米6体育平台手机版

ZHCSPB1B November 2021 – July 2022 TPS62441-Q1 , TPS62442-Q1

PRODUCTION DATA

封装选项

机械数据 (封装 | 引脚)

RQR|14
- MPQF624

散热焊盘机械数据 (封装 | 引脚)

RQR|14
- QFND745

订购信息

9.3.2 COMP/FSET

This pin allows to set three different parameters:

Internal compensation settings for the control loop (two settings available)
The switching frequency in PWM mode from 1.8 MHz to 4 MHz
Enable and disable spread spectrum clocking (SSC)

A resistor from COMP/FSET to GND changes the compensation as well as the switching frequency. The change in compensation allows the user to adopt the device to different values of output capacitance. Place the resistor close to the pin to keep the parasitic capacitance on the pin to a minimum. The compensation setting is sampled at start-up of the converter, so a change in the resistor during operation only has an effect on the switching frequency, but not on the compensation.

To save external components, the pin can also be directly tied to VIN or GND to set a pre-defined setting. Do not leave the pin floating.

The switching frequency has to be selected based on the input voltage and the output voltage to meet the specifications for the minimum on time and minimum off time.

Example: V_IN = 5 V, V_OUT = 1 V --> duty cycle = 1 V / 5 V = 0.2

--> t_on,min = 1 / fs × 0.2
--> f_sw,max = 1 / t_on,min × 0.2 = 1 / 0.075 µs × 0.2 = 2.67 MHz

The compensation range has to be chosen based on the minimum capacitance used. The capacitance can be increased from the minimum value as given in Table 9-1, up to the maximum of 200-µF effective capacitance in both compensation ranges. If the capacitance of an output changes during operation, for example, when load switches are used to connect or disconnect parts of the circuitry, the compensation has to be chosen for the minimum capacitance on the output. With large output capacitance, the compensation must be done based on that large capacitance to get the best load transient response. Compensating for large output capacitance but placing less capacitance on the output can lead to instability.

The switching frequency for the different compensation setting is determined by the following equations.

For compensation (comp) setting 1 with spread spectrum clocking (SSC) disabled:

Equation 1.

For compensation (comp) setting 1 with spread spectrum clocking (SSC) enabled:

Equation 2.

For compensation (comp) setting 2 with spread spectrum clocking (SSC) disabled:

Equation 3.

Table 9-1 Switching Frequency, Compensation, and Spread Spectrum Clocking

R_CF	Compensation	Switching Frequency	Minimum Output Capacitance For V_OUT < 1 V	Minimum Output Capacitance For V_OUT < 3.3 V	Minimum Output Capacitance For V_OUT ≥ 3.3 V
10 kΩ .. 4.5 kΩ	for smallest output capacitance (comp setting 1) SSC disabled	1.8 MHz (10 kΩ) .. 4 MHz (4.5 kΩ) according to Equation 1	11 µF	7 µF	5 µF
33 kΩ .. 18 kΩ	for smallest output capacitance (comp setting 1) SSC enabled	1.8 MHz (33 kΩ) .. 4 MHz (18 kΩ) according to Equation 2	11 µF	7 µF	5 µF
100 kΩ .. 45 kΩ	for best transient response (larger output capacitance) (comp setting 2) SSC disabled	1.8MHz (100 kΩ) ..4 MHz (45 kΩ) according to Equation 3	30 µF	18 µF	15 µF
tied to GND	for smallest output capacitance (comp setting 1) SSC disabled	internally fixed 2.25 MHz	11 µF	7 µF	5 µF
tied to V_IN	for best transient response (larger output capacitance) (comp setting 2) SSC enabled	internally fixed 2.25 MHz	30 µF	18 µF	15 µF

Refer to Section 10.1.2.2.2 for further details on the output capacitance required depending on the output voltage.

A too-high resistor value for R_CF is decoded as "tied to V_IN," a value below the lowest range as "tied to GND." The minimum output capacitance in Table 9-1 is for capacitors close to the output of the device. If the capacitance is distributed, a lower compensation setting can be required.