ZHCSO27B May   2021  – December 2022 TPS7H4002-SP

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  VIN and Power VIN Pins (VIN and PVIN)
      2. 7.3.2  Voltage Reference
      3. 7.3.3  Adjusting the Output Voltage
      4. 7.3.4  Safe Start-Up Into Prebiased Outputs
      5. 7.3.5  Error Amplifier
      6. 7.3.6  Slope Compensation
      7. 7.3.7  Enable and Adjust UVLO
      8. 7.3.8  Adjustable Switching Frequency and Synchronization (SYNC)
      9. 7.3.9  Slow Start (SS/TR)
      10. 7.3.10 Power Good (PWRGD)
      11. 7.3.11 Sequencing (SS/TR)
      12. 7.3.12 Output Overvoltage Protection (OVP)
      13. 7.3.13 Overcurrent Protection
        1. 7.3.13.1 High-Side MOSFET Overcurrent Protection
        2. 7.3.13.2 Low-Side MOSFET Overcurrent Protection
      14. 7.3.14 Thermal Shutdown
      15. 7.3.15 Turn-On Behavior
      16. 7.3.16 Small Signal Model for Frequency Compensation
    4. 7.4 Device Functional Modes
      1. 7.4.1 Fixed-Frequency PWM Control
      2. 7.4.2 Continuous Current Mode (CCM) Operation
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Operating Frequency
        2. 8.2.2.2 Output Inductor Selection
        3. 8.2.2.3 Output Capacitor Selection
        4. 8.2.2.4 Output Schottky Diode
        5. 8.2.2.5 Slow Start Capacitor Selection
        6. 8.2.2.6 Undervoltage Lockout (UVLO) Set Point
        7. 8.2.2.7 Output Voltage Feedback Resistor Selection
        8. 8.2.2.8 Compensation Component Selection
      3. 8.2.3 Parallel Operation
      4. 8.2.4 Application Curve
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 接收文档更新通知
    3. 11.3 支持资源
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 术语表
  12. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.5 Electrical Characteristics

TJ = –55°C to 125°C, VIN = PVIN = 3.0 V to 5.5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY VOLTAGE (VIN AND PVIN PINS)
PVIN operating input voltage 3.0 5.5 V
PVIN internal UVLO threshold PVIN rising 2.50 V
PVIN internal UVLO hysteresis 450 mV
VIN operating input voltage 3.0 5.5 V
VIN internal UVLO threshold VIN rising 2.75 3.0 V
VIN internal UVLO hysteresis 150 mV
VIN shutdown supply current VEN = 0 V 1.75 3 mA
VIN operating – non switching supply current VSENSE = VBG 2.5 5 mA
ENABLE AND UVLO (EN PIN)
Enable threshold Rising 1.14 1.18 V
Falling 1.05 1.12
Input current VEN = 1.1 V 6.1 μA
Hysteresis current VEN = 1.3 V 3.0 μA
VOLTAGE REFERENCE
Voltage reference 0 A ≤ Iout ≤ 3 A, –55°C 0.795 0.806 0.817 V
0 A ≤ Iout ≤ 3 A, 25°C 0.796 0.807 0.818
0 A ≤ Iout ≤ 3 A, 125°C 0.797 0.808 0.819
REFCAP voltage 470 nF 1.211 V
MOSFET
High-side switch resistance PVIN=VIN= 3 V, lead length = 4 mm 50 mΩ
High-side switch resistance(1) PVIN=VIN= 5 V, lead length = 4mm 45 mΩ
High-side switch resistance(1) PVIN=VIN= 5.5 V, lead length = 4 mm 43 mΩ
Low-side switch resistance(1) PVIN=VIN= 3 V, lead length = 4mm 35 mΩ
Low-side switch resistance(1) PVIN=VIN= 5 V, lead length = 4mm 34 mΩ
Low-side switch resistance(1) PVIN=VIN= 5.5 V, lead length = 4mm 33 mΩ
ERROR AMPLIFIER
Error amplifier transconductance (gm)(2) –2 μA < ICOMP < 2 μA, V(COMP) = 1 V 900 1400 1900 μS
Error amplifier dc gain(2) VSENSE = 0.8 V 10000 V/V
Error amplifier source current(2) V(COMP) = 1 V, 100-mV input overdrive 85 140 185 μA
Error amplifier sink current (2) V(COMP) = 1 V, 100-mV input overdrive 85 140 185 μA
Error amplifier output resistance (2) 7 MΩ
Start switching threshold(2) 0.25 V
COMP to Iswitch gm(2) -55°C, V(COMP) ≤ 1.1 V 12 S
25°C, V(COMP) ≤ 1.1 V 12
125°C, V(COMP) ≤ 1.1 V 12
CURRENT LIMIT
High-side switch current limit threshold (3) VIN = 3 V 7.9 A
VIN = 5 V 6.2
VIN = 5.5 V 6.2
Low-side switch sourcing current limit(3) VIN = 5 V 8 A
Low-side switch sinking current limit VIN = 5 V 3 A
SLOPE COMPENSATION
Slope compensation fsw = 100 kHz -0.69 A/µs
fsw = 500 kHz -3.4
fsw = 1 MHz -7.0
THERMAL SHUTDOWN
Thermal shutdown 170 °C
Thermal shutdown hysteresis 30 °C
INTERNAL SWITCHING FREQUENCY
Internally set frequency RT = Open 395 500 585 kHz
Externally set frequency RT = 100 kΩ (1%) 395 500 585 kHz
RT = 487 kΩ (1%) 80 100 115
RT = 47 kΩ (1%) 900 1000 1100
EXTERNAL SYNCHRONIZATION
SYNC out low-to-high rise time (10%/90%) Cload = 25 pF 70 130 ns
SYNC out high-to-low fall time (90%/10%) Cload = 25 pF 6 15.5 ns
Falling edge delay time(5) 180 °
SYNC out high level threshold IOH = 50 µA VIN–0.3 V
SYNC out low level threshold IOL = 50 µA 600 mV
SYNC in low level threshold PVIN=VIN= 3 V 700 mV
SYNC in high level threshold PVIN=VIN= 3 V 2.45 V
SYNC in low level threshold PVIN=VIN= 5.5 V 700 mV
SYNC in high level threshold PVIN=VIN= 5.5 V 4.25 V
SYNC in frequency range(4) 100 1000 kHz
PH (PH PIN)
Minimum on time Measured at 10% to 90% of VIN, 25°C, IPH = 2 A 190 235 ns
SLOW START AND TRACKING (SS/TR PIN)
SS charge current 1.5 2.5 3 μA
SS/TR to VSENSE matching V(SS/TR) = 0.4 V 30 90 mV
POWER GOOD (PWRGD PIN)
VSENSE threshold VSENSE falling (fault) 91 % Vref
VSENSE rising (good) 94
VSENSE rising (fault) 109
VSENSE falling (good) 106
Output high leakage VSENSE = Vref, V(PWRGD) = 5 V 30 181 nA
Output low I(PWRGD) = 2 mA 0.3 V
Minimum VIN for valid output V(PWRGD) < 0.5 V at 100 μA 0.6 1 V
Minimum SS/TR voltage for PWRGD 1.55 V
(1) Measured at pins.
(2) Ensured by design only. Not tested in production.
(3) Parameter is not tested in production.
(4) Parameter is production tested at nominal voltage with VIN = PVIN = 5 V.
(5) Bench verified. Not tested in production.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |