Feedback Resistor Selection
          1. 8.2.2.9.1 Minimum Output Voltage
        10. 8.2.2.10 Compensation Component Selection
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11器件和文档支持
    1. 11.1 器件支持
      1. 11.1.1 使用 WEBENCH® 工具创建定制设计
    2. 11.2 文档支持
    3. 11.3 商标
    4. 11.4 静电放电警告
    5. 11.5 术语表
  12. 12机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.5 Electrical Characteristics

TJ= –40°C to 150°C, VIN = 4.5 to 17 V, PVIN = 1.6 to 17 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY VOLTAGE (VIN AND PVIN PINS)
PVIN operating input voltage 1.6 17 V
VIN operating input voltage 4.5 17 V
VIN internal UVLO threshold VIN rising 4.0 4.5 V
VIN internal UVLO hysteresis 150 mV
VIN shutdown supply Current EN = 0 V 2 5 μA
VIN operating – non switching supply current VSENSE = 810 mV 600 800 μA
ENABLE AND UVLO (EN PIN)
Enable threshold Rising 1.21 1.26 V
Enable threshold Falling 1.10 1.17 V
EN pin sourcing current EN low EN = 1.1 V 1.15 μA
EN pin sourcing current EN high EN = 1.3 V 3.4 μA
VOLTAGE REFERENCE
Voltage reference 0 A ≤ IOUT ≤ 3 A 0.792 0.800 0.808 V
MOSFET
High-side switch resistance(1) BOOT-PH = 3 V 77 116 mΩ
High-side switch resistance(1) BOOT-PH = 6 V 57 103 mΩ
Low-side Switch Resistance(1) VIN = 12 V 50 87 mΩ
ERROR AMPLIFIER
Error amplifier Transconductance (gm) –2 μA < I(COMP)< 2 μA, V(COMP) = 1 V 1300 μMhos
Error amplifier dc gain VSENSE = 0.8 V 1000 3100 V/V
Error amplifier source/sink V(COMP) = 1 V, 100-mV input overdrive ±110 μA
Start switching threshold 0.25 V
COMP to Iswitch gm 12 A/V
CURRENT LIMIT
High-side switch current limit threshold 4.2 6.2 A
Low-side switch sourcing current limit 3.8 5.8 A
Low-side switch sinking current limit 1 2.6 A
Hiccup wait time before triggering hiccup 512 cycles
Hiccup time before restart 16384 cycles
THERMAL SHUTDOWN
Thermal shutdown 160 175 °C
Thermal shutdown hysteresis 10 °C
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
Minimum switching frequency Rrt = 240 kΩ (1%) 160 200 240 kHz
Switching frequency Rrt = 100 kΩ (1%) 400 480 560 kHz
Maximum switching frequency Rrt = 40.2 kΩ (1%) 1080 1200 1320 kHz
Minimum pulse width 20 ns
RT/CLK high threshold 2 V
RT/CLK low threshold 0.8 V
RT/CLK falling edge to PH rising edge delay Measure at 500 kHz with RT resistor in series 62 ns
Switching frequency range (RT mode set point and PLL mode) 200 1200 kHz
PH (PH PIN)
Minimum on time Measured at 90% to 90% of PH,
TA = 25°C, IPH = 2 A		 97 135 ns
Minimum off time BOOT-PH ≥ 3 V 0 ns
BOOT (BOOT PIN)
BOOT-PH UVLO 2.1 3 V
SLOW START AND TRACKING (SS/TR PIN)
SS charge current 2.3 μA
SS/TR to VSENSE matching V(SS/TR) = 0.4 V 29 60 mV
POWER GOOD (PWRGD PIN)
VSENSE threshold VSENSE falling (Fault) 91 % Vref
VSENSE rising (Good) 94 % Vref
VSENSE rising (Fault) 109 % Vref
VSENSE falling (Good) 106 % Vref
Output high leakage VSENSE = Vref, V(PWRGD) = 5.5 V 30 100 nA
Output low I(PWRGD) = 2 mA 0.3 V
Minimum VIN for valid output V(PWRGD)< 0.5V at 100 μA 0.6 1 V
Minimum SS/TR voltage for PWRGD valid 1.2 1.4 V
(1) Measured at pins
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |