ZHCSBT5C October   2013  – January 2017 TPS54541

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
  6. 6  Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Switching Requirements
    8. 6.8 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Fixed-Frequency PWM Control
      2. 7.3.2  Slope Compensation Output Current
      3. 7.3.3  Pulse Skip Eco-mode
      4. 7.3.4  Low Dropout Operation and Bootstrap Voltage (BOOT)
      5. 7.3.5  Error Amplifier
      6. 7.3.6  Adjusting the Output Voltage
      7. 7.3.7  Enable and Adjusting Undervoltage Lockout
      8. 7.3.8  Soft-Start/Tracking Pin (SS/TR)
      9. 7.3.9  Sequencing
      10. 7.3.10 Constant Switching Frequency and Timing Resistor (RT/CLK) Pin)
      11. 7.3.11 Synchronization to RT/CLK Pin
      12. 7.3.12 Maximum Switching Frequency
      13. 7.3.13 Accurate Current Limit Operation
      14. 7.3.14 Power Good (PWRGD Pin)
      15. 7.3.15 Overvoltage Protection
      16. 7.3.16 Thermal Shutdown
      17. 7.3.17 Small-Signal Model for Loop Response
      18. 7.3.18 Simple Small-Signal Model for Peak-Current-Mode Control
      19. 7.3.19 Small Signal Model for Frequency Compensation
    4. 7.4 Device Functional Modes
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Buck Converter for 6-V to 42-V Input and 3.3-V at 5-A Output
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1  Custom Design with WEBENCH® Tools
          2. 8.2.1.2.2  Selecting the Switching Frequency
          3. 8.2.1.2.3  Output Inductor Selection (LO)
          4. 8.2.1.2.4  Output Capacitor
          5. 8.2.1.2.5  Catch Diode
          6. 8.2.1.2.6  Input Capacitor
          7. 8.2.1.2.7  Slow-Start Capacitor
          8. 8.2.1.2.8  Bootstrap Capacitor Selection
          9. 8.2.1.2.9  Undervoltage Lockout Set Point
          10. 8.2.1.2.10 Output Voltage and Feedback Resistors Selection
          11. 8.2.1.2.11 Compensation
          12. 8.2.1.2.12 Power Dissipation Estimate
          13. 8.2.1.2.13 Safe Operating Area
          14. 8.2.1.2.14 Discontinuous Conduction Mode and Eco-mode Boundary
        3. 8.2.1.3 Application Curves
      2. 8.2.2 Inverting Buck-Boost Topology for Positive Input to Negative Output
      3. 8.2.3 Split-Rail Topology for Positive Input to Negative and Positive Output
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
    3. 10.3 Estimated Circuit Area
  11. 11器件和文档支持
    1. 11.1 器件支持
      1. 11.1.1 Third-Party Products Disclaimer
      2. 11.1.2 开发支持
    2. 11.2 文档支持
      1. 11.2.1 相关文档　
      2. 11.2.2 《使用 WEBENCH® 工具定制设计方案》
    3. 11.3 接收文档更新通知
    4. 11.4 社区资源
    5. 11.5 商标
    6. 11.6 静电放电警告
    7. 11.7 Glossary
  12. 12机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6 Specifications

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Voltage VIN –0.3 45 V
EN –0.3 8.4
BOOT–SW –0.3 8
FB –0.3 3
COMP –0.3 3
PWRGD –0.3 6
SS/TR –0.3 3
RT/CLK –0.3 3.6
SW –0.6 45
SW, 5-ns Transient –7 65
SW, 10-ns Transient –2 45
Operating junction temperature –40 150 °C
Storage temperature –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

6.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V
Charged device model (CDM), per JEDEC specification JESD22-C101(2) ±500
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNIT
VVIN Supply input voltage 4.5 42 V
VO Output voltage 0.8 41.1 V
IO Output current 0 5 A
TJ Operating junction temperature –40 150 °C

6.4 Thermal Information

THERMAL METRIC(1)(2) TPS54541 UNIT
DPR (WSON)
10 PINS
RθJA Junction-to-ambient thermal resistance (standard board) 35.1 °C/W
RθJC(top) Junction-to-case(top) thermal resistance 34.1 °C/W
RθJB Junction-to-board thermal resistance 12.3 °C/W
ψJT Junction-to-top characterization parameter 0.3 °C/W
ψJB Junction-to-board characterization parameter 12.5 °C/W
RθJC(bot) Junction-to-case(bottom) thermal resistance 2.2 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
(2) Power rating at a specific ambient temperature TA should be determined with a junction temperature of 150°C. This is the point where distortion starts to substantially increase. See Power Dissipation Estimate for more information.

6.5 Electrical Characteristics

TJ = –40°C to 150°C, VIN = 4.5 V to 42 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY VOLTAGE (VIN PIN)
Operating input voltage 4.5 42 V
Internal undervoltage lockout threshold Rising 4.1 4.3 4.48 V
Internal undervoltage lockout threshold hysteresis 325 mV
Shutdown supply current EN = 0 V, 25°C, 4.5 V ≤ VIN ≤ 42 V 2.25 4.5 μA
Operating: nonswitching supply current FB = 0.9 V, TA = 25°C 152 200
ENABLE AND UVLO (EN PIN)
Enable threshold voltage No voltage hysteresis, rising and falling 1.1 1.2 1.3 V
Input current Enable threshold +50 mV –4.6 μA
Enable threshold –50 mV –0.58 –1.2 -1.8
Hysteresis current –2.2 –3.4 -4.5 μA
Enable to COMP active VIN = 12 V, TA = 25°C 540 µs
VOLTAGE REFERENCE
Voltage reference 0.792 0.8 0.808 V
HIGH-SIDE MOSFET
On-resistance VIN = 12 V, BOOT-SW = 6 V 87 185 mΩ
ERROR AMPLIFIER
Input current 50 nA
Error amplifier transconductance (gm) –2 μA < ICOMP < 2 μA, VCOMP = 1 V 350 μS
Error amplifier transconductance (gm) during soft-start –2 μA < ICOMP < 2 μA, VCOMP = 1 V, VFB = 0.4 V 77 μS
Error amplifier dc gain VFB = 0.8 V 10,000 V/V
Min unity gain bandwidth 2500 kHz
Error amplifier source/sink V(COMP) = 1 V, 100 mV overdrive ±30 μA
COMP to SW current transconductance 17 A/V
CURRENT LIMIT
Current limit threshold All VIN and temperatures, Open Loop(1) 6.3 7.5 8.8 A
All temperatures, VIN = 12 V, Open Loop(1) 6.3 7.5 8.3
VIN = 12 V, TA = 25°C, Open Loop(1) 7.1 7.5 7.9
Current limit threshold delay 60 ns
THERMAL SHUTDOWN
Thermal shutdown 176 °C
Thermal shutdown hysteresis 12 °C
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
RT/CLK high threshold 1.55 2 V
RT/CLK low threshold 0.5 1.2 V
SOFT START AND TRACKING (SS/TR PIN)
Charge current VSS/TR = 0.4 V 1.7 µA
SS/TR-to-FB matching VSS/TR = 0.4 V 42 mV
SS/TR-to-reference crossover 98% nominal 1.16 V
SS/TR discharge current (overload) FB = 0 V, VSS/TR = 0.4 V 354 µA
SS/TR discharge voltage FB = 0 V 54 mV
POWER GOOD (PWRGD PIN)
FB threshold for PWRGD low FB falling 90%
FB threshold for PWRGD high FB rising 93%
FB threshold for PWRGD low FB rising 108%
FB threshold for PWRGD high FB falling 106%
Hysteresis FB falling 2.5%
Output high leakage VPWRGD = 5.5 V, TA = 25°C 10 nA
On resistance IPWRGD = 3 mA, VFB < 0.79 V 45 Ω
Minimum VIN for defined output VPWRGD < 0.5 V, IPWRGD = 100 µA 0.9 2 V
(1) Open Loop current limit measured directly at the SW pin and is independent of the inductor value and slope compensation.

6.6 Timing Requirements

TJ = –40°C to 150°C, VIN = 4.5 V to 42 V (unless otherwise noted)
MIN NOM MAX UNIT
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
Minimum CLK input pulse width 15 ns
RT/CLK falling edge to SW rising edge delay – Measured at 500 kHz with RT resistor in series 55 ns

6.7 Switching Requirements

TJ = –40°C to 150°C, VIN = 4.5 V to 42 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN NOM MAX UNIT
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
ƒSW Switching frequency RT = 200 kΩ 450 500 550 kHz
Switching frequency range using RT mode 100 2500 kHz
Switching frequency range using CLK mode 160 2300 kHz
PLL lock in time Measured at 500 kHz 78 μs

6.8 Typical Characteristics

TPS54541 C001_SLVSBO1.png
Figure 1. ON Resistance vs Junction Temperature
TPS54541 C003_SLVSBO1.png
Figure 3. Switch Current Limit vs Junction Temperature
TPS54541 C005_SLVSC57.png
Figure 5. Switching Frequency vs Junction Temperature
TPS54541 C007_SLVSBO1.png
Figure 7. Switching Frequency vs RT/CLK Resistance High Frequency Range
TPS54541 C009_SLVSBO1.png
Figure 9. EA Transconductance During Soft-Start vs Junction Temperature
TPS54541 C011_SLVSBO1.png
Figure 11. EN Pin Current vs Junction Temperature
TPS54541 C013_SLVSBO1.png
Figure 13. EN Pin Current Hysteresis vs Junction Temperature
TPS54541 C015_SLVSBO1.png
Figure 15. Shutdown Supply Current vs Junction Temperature
TPS54541 C017_SLVSBO1.png
Figure 17. VIN Supply Current vs Junction Temperature
TPS54541 C019_SLVSBO1.png
Figure 19. BOOT-SW UVLO vs Junction Temperature
TPS54541 C021_SLVSBO1.png
Figure 21. PWRGD ON Resistance vs Junction Temperature
TPS54541 C024_SLVSBO1.png
Figure 23. SS/TR to FB Offset vs FB
TPS54541 C026_SLVSBO1.png
Figure 25. 5-V Start and Stop Voltage
(see Low Dropout Operation and Bootstrap Voltage (BOOT))
TPS54541 C002_SLVSBO1.png
Figure 2. Voltage Reference vs Junction Temperature
TPS54541 C004_SLVSC57.png
Figure 4. Switch Current Limit vs Input Voltage
TPS54541 C006_SLVSBO1.png
Figure 6. Switching Frequency vs RT/CLK Resistance Low Frequency Range
TPS54541 C008_SLVSBO1.png
Figure 8. EA Transconductance vs Junction Temperature
TPS54541 C010_SLVSBO1.png
Figure 10. EN Pin Voltage vs Junction Temperature
TPS54541 C012_SLVSBO1.png
Figure 12. EN Pin Current vs Junction Temperature
TPS54541 C014_SLVSBO1.png
Figure 14. Switching Frequency vs FB
TPS54541 C016_SLVSC57.png
Figure 16. Shutdown Supply Current vs Input Voltage (VIN)
TPS54541 C018_SLVSC57.png
Figure 18. VIN Supply Current vs Input Voltage
TPS54541 C020_SLVSBO1.png
Figure 20. Input Voltage UVLO vs Junction Temperature
TPS54541 C022_SLVSBO1.png
Figure 22. PWRGD Threshold vs Junction Temperature
TPS54541 C025_SLVSBO1.png
Figure 24. SS/TR to FB Offset vs Temperature
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |