ZHCSL64D april 2019 – may 2023 TPS7H4001-SP
PRODMIX
- 1
- 1 特性
- 2 应用
- 3 说明
- 4 Revision History
- 5 Device Options Table
- 6 Pin Configuration and Functions
-
7 Specifications
- 7.1 Absolute Maximum Ratings
- 7.2 ESD Ratings
- 7.3 Recommended Operating Conditions
- 7.4 Thermal Information
- 7.5 Electrical Characteristics - All Devices
- 7.6 Electrical Characteristics: CDFP and KGD Options
- 7.7 Electrical Characteristics: HTSSOP (SHP) Option
- 7.8 Electrical Characteristics: HTSSOP (QMLP) Option
- 7.9 Quality Conformance Inspection
- 7.10 Typical Characteristics
-
8 Detailed Description
- 8.1 Overview
- 8.2 Functional Block Diagram
- 8.3
Feature Description
- 8.3.1 VIN and Power VIN Pins (VIN and PVIN)
- 8.3.2 Voltage Reference
- 8.3.3 Adjusting the Output Voltage
- 8.3.4 Safe Start-Up Into Prebiased Outputs
- 8.3.5 Error Amplifier
- 8.3.6 Enable and Adjust UVLO
- 8.3.7 Adjustable Switching Frequency and Synchronization (SYNC)
- 8.3.8 Soft-Start (SS/TR)
- 8.3.9 Power Good (PWRGD)
- 8.3.10 Sequencing
- 8.3.11 Output Overvoltage Protection (OVP)
- 8.3.12 Overcurrent Protection
- 8.3.13 Thermal Shutdown
- 8.3.14 Turn-On Behavior
- 8.3.15 Slope Compensation
- 8.3.16 Small Signal Model for Frequency Compensation
- 8.4 Device Functional Modes
-
9 Application and Implementation
- 9.1 Application Information
- 9.2
Typical Application
- 9.2.1 Design Requirements
- 9.2.2
Detailed Design Procedure
- 9.2.2.1 Operating Frequency
- 9.2.2.2 Output Inductor Selection
- 9.2.2.3 Output Capacitor Selection
- 9.2.2.4 Input Capacitor Selection
- 9.2.2.5 Soft-Start Capacitor Selection
- 9.2.2.6 Undervoltage Lockout (UVLO) Set Point
- 9.2.2.7 Output Voltage Feedback Resistor Selection
- 9.2.2.8 Compensation Component Selection
- 9.2.3 Parallel Operation
- 9.2.4 Application Curve
- 9.3 Power Supply Recommendations
- 9.4 Layout
- 10Device and Documentation Support
- 11Mechanical, Packaging, and Orderable Information
封装选项
请参考 PDF 数据表获取器件具体的封装图。
机械数据 (封装 | 引脚)
- DDW|44
- KGD|0
- HKY|34
散热焊盘机械数据 (封装 | 引脚)
- DDW|44
订购信息
8.3.15 Slope Compensation
The device adds a compensating ramp to the switch current signal for all duty cycles. The slope compensation adjusts the peak current during the charging of the inductor to avoid instability of the system. As a result, the ideal slope compensation is defined as the output voltage divided by the inductor size as shown in Equation 10. The slope compensation, SC, can be configured with a resistor to GND connected to the RSC pin. The RSC resistor value, in kΩ, can be calculated using Equation 11, where SC is in A/µs and fSW is in kHz.
Equation 10. 
Equation 11. 