ZHCSHY0B March   2018  – June 2018 TS5USBC41

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1.     Device Images
      1.      简化原理图
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Dynamic Characteristics
    7. 6.7 Timing Requirements
    8. 6.8 Typical Characteristics
  7. 7 Parameter Measurement Information
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Powered-off Protection
      2. 8.3.2 Overvoltage Protection
    4. 8.4 Device Functional Modes
      1. 8.4.1 Pin Functions
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12器件和文档支持
    1. 12.1 文档支持
      1. 12.1.1 相关文档
    2. 12.2 接收文档更新通知
    3. 12.3 社区资源
    4. 12.4 商标
    5. 12.5 静电放电警告
    6. 12.6 术语表
  13. 13机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.5 Electrical Characteristics

TA = –40°C to +85°C (Industrial), TA = 0℃ to 70℃ (Standard),VCC = 2.3 V to 5.5 V, GND = 0 V, Typical values are at VCC = 3.3 V, TA = 25°C, (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
POWER
ICC-ACTIVE Active supply current.   OE = 0 V
SEL1, SEL2 = 0 V, 1.8 V or VCC
0 V < VI/O < 3.6 V		 9 22 µA
ICC-OVP Supply current during OVP condition.  OE = 0 V
SEL1, SEL2 = 0 V, 1.8 V or VCC
VI/O > VPOS_THLD 		10 35 μA
ICC_PD Standby powered down supply current OE = 1.8 V or VCC
SEL1 = 0 V, 1.8 V, or VCC
SEL2 = 0 V, 1.8 V, or VCC		 2 6 µA
DC Characteristics
RON ON-state resistance VI/O = 0.4 V
ISINK = 8 mA
Refer to ON-State Resistance Figure 		5.6 9 Ω
ΔRON ON-state resistance match between channels VI/O = 0.4 V
ISINK = 8 mA
Refer to ON-State Resistance Figure 		0.075 0.48 Ω
RON (FLAT)  ON-state resistance flatness  VI/O = 0 V to 0.4 V
ISINK = 8 mA
Refer to ON-State Resistance Figure 		0.1 0.4 Ω
IOFF I/O pin OFF leakage current OE = H
VD± = 0 V or 3.6 V
VCC = 2.3 V to 5.5 V
VD1±or VD2± = 3.6 V or 0 V
Refer to Off Leakage Figure 		-4 0.1 4 µA
IOFF-20V D1/D2+/- pin OFF leakage current during OVP scenario on D+/- OE = H
VD± = 20-V
VCC = 2.3 V to 5.5 V
VD1± or VD2± = 0 V
Refer to Off Leakage Figure 		-0.5 0.5 µA
IOFF-20V-DP/N D+/- pin OFF leakage current during OVP scenario OE = H
VD± = 20-V
VCC = 2.3 V to 5.5 V
VD1± or VD2± = 0 V
Refer to Off Leakage Figure 		140 150 180 µA
IOFF-24V D1/D2 +/- pin OFF leakage current during OVP scenario on D+/-. OE = H
VD± = 24-V
VCC = 2.3 V to 5.5 V
VD1± or VD2± = 0 V
Refer to Off Leakage Figure 		-0.5 0.5 µA
IOFF-24V-DPN D+/- pin OFF leakage current during OVP scenario. OE = H
VD± = 0 V or 24-V
VCC = 2.3 V to 5.5 V
VD1± or VD2± = 0 V
Refer to Off Leakage Figure 		220 250 270 µA
ION ON leakage current. VD± = 0 V or 3.6 V
VD1± and VD2+/- = high-Z
Refer to On Leakage Figure 		-5.5 0.25 7.5 µA
Digital Characteristics
VIH Input logic high SEL1, SEL2, OE 1.4 V
VIL Input logic low SEL1, SEL2, OE 0.5 V
VOL Output logic low FLT
IOL = 3 mA		 0.4 V
IIH Input high leakage current SEL1, SEL2, OE = 1.8 V, VCC -1 1 5 μA
IIL Input low leakage current SEL1, SEL2, OE = 0 V -1 ±0.2 5 μA
RPD Internal pull-down resistor on digital input pins 6 MΩ
CI Digital input capacitance SEL1, SEL2 = 0 V, 1.8 V or VCC
f = 1 MHz		 4 pF
Protection
VOVP_TH OVP positive threshold 4.4 4.8 5.2 V
VOVP_HYST OVP threshold hysteresis 125 250 440 mV
VCLAMP_V Maximum voltage to appear on D1± and D2± pins during OVP scenario
(TS5USBC412, TS5USBC412I)		 VD± = 0 to 24 V
tRISE and tFALL(10% to 90 %) = 100 ns
RL = Open
Switch on or off
OE = 0 V		 11.2 V
VCLAMP_V Maximum voltage to appear on D1± and D2± pins during OVP scenario
(TS5USBC412, TS5USBC412I)		 VD± = 0 to 24 V
tRISE and tFALL(10% to 90 %) = 100 ns
RL = 50Ω
Switch on or off
OE = 0 V		 10.8 V
VCLAMP_V Maximum voltage to appear on D1± and D2± pins during OVP scenario
(TS5USBC410, TS5USBC410I)		 VD± = 0 to 20 V
tRISE and tFALL(10% to 90 %) = 100 ns
RL = Open
Switch on or off
OE = 0 V		 10.8 V
VCLAMP_V Maximum voltage to appear on D1± and D2± pins during OVP scenario
(TS5USBC410, TS5USBC410I)		 VD± = 0 to 20 V
tRISE and tFALL(10% to 90 %) = 100 ns
RL = 50Ω
Switch on or off
OE = 0 V		 9.8 V
VCLAMP_T Maximum OVP transient duration above 5 V (TS5USBC412, TS5USBC412I).    VD± = 0 to 24 V
tRISE and tFALL(10% to 90 %) = 100 ns
RL = Open CL = 10pF
Switch on or off
OE = 0 V		 75 100 ns
VCLAMP_T Maximum OVP transient duration above 5 V
(TS5USBC412, TS5USBC412I)		 VD± = 0 to 24 V
tRISE and tFALL(10% to 90 %) = 100 ns
RL = 50Ω CL = 10pF
Switch on or off
OE = 0 V		 68 95 ns
VCLAMP_T Maximum OVP transient duration above 5 V
(TS5USBC410, TS5USBC410I)		 VD± = 0 to 20 V
tRISE and tFALL(10% to 90 %) = 100 ns
RL = Open CL = 10pF
Switch on or off
OE = 0 V		 64 100 ns
VCLAMP_T Maximum OVP transient duration above 5 V
(TS5USBC410, TS5USBC410I)		 VD± = 0 to 20 V
tRISE and tFALL(10% to 90 %) = 100 ns
RL = 50Ω CL = 10pF
Switch on or off
OE = 0 V		 55 95 ns
tEN_OVP OVP enable time RPU = 10 kΩ to VCC (FLT)
CL = 35 pF
Refer to OVP Timing Diagram Figure 		3 μs
tREC_OVP OVP recovery time RPU = 10 kΩ to VCC (FLT)
CL = 35 pF
Refer to OVP Timing Diagram Figure 		5 μs
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |