米6体育平台手机版

ZHCSK77E September 2009 – July 2024 TS3USB221E

PRODUCTION DATA

封装选项

机械数据 (封装 | 引脚)

RSE|10
- MPQF186D
DRC|10
- MPDS117L

散热焊盘机械数据 (封装 | 引脚)

DRC|10
- QFND013N

订购信息

5.5 Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)⁽¹⁾

PARAMETER		TEST CONDITIONS			MIN	TYP⁽²⁾	MAX	UNIT
V_IK		V_CC = 3.6 V, 2.7 V,	I_I = –18 mA		–1.8			V
I_IN	Control inputs	V_CC = 3.6 V, 2.7 V, 0 V,	V_IN = 0 V to 3.6 V				±1	μA
I_OZ⁽³⁾		V_CC = 3.6 V, 2.7 V, V_O = 0 V to 5.25 V, V_I = 0 V,	V_IN = V_CC or GND, Switch OFF				±1	μA
I_OFF		V_CC = 0 V	V_I/O = 0 V to 5.25 V				±2	μA
			V_I/O = 0 V to 3.6 V				±2
			V_I/O = 0 V to 2.7 V				±1
I_CC		V_CC = 3.6 V, 2.7 V, V_IN = V_CC or GND,	I_I/O = 0 V, Switch ON or OFF				30	μA
I_CC (low power mode)		V_CC = 3.6 V, 2.7 V, V_IN = V_CC or GND	Switch disabled ( OE in high state)				1	μA
I_CC⁽⁴⁾	Control inputs	One input at 1.8 V, Other inputs at V_CC or GND	V_CC = 3.6 V				20	μA
I_CC⁽⁴⁾	Control inputs	One input at 1.8 V, Other inputs at V_CC or GND	V_CC = 2.7 V				0.5	μA
C_in	Control inputs	V_CC = 3.3 V, 2.5 V,	V_IN = 3.3 V or 0 V			1.5	2.5	pF
C_io(OFF)		V_CC = 3.3 V, 2.5 V,	V_I/O = 3.3 V or 0 V,	Switch OFF		3.5	5	pF
C_io(ON)		V_CC = 3.3 V, 2.5 V,	V_I/O = 3.3 V or 0 V,	Switch ON		6	7.5	pF
r_ON⁽⁵⁾		V_CC = 3 V, 2.3 V	V_I = 0 V,	I_O = 30 mA		3	6	Ω
r_ON⁽⁵⁾		V_CC = 3 V, 2.3 V	V_I = 2.4 V,	I_O = –15 mA		3.4	6	Ω
Δr_ON		V_CC = 3 V, 2.3 V	V_I = 0 V,	I_O = 30 mA		0.2		Ω
Δr_ON		V_CC = 3 V, 2.3 V	V_I = 1.7,	I_O = –15 mA		0.2		Ω
r_ON(flat)		V_CC = 3 V, 2.3 V	V_I = 0 V,	I_O = 30 mA		1		Ω
r_ON(flat)		V_CC = 3 V, 2.3 V	V_I = 1.7,	I_O = –15 mA		1		Ω

(1) V_IN and I_IN refer to control inputs. V_I, V_O, I_I, and I_O refer to data pins.

(2) All typical values are at V_CC = 3.3 V (unless otherwise noted), T_A = 25°C.

(3) For I/O ports, the parameter I_OZ includes the input leakage current.

(4) This is the increase in supply current for each input that is at the specified TTL voltage level, rather than V_CC or GND.

(5) Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by the lower of the voltages of the two (A or B) terminals.